Operating instructions

• Before using the device, read the instructions carefully and completely and save them for future reference.
• Use the humidifier only indoors and under specified conditions. Unintended use may damage your health and cause injury.
• Children do not understand the dangers associated with using electrical appliances. Therefore, do not leave children unattended near the humidifier.
• Persons who have not read these instructions, children and persons under the influence of drugs or alcohol should not be allowed to operate the device, at least without supervision.
• Do not use the humidifier if the power cord or plug is damaged, if the device is malfunctioning, or if the humidifier has been dropped or mechanically damaged.
• All types of repairs to electrical appliances must be carried out only by qualified specialists. If repairs are not carried out correctly, the use of the humidifier may become dangerous for the user.
• Before each filling/emptying of the water tank, before cleaning, assembling, or rearranging the humidifier, be sure to unplug the device from the socket.
• Never pull the plug from the outlet with wet hands or while holding the cord.
• The humidifier must be installed on a flat, horizontal surface.
• Never fill the reservoir through the nozzle opening.
• Do not add additives (flavors, essential oils, etc.) to the water.
• Do not immerse the humidifier support shell in water.

General information

The indoor climate becomes comfortable, as a rule, at a relative humidity of 40-60%. The ultrasonic humidifier automatically maintains the humidity you select. If the room is very dry, the device automatically turns on. When the desired humidity is reached, the humidifier stops operating.

Description of the humidifier

Start of operation

• The best place to install a humidifier:
  • not too close to heating devices
  • do not place the humidifier on a heated floor
  • The sprayer should not be directed at plants or other objects.
• Make sure there are no foreign objects in the water tank.
• Fill the tank with clean, cold tap water (not hotter than 40 degrees) and close the tank shutter tightly.
• The scale filter needs to be changed every 2-3 months.
• Insert the water tank into the humidifier and close the lid.
• Wait a few minutes for the tank to fill with water.
• Connect the cable to the set and turn on the humidifier using the ON/OFF switch.
• Full operating power will be achieved 10-15 minutes after the humidifier is turned on.

Replacing the limescale filter

ATTENTION: The water tank is equipped with a limescale filter. This filter needs to be changed every 2-3 months.

After the water in the tank has cooled, turn the tank over and unscrew the shutter. The filter is located on the inside of the tank lid.

Unscrew the scale filter counterclockwise and replace it with a new filter.

Instructions for ultrasonic humidifier 7131

Switching on/off and adjusting humidity levels

By turning the right rotary knob clockwise, you turn on the humidifier and adjust the moisture output from low to high levels.

Humidity regulator

By turning the left rotary knob clockwise you set the desired humidity. It is recommended to set the humidity in the range of 40-60%. If the humidity exceeds the set value, the device will turn off. If the Continuous activity function is set, the humidifier will not turn off.

Instructions for ultrasonic humidifier 7136

Turn on/off

Use the POWER button. After switching on, the following values ​​are set:

• air humidity 60%
• moisture release - level II
• long-term activity function.

These values ​​can be changed by clicking on the corresponding buttons. The display will show both the desired and actual air humidity (flashing indicator light).

As soon as the water in the tank runs out, the control lamp lights up and a sound signal sounds.

Controlling moisture release

The moisture output capacity is selected using the leftmost button:

I - for low moisture output

II - for strong moisture release.

Humidity regulator

By pressing the humidity button you set the desired humidity. It is recommended to set the humidity in the range of 40-60%. If the humidity exceeds the set value, the device will turn off. If the Continuous activity function is set, the humidifier will not turn off.

Setting the timer

Using the timer button, you can set the operating time of the humidifier to 2 hours, 4 hours or the long-term humidification function. Humidity control is active in all three settings.

