How to paint paintable wallpaper without streaks. Wallpaper for painting - design ideas for creating a stylish interior (112 photos) Wallpaper for painting tips

Tool: roller with fur coat; paint tray with squeezing mesh; brush - 50–80 mm flutes; slightly sticky paper tape.

The choice of roller affects the quality of painting sometimes more than the paint itself. For painting the entire wallpaper, the best result is achieved with a long-nap roller. Long pile reaches to the "bottom" of the embossed wallpaper pattern, short pile paints only the "top" of the pattern. Foam rollers are not suitable for painting, they press air bubbles into the paint layer, which reduce the quality of painting. However, these rollers can be used to remove paint from the "top" of drawings. The velor fur coat takes little paint, and the roller itself does not fall through to the "bottom" of the drawings, with such a tool you can paint the top of the wallpaper relief.

To paint the corners, narrow brushes are used - flutes or short (up to 50 mm) rollers.

Preparation for staining. Line and cover floors, window sills and radiators with old newspaper or plastic wrap. Glue the baseboards (if not removed) and the expanded polystyrene cornice with paper tape, wrap the heating pipes - we don't need to paint the pipes yet. The paint under the paper tape does not drip, and it itself is easily removed and does not leave marks. Remove the tape after the paint thickens, but without waiting for it to dry completely.

For a good covering paint, as a rule, it is expensive, one layer of paint is enough, with a cheaper paint two layers are made. It is not very important whether it is imported paint or domestic, as long as it is real and not fake.

Coloring wallpaper. Follow the recommendations on the paint can. Each new coat of paint should only be applied after the previous coat has completely dried. During long breaks in work, the wall must be free of dust. If the manufacturer recommends thinning the paint to the desired thickness, usually adding 5-10% water, pour the paint into a bucket and add water. If you do not need to dilute the paint, then simply mix it with a mixer or a wooden spatula. Strain the paint through a nylon stocking into a separate bowl. Close the unused paint in the jar tightly with a lid, turn the jar over for a few seconds so that the paint inside the jar clogs possible holes and put the jar in storage.

First, you need to paint the upper and lower parts of the walls, along the ceiling and floor, and the corners of the walls with stripes about 100 mm wide with a flat brush or a special narrow roller, so that the edge of the roller does not stain the corner or frieze. We paint not the entire perimeter of the wall, but in parts, in order to observe the basic rule of the painter: "the rule of the wet edge". When we apply paint, it begins to dry out, if we let it dry, then by applying new paint and partially overlapping the painted one, we get two layers of paint at the intersection. They are thicker than a single layer and interlayering will stand out against the main background as a spot. If the painted edge of the first strip has not yet dried, but has already thickened, then by applying paint next to this edge and “going” onto it with a roller or brush, the tool “lifts” the old paint with separation from the painting surface. In order for the paint to lay down evenly, without stains of a more saturated color and not "wrap" on the roller (brush), you need to apply a fresh strip of paint in time, mixing it with the old one - "along the wet edge". Therefore, it is impractical to draw stripes around the entire perimeter of the walls at once, you simply will not have time to “roll up” the entire wall with a roller before the paint in the stripes begins to dry. It is best to tint the corners, where the sockets and switches are attached - and other places where the roller cannot be rolled - as you move towards these places. You need to paint one wall after another one by one, if you are working together, then you can paint two walls at once, starting from the corner. You need to work without interruption until you completely paint one wall. Then you can rest and paint the next one, again without interruption.

Work with a new roller or change to an old fur coat. Soak a new roller coat in warm soapy water, wring it out and rinse it again with clean water - the goal is to remove the loose fibers. We take a roller and dip it in a trough (specially sold for working with a roller) with paint, do not dip it into the paint completely, but dip it. Usually the roller gets wet on one side, but the other side cannot be turned in any way - the wet edge becomes heavier. In order to moisten the roller from all sides, roll it out on the grid of a trough or on a clean sheet of linoleum, hardboard, etc. Just not along the wall! You may need to dip the roller in the paint again and roll it out again. You need to roll it out until the roller coat is completely saturated with paint - the roller will begin to "chomp". As the painting work progresses, this operation is repeated with each set of paint.

