How to remove the old film from plastic windows. How to remove the film from plastic windows: effective techniques. Why the film is badly lagging behind plastic

Many users, faced with the problem of firmly "soldered" with PVC window film profile, hurry to experiment that it does not always end well. Especially in case of color windows, there is a risk of destroying them. As effectively and without deplorable consequences, remove the old protective film from plastic windows, the portal of the media window will tell.

All plastic windows go to the market with frames protected by the manufacturer with a self-adhesive film. According to the rules, the protective film must be deleted as soon as possible after the installation is completed, especially when PVC window is exposed to direct sunlight.

Why is it so difficult to remove the old protective film with PVC windows?

Unfortunately, it happens quite often that by the negligence of installers or the user itself, the protective film on the PVC profile can remain even for several years. In this case, when the hands reach before bringing new plastic windows in order, the user is waiting for an unpleasant surprise - it is almost impossible to remove the protective coating.

Remove the old window film from the profile of the plastic window is difficult, because it consists of two layers. The outer layer (transparent film) under the action of ultraviolet rays begins to peel and it is relatively easy to clean. But at the bottom there is a second layer of white plastic with the marked label - it is he who sticks out so much to the substrate.

Especially bad, the presence of an old film looks in the case of ancient profile, because the protective coating is usually used in white. Under the influence of UV rays, the film is subjected to vulcanization and very firmly sticks to the surface of PVC windows. At the same time, it becomes less durable and easy to break.

Some are trying to wash off the protective layer with gasoline, acetone or other solvents - it helps a little, but in parallel you can remove the wood texture, which is used to the lamination of the frame (white PVC windows, of course, are insured). Experts do not recommend exposing the surface of the color PVC profile too strong mechanical exposure (scraping or grinding), because it is very easy to damage the layer of lamination.

Eureka: There is a way to get rid of the old protective film!

Fortunately, there are several ways to get rid of the protective film, we suggest to consider one of them. This method is simple, effective and most importantly, will not destroy the plastic window. However, the procedure will take quite a lot of time and will require the use of a device with a steam cleaning function.

Such a device can be bought without problems, they are often sold in supermarkets. Please note that the package included a special hose, allowing you to fix the nozzle. The versions of this device often appear on sale, in which the pairs goes directly from the reservoir through the nozzle. In this case, it will be necessary to constantly hold the heater in the hands during cleaning, but it is soon it turns out that the heating of the film at the bottom of the frame is not possible in this case (the windowsill interferes).

The work begins with filling the purifier with water and connecting to the power grid. After a few minutes you can start the heating of a small section of the steam stream of the steam stream (keep the nozzle directly above the film or even touch it). Heat a small segment 1-2 cm across the entire width. If the window film is already too old and does not exfoliate, it will have to re-heat it (after cooling). At this time, you can heat the protective coating of the window from the other end.

To remove a protective film with a steam, shortly after heating a small area, you must try to separate the nail to separate the film from the substrate. It is necessary to do it carefully and slowly, across the entire width of the tape. This is the most important point. It is necessary to make a small piece of film spacked across the entire width. Then you can capture the end and slow (!) To tear off the film with a parallel ferry heating on top and bottom (at the points of contact with the substrate).

If the protective film begins to rush and its fragment does not leave, in this place you need to use nail and lead to a situation where it will be squeezed again across the entire width. After removing a sufficiently long fragment, cut off with it with scissors, leaving 2-3 cm so that it was for what to cling to to continue further cleaning the PVC profile.

After removing the protective layer on the surface of the window frame, white raid remains, which is quite difficult to wash off. And there is a proven method - you can use for this purpose a means for washing the glasses (for example, Mr. Muskul).

Buying new plastic windows, do not ignore the tips of the window company, which are clearly spelled out in the instruction manual, when it is worth removing a protective film with PVC profile. This will save you and time and money, and care nerves. In general, compliance with the manufacturer's recommendations is not only in this paragraph, but also all others, is the key to the impeccable type and durability of your plastic windows.