Cleaning and maintaining the humidifier

• Turn off the appliance and remove the power plug from the socket before cleaning the appliance.
• Clean the water tank and reservoir regularly.
• ATTENTION: water must not get into the bottom of the device.
• Clean the inside of the humidifier with a damp cloth and never use gasoline, glass cleaner or solvents.
• When cleaning the membrane weekly, use only the brush (9).
• The filter on the back of the humidifier should be rinsed with water from time to time.
• Change the water in the tank at least once a week.

Storage

Clean the humidifier as described above and leave it to dry completely.Store the humidifier in a cool, dry place, preferably in the original packaging.

Problems and solutions

Indoor air humidification is a concern for the health and well-being of all family members. A high-quality humidifier effectively solves the problem of dry and polluted air. The equipment restores the required level of humidity in the room and cleanses the environment of harmful impurities. The Boneco air humidifier has an expanded range of functions and is among the most popular.

The Boneko air purifier effectively restores the humidity level in the room. From the first days of use, air purification and freshness are noted. Owners of devices are less likely to suffer from infectious diseases and colds.

Boneco produces humidifiers and air purifiers. The former maintain an optimal level of humidity in the room. The second category is intended to purify the air from harmful impurities that are inevitably contained in it due to a polluted environment.

Humidifiers are divided into 4 types:

• ultrasonic,
• steam,
• traditional,
• air washers - combined humidifiers.

Ultrasonic air purifiers independently measure the humidity level and bring it to the optimal level with a built-in hygrostat in a few hours. Models are equipped with a touchscreen display. Ultrasonic humidifiers consume energy sparingly and do not make noise. The filter is designed for up to 3 months of operation depending on the intensity.

Steam models generate steam. Humidifiers are equipped with a reservoir for water, which, when heated, turns into steam and humidifies the air. They do not have built-in climate control function. The amount of steam released is not controlled, which can lead to oversaturation with moisture.

Traditional humidifiers work on the simplest principle. Streams of dry air pass through a filter with water and come out humidified. Traditional models provide a humidity level of no more than 60%, so they are used only in residential areas.

The Boneco air washer combines the functions of a purifier and a humidifier. The models are simple and easy to use and consume little electricity. The system itself cleans the built-in disks from accumulated dust and debris.

Instructions for use

Place the device on a flat, dry surface and secure it in a stable position.

Direct the moisture outlet towards the center of the room, but in no case towards the wall, furniture, plants or people.

Do not install the humidifier on a hot surface, near heating devices or heat sources.
Before each use, check the amount of water in the tank and, if necessary, fill to the required mark.

Clean the tank to ensure long-term trouble-free operation.

Replace humidifier filters every 3 months, or more often if using hard water.

Combined air purifiers do not require filter replacement, unlike devices that exclusively humidify the air.

How to choose

Focus not only on the popularity of the manufacturer’s brand and appearance. First of all, pay attention to the technical parameters.

Limiting the maximum humidity level. If you plan to use a humidifier at home, models with restrictions will be sufficient. The humidity level in home premises does not exceed 60%. If the device is needed for premises for other purposes, a more functional model is needed.

Power varies depending on the type of device. The maximum power of ultrasonic humidifiers is 50 W, in steam humidifiers - 600 W. The power of the device is adjusted to the area of ​​the room to achieve the desired effect.

Water tank volume. The more water is placed in the tank, the longer the continuous operation lasts.

The touch display is usually built into models with more functions.

The built-in hygrostat will allow the device to independently measure the level of humidity in the room.

The dimensions can be impressive, but at the same time a small water tank reduces productivity.

Review the technical specifications to ensure they meet your requirements.

Some models humidify the air and scent it with essential oils. To do this, simply pour a few drops of oil into the aroma capsule and they will begin to evaporate along with the moisture.

Review of the best representatives

Ultrasonic air cleaner Boneco. The warm steam function heats the water to 80° before hitting the ultrasonic membrane. Mechanical control provides for regulation of the intensity of humidification and optimal steam saturation. The average price is 11 thousand rubles.