If you start painting the wall without even filling the roller with paint, you will get unpainted, which, after drying, will give stains. Therefore, before each lifting of the roller on the wall, it is imperative to ensure that it is evenly filled with paint. Experienced painters do it automatically, but for now you need to practice. This technique is learned quickly.

Next, we lift the paint onto the wall with a roller and roll it out evenly. Precisely evenly so that the paint layer is the same thickness. Roller movement on the wall resembles drawing a huge W, stretched up and narrowed at the sides. The last roller movement should be directed from the bottom up, this will not allow a thicker layer of paint to accumulate at the bottom of the wall. Without picking up paint on the roller, turn it perpendicular to the layers of applied paint and shade them (fig. 114). We drew one letter and shaded it, draw another under it, without tearing off the roller and partially overlapping the painted one, do not forget about the “wet edge” rule. The paint is applied to the walls in vertical parallel stripes, from ceiling to floor, approximately 700 mm wide. The width of the strip may be narrower, the main thing is that the edge of the paint on the strip does not have time to dry, on which the roller will "run in" when painting the next strip.

Rice. 114. Painting the wall with a roller

In order for the paint not to have time to dry out at the edges of the stripes, a simple technique is used by painters. Before starting work with water-based paints, the humidity in the room is raised. To do this, half an hour before painting, a basin of hot water is brought into the room, the windows and doors are tightly closed, and the heating radiator is closed with a damp cloth. This increase in the relative humidity of the air allows walls to be painted in almost any sequence. The walls are painted without fear of premature drying of the paint and it lies on the base in an even layer. At the end of the work, the basin of water is taken out, and the doors and the radiator are opened. The humidity in the room gradually decreases and the paint dries up. However, it is important not to "overdo it" with an increase in humidity, do not forget that our wallpapers are glued on water-soluble adhesives - they can fall off.

Having finished painting the wallpaper with the first layer, the paint is allowed to dry and, if necessary, paint it with a second layer only with vertical strokes, and then, after the second layer has completely dried, with a third layer, a velor roller, highlighting the pattern. The corners are painted over with short rollers or, which is much more difficult, with flutes, without "sinking" the brush into the relief of the drawing. If a technology is used with the removal of paint from the top of the embossed pattern, then the paint, without waiting for drying, is removed with a foam roller with frequent squeezing and washing the foam coat.

At the end of the work, the rest of the paint is filtered through a nylon stocking. The roller, if they are still supposed to work with the same paint, does not need to be washed. It should be wrapped in a clean, damp cloth and packed in two or three plastic bags. Roller washing - paint overruns, it should be washed only after completion of work.

For subsequent repairs, the wallpaper can be painted as many times as the drawing allows. The last color completely evens out the relief of the wallpaper.

Wallpaper for painting is becoming more and more popular today. The advantages of this method of wall decoration are exclusivity, a simple technique, the ability to hide minor surface defects, high wear resistance and design variability.

Many homeowners are interested in how to paint wallpaper for painting. However, the technique is feasible even for beginners. First, you need to decide what kind of wallpaper materials to choose and what paint should be used.

Wallpaper for painting is a great option for design room decoration.

Varieties of wallpaper and their features

Several types of wallpaper can be used for painting. Each type of wallpaper has its own characteristics, advantages and disadvantages. Let's take a quick look at each of them:

1. Light paper wallpaper - this type of material, as a rule, has a relief structure and impregnation from a water-repellent composition. This allows you to apply paint over the canvas in several layers and not be afraid that the wallpaper will warp or bubbles will appear. Paper rolls are affordable, completely eco-friendly and easily stick to wall surfaces. In addition, these wallpapers can be used to decorate the ceiling. Among the disadvantages is the sensitivity to mechanical damage.

2.Glass fiber wallpaper. This type of material is distinguished by high strength and durability of operation, since quartz threads are used at the basis of the cloth. Painting glass material is more time consuming than working with paper, but it allows you to create an imitation of various textures.