Repair is over, there are new windows on the windows, the builders led the openings in order. It would seem that you can safely wait for the winter to check whether PVC windows are good as they say about them. But you completely think that you got rid of all problems. All windows are covered with a protective layer, and you will have to handle it. On how to remove the film from the plastic window, if it is not removed, we will talk.

Why do you need this film?

Why are the masters that install PVC windows themselves do not dyate this film? The fact is that the installation of double-glazed repair is usually not ends, but only begins. After that, the repair of openings, and the whole room. In addition, glass can be scratched when transported and during installation. To avoid all these troubles, glue the protective material.

The instruction says that protection needs to be removed from plastic windows no later than ten days after installation. It is best to do so, because otherwise you will have to not remove it with a slight movement of your hand, but to decide a much more difficult question - how to tear off the film from plastic windows.

Important! It is necessary to remove not only the film, but also the adhesive layer, which always remains on the profile.

What is the film?

Before you think about how to remove the protective film with PVC windows, you need to know what you have to deal with. Then how to clean the cleaning methods will be easier. The protective material has:

• the outer layer, which is usually removed without difficulty;
• inner layer;
• adhesive strip, which is tightly attached to the profile.

Important! The inner layer is so capricious that melts even from the spring sun.

How to clean the plastic windows from the old film mechanically?

For a mechanical cleaning method you will need:

Option 1

Act you have to act very carefully, so as not to scratch the profile. The protective material is easier to get off if it should warm it. For this, you need a hairdryer - you can take both household, but better, if there is an industrial, which in some construction stores give hire. Prepare everything you need, proceed to work to remove the film from plastic windows:

1. War down the surface with a hairdryer to protect the protection. At the same time, the jet of hot air should not fall on PVC profile - it may be extremely sensitive to high temperature.
2. Patty the edge of the film is a sharp object - it should separate without difficulty.
3. Solvent remove the adhesive strip.

Important! It is necessary to removely remove the knife or blade evenly and quickly so that the material does not have time to cool. Otherwise, the result may be reverse, the film is not simply not taken, but it will stick even more.

Option 2.

This method is good if the windows overlook the shadow side. Make a soap solution, moisten the brush and centimeter behind the centimeter, wash the entire protective coating.

Important! Metal brush for such a job cannot be used.

Option 3.

Film with plastic windows can be removed using a conventional school elast. True, the process is time consuming, so in this way it is better to shoot small fragments remaining, for example, after removing the knife.

Option 4.

Perfectly removes such protective material construction scraper for cleaning ceramic and glass surfaces. You can buy this in a construction store.

Important! The advantage of this method - the scraper does not scratch plastic.

How to remove the film with a chemical way?

This method is more sparing than mechanical. Danger that you scratch your precious plastic is much smaller. In addition, with the help of solvents, it is even possible to remove thoroughly adhered fragments of the coating. There are many chemical ways, how to remove the film from plastic windows, if it is not removed.

For the procedure suitable:

• "Kosmofen";
• white Spirit;
• any other solvent.

Option 1

To remove protection, a special means of "Cosmofen" is simply perfect. You can buy it in the same company that puts you PVC windows. There are several varieties of this drug. It is best to buy it from those who put the windows, as the accompanying goods of a solid firm selects precisely for the material from which the main products are made.

Option 2.

Excellent means for cleaning PVC material - White spirit. But remember that it does not dissolve the film, but separates it from the window. Therefore, you need some sharp object, like a blade or knife:

1. Patty the edge of the protective coating.
2. Pour in the resulting clearance of White Spirit.
3. Remove the film.

Option 3.

You can try to use the solvent. The method is not very reliable, but sometimes gives good results. It is not suitable for a solvent, and it is better to test somewhere in a small area.

How to wash plastic windows?

After the protective coating is cleaned, the window is best washed. Soft detergents are suitable for cleaning the profile - do not forget to look at the labeling store. There are special means for washing such products, but are suitable for those designed for ceramic surfaces.