Ultrasonic model with mirror display and touch control. Humidifies the air with heated steam, and the built-in hygrostat controls the moisture level in the room. Cost from 7 to 10 thousand rubles.

One of the most popular models. High functionality combined with a simple control system. Duration of operation at maximum productivity from 10 hours. If desired, use with aromatic oils. The average price is 4 thousand rubles.

The device with its miniature size is convenient to take on trips. Cost from 3 to 4 thousand rubles.

Having familiarized yourself with the possible parameters of Boneco air humidifiers, it is much easier to choose the ideal device that suits all requirements. Use it for its intended purpose and take proper care of the device to extend the period of purification of the atmosphere in the house.

Equipment for regulating microclimate parameters is less and less associated with large installations that are connected to utilities. Leading climate system development companies offer compact and at the same time efficient devices with convenient control tools. Such devices include the Boneco 7135 air humidifier, intended for domestic use. Despite its modest size and low energy consumption, the device effectively performs its function, focusing on the settings specified by the user.

How the humidifier works

The operation of the model is based on the principle of ultrasonic influence. The body of the device contains a membrane, the vibrations of which break the water into small drops. Further through the working chamber, a special Boneco 7135 fan circulates air, due to the flow of which a foggy cloud is formed. In this way, humidity levels are achieved that can exceed the natural level. In any case, the user can adjust the settings of the device, using it to maintain it. As the tank empties, the corresponding indicator will indicate the need for another refill.

An important feature of this humidifier model is the water disinfection technology. Often, to fill the container, users take ordinary tap water, which does not differ in the quality of its composition. Thanks to special filters, the Boneco 7135 humidifier also provides comprehensive purification of the aquatic environment from germs and bacteria.

Main characteristics of the device

In the line, this model occupies an average position in terms of technical indicators. The power of the device is 130 W, which is quite enough to serve residential premises with an area of ​​​​about 50-60 m 2. In regular operation, Boneco 7135 consumes 550 ml of water per hour. At the same time, the volume of the standard tank slightly exceeds this figure - 650 ml.

Despite its modest performance, the device quickly gains optimal operating power and quickly brings the parameters to the required values. The dimensions of the device are also quite modest - 35 x 38 x 22 cm. But it is not only the combination of compactness and functionality that the Boneco 7135 device attracts the attention of buyers. Reviews also emphasize the modern control system. The owner can set the operating parameters of the device to automatic control mode, saving himself from unnecessary hassle.

Instructions for use of the device

You can start working only after preparing the device for use. The device should be installed in a place away from heating equipment. However, it is not recommended to point the device’s spout at specific objects in order to intensively moisten them. Immediately before turning on, you should fill the tank with water, the temperature of which does not exceed 40 degrees. The functions are controlled through a panel with buttons, which is equipped with the Boneco 7135 humidifier. The instructions note that in normal misting modes, the device operates only until the user-specified humidity coefficient is reached. To maintain a constant generation mode, you should set the automatic operating format using the appropriate button. In addition, the operator has the option of heating the fog within a range, which is also set through user settings.

Care and maintenance instructions

The device, due to its electronic filling, independently determines the need for cleaning. So, if the letter “A” lights up on the display, this means that the device needs to be washed. Both the water tank and the Boneco 7135 tank should be cleaned. The instructions warn against using cleaning agents - the components of the device should be washed only with clean water. If during operation the fogging mode was used predominantly, then cleaning is recommended to be performed once a week. If the medium was also heated, then washing is done more often - twice a week. Filter cartridges should also be replaced regularly. In the average mode of operation of the humidifier, they are updated every month.