3.Linkrust is a material that contains only natural materials. In the manufacture of such wallpaper, a composition of chalk, linseed oil, wood flour, rosin and beeswax is applied to a paper base. Such a coating lasts long enough, has high aesthetic characteristics, but a high cost.

4. Non-woven wallpaper is the most popular option. They are easily glued to the wall, allow you to repaint the surface several times, and also effectively hide irregularities. In addition, they can be cleaned with a damp cloth. At a cost, they are somewhat more expensive than paper ones, but their service life is twice as long.

The general features of using wallpaper for painting include such aspects as: good sound insulation of the room, creating a cozy atmosphere, variability of design ideas, protection of walls from damage. The texture of wallpaper materials for subsequent painting can be either monotonous or with a chaotic pattern - it all depends on the general concept of the interior.

With the help of various textures of the wallpaper, you can create an original interior of the room.

Tips for choosing paintable wallpaper are presented in the video:

Choice of paint

The next task before starting the renovation is the choice of paint. The type of coloring material will determine the durability, wear resistance and external aesthetics of the finish. So, the main types of wallpaper paint include the following materials:

1. Water-based paint is the most common and affordable option. Dyes can be matte, semi-matte and glossy. Matte paints perfectly hide roughness and minor surface defects, and glossy ones emphasize the texture of the walls, forming a durable and beautiful coating.

Water-based compositions allow you to choose any shade of color. The peculiarity of their application is to perfectly match the color of the paint. Therefore, before applying to the entire surface of the walls, it is advisable to make test strokes on a small area. After making sure that the properties of the paint meet the requirements, you can proceed to the complete painting of the walls.

2. The latex dispersion-based compound is an environmentally friendly and safe material. However, it dries quickly enough after the package has been depressurized (2-3 hours). Such a substance must be diluted with water and immediately start painting the walls. It is also worth considering that the surface will dry within 3 days.

3. Alkyd paints are intended for painting those surfaces that are subject to mechanical damage and wear out quickly. The main advantage of such a composition is that after painting, brush marks are completely invisible on the wall. However, in terms of cost, such paints significantly exceed the previous options. They are also flammable, which limits the scope of their application.

Each type of coloring composition has its own characteristics that must be taken into account before repairing.

Tinting technique

The modern construction market offers a lot of color variations of paints, but not all factory colors allow homeowners' design ideas to come true. In this case, you can purchase a classic white wallpaper paint and tint it to the desired tone. There are two methods for this:

1.Hand tinting is a completely unpretentious process. It is enough to acquire the desired pigment and by increasing the concentration in the dye composition to achieve the optimal color. The more pigment, the richer the final shade.

Important! After drying on the surface, the shade becomes lighter. To achieve the desired brightness, it is recommended to make the composition 1 shade darker or to carry out a series of test tinting on wallpaper fragments.

2. Computer tinting is a new service that involves digital modeling of the desired shade. The computer will calculate the exact amount of pigment that needs to be added to obtain a particular tone after the walls are dry.

Tinting of the dye composition will allow you to create the optimal shade for the author's design.

Master class on painting wallpaper in green:

Instructions for gluing and decorative painting of wallpaper:

Choosing a brush and roller for work

Choosing the right tool sometimes affects the final result more than the paint itself. For wallpaper, a roller with a long pile is considered the best option. Such a coating of the roller allows you to carefully paint over the smallest cavities and texture of the canvas.

It is strongly not recommended to use a foam roller for coloring the wallpaper. In the process, he presses small air bubbles into the paint layer, which will negatively affect the quality of the wall painting. However, it is precisely such a tool that is most suitable for removing excess composition from the top of the picture.

Velor rollers are suitable for painting the relief of wallpaper, but not for full painting of the canvas, since it takes little paint and does not reach the “bottom” of the texture well.

Important! To paint the corners of the room, you should use special narrow brushes - flutes. Short rollers (up to 50 mm) are also suitable.

A competent choice of roller and brush is a guarantee of high-quality painting of the walls.