Important! Wash better not with a cloth, but a foam sponge.

Process procedure:

1. Will erase dust from the windowsill and window frames.
2. Make a detergent solution.
3. Zigzag movements wash the glass.
4. Wipe it with a soft cloth or blot paper.

Important! To give glass glitter, in completion, wash it with an aqueous solution of ammonia - a few drops of 1 liter. If you wash the windows for the winter, it is to warn me out and snowing the window, rinse it outside with brine.

How to remove a protective film with plastic windows

According to the manufacturer's recommendation, the protective tape from the plastic window must be removed, preferably, in the first 10 days after installation. Subsequently, it is easy to remove the film will not be able, since the properties of the adhesive will begin to change under the influence of heat and sunlight.

To solve the problem, you can invite masters from the cleaning company, which quickly and professionally clear the surface of the window from the stuck film. But with certain skills, you can try to remove it yourself, taking advantage of a special scraper for glass-ceramic and a construction hairdryer. You can donate the tape with the help of technical alcohol or scotch, if it is possible to tear it on pieces.

The purpose of the protective film on the window of plastic is to protect the surface of the block from possible scratches and contaminants. After delivery of the product, installation and execution of slopes, the film must be deleted.

It is best to do it right away, but it does not always succeed. But remove, even a strongly glued ribbon, it is necessary. It is worth trying several ways.

Heating of a film with a construction hairdryer

This is one of the simplest methods for removing an unnecessary film. If you warm the hairdryer of her surface, soften the body of the decent and managed to dry the glue, it will be easy to pick up the edge of the ribbon and raise a little. Then, to direct the stream of hot air under the film, and gradually pull it, gradually taking off from the window block. Thus, without breaks, you can remove the whole strip.

While working with a construction hairdryer, it is impossible to make hot air on the glass - it can burst from high temperature.

Mechanical cleaning scraper

If the film cannot be lifted due to the fact that it immediately begins to rush and crumble, it is worth using glass-ceramic cleaning scrapers or for paint removal, you can also work universal, but in all cases you should take a new blade, then the surface surface will be smoother. It is also necessary to pre-heat the old tape with a construction or ordinary hairdryer in turbo mode, a steam generator can be applied. The remnants of glue and films are easily scraped with a scraper, which is kept under the minimum angle to the surface.

Using Scotcha

Sometimes after cleaning, the adhesive pieces remain that could not be removed. In this case, a wide scotch is useful. At first it will be necessary to degrease the profile surface with detergents or alcohol. It is better to use the tough side of the sponge and wash everything thoroughly.

Then you need to wipe the surface dry, stick your tape and align with a cloth. An hour later, it needs to be removed. On its surfaces, the glued pieces of protective film will remain on its surface.

All attempts to remove the stuck pieces with blades or cleaning abrasive means, can damage the plastic profile. However, small scratches can be removed with white Cosmofen brand glue, which is otherwise called liquid plastic. Sometimes the German cleaning agent Fenosol S 10 can be helped, which has a small dissolving effect. It is applied to a cotton cloth and wipe the damaged surface. When using these drugs, it is necessary to comply with the security techniques and the rules for working with these substances specified by the manufacturer.

Special means for removing glue

When the remaining film needs to be removed, and there is no hair dryer in presence, then you should use the means to remove adhesive residues. The Universal American WD-40 aerosol agent, which has in its composition White Spirit, can help in this matter. The substance does not interact with the plastic, removes stickers and contamination from the glasses.

Other substances have more targeted applications and are used to remove scotch residues, adhesive contaminants from stickers. Among them is HG Sticker Remover - which completely removes stickers, self-adhesive ribbons, spots of oil and bitumen. As with all the chemicals of such a principle of operation, it is necessary to work with it very carefully, take care of children.

The use of HG Sticker Remover is simple, it is enough to beat a small corner on the sticking film and drop there a little liquid. Leave for a while, and then everything can be easily removed and wipe this place with a cloth.