Features of the Boneco 7135 model

Despite the simplicity of its functionality, the device received many interesting technological additions. For example, a digital display with programmable control elements ensures high accuracy when setting the humidity level. At the same time, the tank indicator allows you to monitor the current volume of water and, if necessary, fill the tank. The Boneco 7135 model also includes many design additions. Thanks to the rotary evaporator, the user can adjust the direction of the steam. But, again, the instructions do not recommend placing the device close to other objects, especially plants. The features of the device include a system for handling liquid media. The fact is that water from the tank does not pass into the processing zone immediately, but after filtration. Including an additional purification stage allows you to create a healthier air environment. True, the popular system of ionization through filters is still absent in this modification.

Positive reviews about the model

Climate control equipment is traditionally criticized by users for high energy consumption and noisy operation. However, in this case the device is free from such shortcomings. Quiet operation, for example, was made possible thanks to the use of a special design with rubberized legs. As for the low energy consumption, it is due to the compact size and optimized operating principle of the device. But there are other advantages that the Boneco 7135 humidifier has. Reviews, in particular, indicate the absence of a specific white residue on furniture that remains after the work of other representatives of the segment. Such deposits are typical for humidifiers that work with water without prior preparation. In turn, the design from Boneco provides a separate stage of water purification, which rids the generated steam of foreign impurities.

Negative reviews

Despite all the advantages of the design, there are also unfortunate miscalculations in its execution. Users note inconvenience during the process of pouring water. To perform this operation, you need to remove the housing from the pan, turn it over, then unscrew the filter and fill the tank. The procedure is complicated by the fact that the component parts do not fit together perfectly and you have to adapt to the specific installation of the Boneco 7135. Reviews are also critical of the heating function. Some users note that it is not needed at all, while others testify that in reality it does not justify itself.

Conclusion

In the climate systems market, there is a division of products into two classes. One is characterized by multifunctionality, while the other involves a clear segmentation of devices by purpose. Household 7135 rather belongs to the second category, since it is focused on performing a specific task in regulating the microclimate. And this device copes with the function of increasing humidity adequately, although the very concept of specialized devices gives every reason for complete and effective work. This is due precisely to the fact that the device gets rid of the burden in the form of unnecessary functionality. However, in the case of modification 7135, it was not without auxiliary options in the form of heating and water purification. And if the function of increasing the air temperature was generally greeted by the consumer without enthusiasm, then filtration provided quite tangible benefits.

The use of electric air humidifiers benefits adults and children with diseases of the skin, respiratory system, allergic conditions, and makes it easier to care for house plants, wooden furniture and fancy interior items. The Boneco U7135 air humidifier is ideal for use both at home and in any other room due to its small dimensions, convenient design and extremely clear control panel.

Humidifier Boneco U7135

The air humidifier Boneco (Boneko) 7135 is intended for use in rooms up to 60 square meters. The device is very useful both in hot summer and in winter, when the air in the room is dried out by the heating system. With its help, you can avoid the spread of infection in the respiratory tract, drying out of home flowers, damage to furniture, parquet and interior items made of wood.

The peculiarity of the U7135 model is that its operating principle is based on ultrasound, that is, a membrane is installed inside this device that vibrates under the influence of ultrasonic vibrations and breaks the water into a cloud of fine water vapor.

Due to ultrasound, the humidifier operates almost silently and does not change the room temperature. The operating mode of the device includes the function of heating the steam produced, but most often consumers prefer cold humidification.

The volume of the humidifier's water tank is 6.5 liters; thanks to its removable design, liquid can be added to it quite easily. To prevent the proliferation of pathogenic microorganisms, the inside of the tank is coated with an antibacterial composition, which ensures the safety of long-term operation. The presence of a built-in hygrometer allows you to fully automate indoor air humidification: the hygrometer itself controls the programmed humidity level, adjusting the intensity of the steam supply.

The water tank is equipped with a replaceable filter, or cartridge, for additional disinfection of the liquid. The filler for the filter is an ion exchange resin; if desired, it can be equipped with an ionizing silver rod, which has bactericidal activity against more than fifty viruses and microbes.