Wallpaper painting technique

Before you start the process of painting the wallpaper, you need to prepare the following tools:

long pile roller;
paint brush 4-5 cm wide;
masking tape;
coloring composition;
container for paint;
mixer for stirring.

Important! The main rule is to apply the coloring material only on a dry surface. Therefore, it is impossible to paint on wallpaper earlier than 2-3 days after gluing them.

The very method of work is performed in the following sequence:

1. Initially, you need to prepare the paint - dilute it in the desired consistency and color. The finished composition should be homogeneous, without additional inclusions.

2. Then, using masking tape, you should paste over the skirting boards and the places where the walls meet the ceiling. Scotch tape covers all elements that should not get paint.

4.First of all, you need to process the corners using a brush.

5. Then the coloring agent can be applied to the entire wallpaper. This must be done from top to bottom. This approach allows you to make the color uniform and avoid the formation of streaks.

6.Application of paint should take place in an even layer, carefully rolling the roller along the wall. Gaps are not allowed, even if multi-layer painting is planned.

The wallpaper painting technique is quite simple and allows you to create the most interesting design solutions.

Decorating walls is a fairly meticulous work that requires a responsible approach. Wallpaper for painting is a fairly affordable and practical finishing option, however, in order to obtain an effective result, you should carefully consider the choice of paint and tools.

Features of painting with a textured roller are presented in the video:

Wallpaper for painting is a dream of any designer, a discovery for a builder and a godsend for many owners. These coatings make all subsequent renovation work an easy task, which does not require a lot of money and time, because they can be painted many times without complicated surface preparation.

Peculiarities

For many reasons, more and more people decide to glue wallpaper that can be repainted in the future. Such repairs are now at their peak of popularity. There is nothing surprising in the fact that this particular decorative material became the hero of our conversation. Why is it worth sticking wallpaper in the room intended for coloring:

increasing sound insulation;
creating a cozy atmosphere;

a large selection of design solutions that can be implemented;
the organization of a protective coating on the wall;
a wide range of textured solutions.

How many times can you repaint?

An important advantage that is characteristic of such wallpapers is multiple painting. The number of stains may vary within 10-15 times.

It is not recommended to paint a coating with a pronounced embossed pattern too often. The drawing with each coloring will be smoothed and nothing may remain from the relief.

Smooth wallpaper and fine textured coating are better tolerated by repeated staining. The material itself in both cases will not suffer from frequent staining.

What are the varieties?

Not all wallpapers can be used for coloring - everyone should understand this well. Even those canvases that are intended for coloring are significantly different. The choice must be approached consciously, with knowledge of the matter. We will tell you what the names of such materials are, what features you need to focus on, as well as introduce you to the distinctive characteristics and reveal important secrets. Let's consider in detail what kind of wallpaper can be used for coloring:

Paper wallpaper attracts with its affordability, so many choose this option for applying pigment. This decision has the right to life, but only if two-layer wallpaper is chosen. Due to its high strength and reliability, the decorative material will be able to withstand the staining process. It is not worth conducting such experiments with single-layer materials, so that you do not have to re-glue the walls later.

Liquid wallpaper can be painted, but you need to carefully select the color and be able to combine different shades. The main problem is the transmission of the color of the material through the pigment layer. Applying paint with a thick layer is not a worthy solution, since in this case the texture of liquid canvases will be hidden, and the walls will be ordinary, even.
Vinyl Although the materials are created on a paper basis, they are more durable than simple wallpaper. They tolerate the application of the pigment much better. The range of vinyl materials includes a category of washable models. It is categorically impossible to paint such wallpaper, since it will not be possible to obtain a normal result. The paint will not absorb or even linger on the surface, so streaks and streaks will result.

Options n and non-woven base are best suited for changing color by applying pigment, which is why they are most often chosen. Moreover, surfaces with such a finish can be repainted several times - the wallpaper will not be negatively affected. Even old non-woven fabrics can be simply repainted, which allows significant savings in repair costs.
Glass fiber- another good option for our case. But they are less likely to become the user's choice, since they have a high cost. But their reliability and durability justify all the costs. This type of coating is created specifically for coloring.