The same ability to remove the remnants of the adhesive layer have "Solins", "Lavel Off", "Antiskotch" and others.

The remaining stains from glue on the profile can be removed using a cotton disk and White spirit. You can use the usual school eraser, but it will take a lot of time. And then you need to fully wash the window with warm soapy water.

Before applying any of the similar funds on the front surface of the window profile, it is necessary to check its action on a hidden area between the frames or near the seal. If the color of the frame has changed or yellowed, the structure of its upper layer has changed, then it is not worth applying this tool.

How to remove the protective film with alcohol

When the film cries into small pieces, to tear off that almost impossible from the surface, you can apply technical or medical alcohol to remove them. This requires a small pulverizer, and one that is used to moisturize the leaf of houseplants is suitable. It is necessary to fill the container with alcohol and spray it along the contaminated frame. A few minutes will only wipe the desired place with a rigid sponge or brush. You should not use metal brushes or washcloths for these purposes, as they damage plastic.

Spray alcohol must be carefully, you can not allow splashes into the eyes. At this point in the room there should be no children or pets.

If the repairs in the apartment are not yet completed, and the windows are already installed, then in order to avoid a problem with the removal of a protective film, it is better to immediately remove it. And before the installation of slopes, plastering walls, stagnation of wallpaper and painting, it is better to put the surface of plastic with painting scotch.

The listed methods for removing the shut-off protective film from the PVC windows are the most simple and not too expensive. But if there are many different contaminants on the windows for some reason, do not risk the appearance of these products, it is better to call specialists by a cleaning company.

Owners of plastic windows are often faced with such a question as laundering a protective film. Of course, to remove immediately after installing the window, it is much easier, but often the owners do not immediately spare it or at all forget about it.

However, the time comes when still protective material will have to be removed. Then the question arises how to remove the dried film from plastic windows?

Naturally, it is important not to damage the window during this process, and also I want to do everything as soon as possible and without too much effort. What can be done in this case? Effective methods exist, which means they can safely use.

But to successfully remove the protective film, you must first understand the essence of the problem in more detail. Then it will be much easier to solve it.

Causes of rigid sticks

Why do you need a film on metal-plastic profiles? Companies through its gluing ensure the integrity of the product during transportation and installation. On the one hand, it is good that such protection is pasted on the windows of plastic. However, as ordinary people then get rid of it? When the product is already in place and the protective layer is no longer needed.

Very often, windows change during the full repair of an apartment or at home. This means that after installing window PVC profiles, the thin film coating remains for some time until the repair is complete completely, and dry out.

A few weeks later, the film is stronger with plastic and practically merges with it. It's not easy to fight with the rich protective material.

Why a protective tape sticks stronger over time:

1. Unfair windows manufacturers typically save on some nuances. In their row, the glue, which is used for sizing a protective material. There is such an unusual pattern, the lower the quality of the adhesive used, the stronger it attaches the film to the window. In this case, there are only two options, it is either to remove the film layer immediately after the installation of a metal-plastic product, or more carefully choose the manufacturer's company.
2. The time of year, oddly enough, also very affects the stickiness of the protective tape. In winter and autumn, for example, a cold frame, glue as it turns and the adhesion of the film with minimizes. If, behind the window, the warm season, then the stickiness increases, and it is not easy to clean the profile.
3. If you have a sunny side, you can confidently say that already a week after mounting the window from PVC, the film sticks greatly, if it is not immediately removed. The fact is that under the action of constant heating from the sunlight, the protective tape is as if dissolved, connects to the adhesive mixture and is highly connected with plastic. And afterwards also dries. Therefore, make conclusions yourself, and it is better to immediately drive tapes with frames.

These are the main reasons why the film protective layer is difficult to delete even a month after installation. The whole essence is hidden in the adhesive composition. With him and you need to fight.

How to remove a protective film with plastic windows right? There are several ways. Choose individually most suitable for you.

Mechanical methods of liquidation

There are only two such methods. These are the most efficient and proven techniques.