The cartridge also softens water and prevents the spread of tap water salts throughout the room, which confirms the absence of a whitish coating on furniture and interior items after prolonged use. The cartridge should be changed every 2–3 months, and even earlier if you use very hard water. To warn of the need for timely replacement, a contamination sensor is provided.

Using the device

Thanks to its convenient design and clear liquid crystal control panel, even an elderly person can operate the device. Instructions for use (manual) are included with each device, and you must read it before using the device.

Device diagram

Before use, the device must be placed on a flat surface away from heating sources (including heated floors). Fill the water tank with clean, cold water at a temperature not exceeding 40 °C. Do not add any impurities - essential oils, herbal infusions, flavors, substances for additional softening and purification of water. Having placed the container on the stand, turn on the device and activate it using the switch button on the LCD screen. Next, set the desired parameters:

1. 1. The level of humidity in the room, after reaching which the device will automatically turn off. Customizable ranges 40–75%.
2. 2. Running time: ranges from 1 hour to 9 hours, or continuous mode can be selected.
3. 3. Regulation of evaporation rate.
4. 4. Turning on/off heating, which ensures heating of water to 80 °C, at which the steam temperature will be 40 °C.
5. 5. Automatic operating mode: provides the optimal combination of humidity level and room temperature.

The humidifier tank is cleaned once a week with running water without additional chemicals. Limescale deposits in the spray area are removed using products intended for this purpose, followed by thorough rinsing. The remaining spare parts should be wiped with a soft cloth; the use of solvents and glass cleaning agents is prohibited.

If suddenly the humidifier has low supply power or no steam at all, then most likely the problem is a clogged membrane or air filter located on the device stand (indicated by numbers 8 and 12 in the diagram). They must be carefully cleaned: treat the membrane with a brush, and rinse the filter thoroughly.

Devices that regulate the microclimate are becoming smaller and smaller; they do not need to be connected to serious engineering installations; the equipment is constantly becoming more compact and more functional. Companies that manufacture such devices offer customers devices that have convenient control tools and a large number of functions. Such equipment includes the popular air humidifier for home use Boneco 7135. The device has very compact dimensions and consumes a small amount of energy. The humidifier fully copes with its intended purpose.

How does the device work?

This model works on the principle of ultrasonic influence. Inside the humidifier there is a membrane that converts water into small droplets, and then, using a special fan, the air passes through the working chamber. Steam is generated in it and exits through a special hole into the room. Thanks to this, you can significantly increase the level of humidity in the room, which can be much higher than natural. But a flexible system of settings will help create the correct microclimate in the room.

There is a special indicator on the device that shows that there is little water left and needs to be added. Often people fill the device’s reservoir with ordinary tap water, which is of rather low quality; the Boneco 7135 air humidifier has special filters that purify the water. Thanks to this, only pure steam is released into the air, without harmful bacteria and germs.

Humidifier characteristics

Among the entire line of Boneco humidifiers, this model is the golden mean; it is not overloaded with functions, and at the same time has very good technical indicators. The device has a power of 130 W, which is quite enough to efficiently serve a room with an area of ​​up to 60 m2. At maximum load, the humidifier will consume 550 ml of water per hour. The capacity of the reservoir in the device is 650 ml.

Despite the low power of the device, it quickly reaches operating temperature. The desired result is achieved in the shortest possible time. Boneco 7135 has very small dimensions: 35x38x22 cm. But this device was liked by a large number of people not only for its small size and extensive functionality, but also for its convenient operation. There is an automatic regulation that determines the required power of the device, thanks to which the owner of the device deprives himself of any hassle of regulating the humidifier.

Operating instructions

Before starting the device, it is necessary to carry out some preparatory work, and only after completion can you turn on the Boneco 7135 air humidifier. The operating instructions state that it is prohibited to install the device near heating equipment or gas stoves.

It is not recommended to use the device to humidify specific objects; it is used for the room, not specific objects. Before starting, you need to fill the tank with water, but its temperature should not be higher than 40 degrees. The control panel has all the necessary buttons for convenient use of the Boneco Air-O-Swiss 7135.

When the user-specified humidity level is reached, the device turns off automatically. If there is a need to constantly maintain a certain level of humidity, then you should switch to the automatic operating mode, which the Boneco 7135 air humidifier has. The instructions also inform you that there is a mist heating function, which can be turned on by pressing the corresponding button on the control panel of the device.

Care and maintenance

Thanks to the electronic filling, this device can independently determine the need for cleaning. If the letter “A” appears on the display of the device, this means that the humidifier is dirty and requires cleaning.

It is necessary to rinse not only the water tank, but also the device reservoir. Do not clean parts of the device with detergents. The cleaning process occurs only with ordinary water and a sponge.

If the humidifier is often used only in misting mode, then cleaning should be performed no more than once every seven days. But when the device is also used to heat the environment, then in this case it is necessary to wash the parts of the humidifier every three days.

But you also need to remember about consumables. The cartridge for Boneco 7135 should be changed every month when actively using the humidifier.

Peculiarities

This device is quite simple to operate and use, however, despite its simplicity, there are a large number of different technological additions that allow you to accurately determine the level of environmental humidity. Also, the Boneco 7135 air humidifier monitors the water level in the tank and, if necessary, gives a signal about its shortage.

In addition to a large number of functions, this model also has design features, for example, there is a special rotating spout, thanks to which you can adjust the direction of the steam. But you should know that it is highly not recommended to direct steam at plants, household appliances and other objects.

Also, the features of Boneco 7135 include the fact that water from the tank enters the system through special filters, thanks to which only purified steam without harmful microorganisms enters the air. Unfortunately, the popular ionization system is not used in this device.

Product warranty

The humidifier has an official warranty from the manufacturer for 12 months from the date of purchase of the device. In case of detection of defects or malfunctions, a person has the right to free warranty repairs. But you need to understand that if the device has mechanical damage or there is no warranty card, the service center cannot make free repairs. A humidifier, like any other equipment, requires proper care and attention. Also, in the event of any type of malfunction, it is prohibited to disassemble the product yourself and attempt to make repairs, even if it is simple.

Positive Feedback

A large number of humidifier users criticize this technique for high energy consumption and noisy operation, but not in this case. Consumers leave positive reviews for its efficiency, since the Boneco 7135 at maximum load consumes only 130 W per hour - these are very decent figures. Thanks to the rubberized legs, the structure is stable and does not rattle, as happens with other manufacturers of climate control equipment.

Users also note that there is no white residue left on furniture and other household items that occurs with other humidifiers. All this is thanks to the filtration system; the water passes through a special filter, and only then does the steam enter the environment. Those who have been using the Boneco Air-O-Swiss 7135 for a long time leave positive reviews about the good service life and reliability of the device.

Negative reviews

Despite the large number of kind words about the humidifier, there are also those users who note mistakes in this model. The most common complaint people have is that pouring water into the tank is very inconvenient. To do this, you need to remove the housing, pull out the filter inside it, fill the tank with water and repeat the procedure, only in the opposite direction. On top of that, the parts of the device do not fit together perfectly, so you still need to get used to the design features. The Boneco 7135 ultrasonic humidifier has air heating, but people often complain that it does not justify itself, or simply that it is an unnecessary and unnecessary feature that only slightly increases the cost of this device.

Conclusion

By and large, all climate systems can be divided into two classes. The first one has a lot of different functions, which can sometimes be inappropriate. The second includes devices that have average functionality and are intended only for a specific task - to humidify the air. This model can be safely classified as second class. The device copes with its main task just fine, which is why many people choose the Boneco 7135 humidifier. The price of this model also pleasantly pleases a large number of buyers, it ranges from 8,000 to 11,000 rubles. By purchasing this device, a person receives a truly high-quality device for humidifying indoor air.