Let's get acquainted with them in more detail:

1. Application scraper. If the question appeared how to remove the adhesive tape, then the scraper will help. In winter, of course, it is certainly better not to use this method, since the glue is saved dense, and score a protective layer without damage to the plastic will be difficult. But in summer, this is the best option, the protective coating should be removed well and quickly. The scraper is able to effectively cope with the adhesive adhesive composition on frames and glass packages. Depending on the duration of staying tape on the windows, it can be removed in different ways, small parts or large segments.
2. Stationery Scotch. How to tear off the film with PVC? Very simple, with the help of tape. The bottom line is that how the adhesive protective paper has already been said very thin, so it happens not to simply remove the solid ribbon. There will be an ordinary wide scotch for the rescue. It is tight, which means stronger than the window tape, in this and the whole point. Everything that will be needed is to simply stick tightly tape over the film, and then hand off it with it. Thin ribbons will easily remove and remain on the Scotch band.

All other methods are based on chemical impact. But there is still a heating technique, which is also considered good and simple. However, it also has its own nuances.

Removal by heating

How to remove a film from plastic windows? If you have a building hairdryer at home, it can be applied to quickly remove the old protective film from the metal-plastic window. You can also try to use a household steam generator. The main meaning is to melt the adhesive layer between the film and the surface of the window, so that the tape will be free.

The following points must be taken into account:

• it is not worth heating much, since the ribbon can melt, then the task is only complicated;
• after warming up, it is necessary to first give the window to cool;
• it is not worth a hurry, otherwise the tape will remove unevenly;
• too close to keep the hair dryer is impossible;
• hot air should be directed not on a plastic profile, but on the glass.

If you comply with all the recommendations and produce the procedure correctly, it will not take off the sticky protective safety paper. It will be enough to just pry the edge of the ribbon with a knife or scraper, and then remove the coating with a solid piece without interrupting.

Chemical removal method

Remove the film from plastic windows by chemistry. At the heart of such methods for removing the protective coating with profiles, chemicals are chemical. They are able to dissolve sticky material, which will then be easily disconnected, and then it can be simply washed.

So, you can apply such cleaning products:

• Shumanitis;
• Antskhotch;
• MELLERUD;
• Label off;
• composition of RP-6;
• composition WD-40.

All these tools will come to help to spare old stickers, tape and wash off glue spots with PVC windows, and also help remove the old paint. They are perfectly able to rub the protective tapes on profiles, while completely without damaging the plastic surface.

If after removing the film, traces of glue remained, then they should be completely lined, so as not to stick dust. You can use to remove the White alcohol or acetone. And also try to clean the stains of the stationery.

Liquidation of the sunscreen layer

Another fairly widespread question that concerns not only plastic, but also wooden products, is it how to remove the sunscreen film from the window? Is it possible to tear it at all? Yes, naturally it is real. However, all kinds of severe solvent substances are inappropriate to remove the film. What to wash the glasses in this case? It will be enough for an ordinary knife and soap solution, or you can use noise.

Immediately it is worth saying that it will not be so easy to remove protection from the sun. But if you spend some time and make efforts, everything will turn out.

How to clean the glass of glass? It is desirable to slightly warm the surface of the glass with a hairdryer before starting work. Next, we carefully wipe the window with soap solution and proceed to the removal of the coating. The glue will gradually dissolve, and the protective canvas, tearing, will have to gently approach the scraper.

Finally, the double-glazed glass filter and the frame launders the glasses for washing the glass. If scratches were found on plastic after the work done, Kosmofen comes to the rescue. However, it should be carefully examined by the instructions.

Here are so simple ways to clean the windows on the windows. The main thing to do everything in no hurry and carefully. Then the result will be excellent, and no trace or defects will defect.

Plastic windows are often equipped with various films, which are needed to protect against the sun, giving glass greater strength, decoration. When buying an apartment, the windows can be covered by such films, but they are not always needed by the new owner. In addition, if it is time to update the windows, since the films have a property of coming in disrepair, the question arises how to remove the sunscreen film from the window.

Methods of removal of coating

You can remove the sunscreen film from the glass in different ways by selecting the most convenient and affordable. This is done and mechanically, and with the help of various detergents, also use a combined approach in order to clean well.

The film can be quite useful: it has a small thickness, while makes the window much stronger, it will not be able to smash a simple stone. There are different types of films that help protect the glass even from a strong impact, such as a shot; They are attributed to the class of protective. Remove the perforated film from glass or any other type of protective or toning variety from the outside will not work: an attacker will not deal with it, as the process requires a lot of time, attracts attention to others. Most films are pasted on the inside, with the exception of protective.

Know how to remove the film from the glass window, it may be necessary if you want to replace it when updating the interior, the replacement of the glass package. Sometimes the product loses the external attractiveness and requires the update or home of the premises want to change its illumination, make the room lighter or darker. The process of removal of the film is simple, does not require hiring a specialist, but it is worth considering that you will have to spend this enough time and strength. It is necessary to work carefully: in the process it is easy to damage the glass, apply scratches on it, especially if you remove the film with the help of rigid materials like a spatula or a rough brush.

What do you need to do when you want to remove the film from the window?

Choosing a method, a means, a glass cleaning option, the room owners come from several parameters:

• It is necessary not to cause glass harm.
• If possible, to spend at least time.
• The option must do inexpensively.
• On the glass should not be traces of glue, remnants of the film, various contaminants.

The easiest option than to clean the glass from the sunscreen is a spatula and fingers. Some types can be carefully pushed, taking to tear off the edge, but it turns out not always due to the fact that the film is unevenly punctured, there are damage and lay.

Remove glue from film from glass is quite difficult. It is poorly removed by detergent, not amenable to mechanical effects. In order to remove it, you can use the White spirit or other alcohol-containing substance that can gently clean the surface. It is not necessary to use a rag with a rough pile, since because of it on the glass can remain noticeable in the sun.

Understand , how to remove an old film from plastic windows, it may be necessary when damaged, desire to change the appearance of the window, update the old coating that has managed to spoil.

What methods for dismantling exist?

Removal methods can be divided into two - mechanical and chemical. The first allows you to remove the film from plastic windows without much cash, but with risk to scratch the glass. The second will take more time, it is more expensive, but with properly selected tools, you can thoroughly clean the surface without causing it harm. For greater efficiency, the ways are best combined: for a start, it will be necessary to break the entire swollen film, cracked or otherwise spoiled film.

It can be removed with plastic windows with hands, then get rid of glue using substances such as Cosmofen 10, Fenosol. These detergents have a cheaper analogue that you can buy in a shopping store: it is called P-12.

Remove the protective film from plastic windows will be much easier if you can crawl it, you will warm it up with a construction dryer. Preheated glue becomes more damping and allows you to disconnect parts of the structure. However, the glue itself is better to clean up when it will cool down a little.

The surface must be worked out evenly: the better you do, the easier it will be to remove the self-adhesive film from the glass and the remains of its glue. The latter will not be easy to remove, you will need to use the solvent, scraper and detergents. It is necessary to act carefully, otherwise you can scratch the glass. A steam generator can help in this business. With it, you can remove the stained glass with glass , get rid of tinting or protective film, glue residues. If there is no steam generator or a powerful hair dryer at hand, do not try to warm it up with an iron. So the film does not take off, but partially sticks to the surface of the iron, which can spoil it to a large extent, and after cooling it, it will not be easy to tear it from iron.

Remove the self-adhesive film from the glass if it is well heatled, you can, using hard eraser for artists. Rests of elasty are removed from the window easily. For this you need a dry sponge or rag. If glue remains, you can apply the eraser again or use the solvent. In most household stores there is a remote film from the glass.

Before removing the film from the glass, you need to carefully examine all the ways, to purchase suitable detergents and tools, with which you can clean the surface.