Special wallpaper designed for painting outperforms conventional decorative materials.

They can be used as a ceiling decoration, and they are available in a large assortment: simple, ceiling, vertical, exclusive, with different sets of characteristics, textured.

What to glue on?

The process of pasting wallpaper determines the success of the whole venture, therefore, this process must be approached responsibly, adhere to the technology and adhere to the rules. The gluing technology differs depending on the selected type of wallpaper. In order not to worry if the wallpaper will stick well to the surface, these application rules must be followed:

Paper sheets do not need impregnation, the adhesive is applied directly to them.
In the case of vinyl wallpaper, which has a paper backing, impregnation is necessary. The adhesive is applied over the sheets and left to absorb for the time specified by the manufacturer.
Glass fiber does not need to be spread with glue. They are applied dry to the wall and the glue is applied to the surface.

In order for the wallpaper to stick to the walls efficiently and firmly, you need to learn how to choose glue. In this matter, it is worth focusing on the weight and density of the canvases:

Lightweight paper wallpapers can be glued with a composition that is designed for lightweight fabrics. It is based on methylcellulose.
Heavy wallpaper will not stick to this composition. They will require a more reliable and durable adhesive material. For example, PVA-based glue.
A special composition is designed to work with glass fiber.
Wallpaper can be glued to water-based paint, but only non-woven. First, you need to conduct an experiment on a small piece of canvas. If it adheres well, then you can use a similar method for the rest of the surface.

You also need to familiarize yourself with some of the intricacies of gluing wallpaper for painting, which will allow you to get the perfect result:

The base does not need to be carefully leveled. Of course, large irregularities will have to be eliminated, but minor flaws can be left. Moreover, it is permissible to choose a semi-matt paint that will hide the existing shortcomings. The surface must be in the same color so that the new finish can be applied evenly.
The old water-based paint coating does not need to be removed as it provides a good base for a new finish.
Water-based paint can also be left on.

Do not apply a new decorative layer to the oil paint. It will have to be completely removed from the surface.
If there is a pattern on the wallpaper, then the length of the canvases will have to be made 5 cm longer. This stock will allow you to combine the coatings and make the drawing solid. Wallpaper that will be covered with paint in the future must be glued to the joint. If there are overlapping spots, the paint will highlight even more and focus on these shortcomings.

How to paint?

If the choice is made incorrectly, then the wall decorative layer will not be strong enough, beautiful, durable and resistant to external factors.

The following paint is presented on the construction market.

Water based

Such compositions are leading in terms of sales. It is easy to work with them, they are inexpensive, the assortment is impressive, including not only colors, but also texture (matte, glossy). Matte compounds look attractive on the wall and are able to hide minor surface imperfections.

Gloss looks more solemn but it should be applied exclusively on an ideal wall that does not have the slightest flaw... With water-based dyes, you can easily select the desired color. To accurately guess the desired shade, you need to make test strokes and evaluate the result.

Dispersion latex

Such paints benefit from environmental friendliness and safety. Such a composition must be quickly consumed, since it dries up a few hours after opening the package. Although the painted surface will dry for about 3 days.

Magnetic

Not so long ago, the modern building materials market began to offer magnetic paint. Once applied, magnets will adhere to the surface. First of all, such a solution will be relevant when decorating children's rooms. In addition, in any other room, you can select a section of the wall for placing small decorative elements on it, which will be attached to magnets.

This paint is available in a limited range of colors, and even tinting is impossible. Let no color be added to such compositions, but a layer of decorative composition of the desired shade is easily applied over the dried magnetic paint.

Alkyd

Such paints are expensive, but reliable and durable. Such compositions cover walls that are in intensive use and are subject to rapid wear.

Alkyd compounds are topical for use in retail outlets, public places and production workshops.

The paint can be applied with a brush. In this case, there will be no traces from such a tool on the dry surface. This paint is heat-sensitive and even flammable, which should be taken into account when carrying out repairs.

Acrylic

Acrylic compounds are no less popular than the materials described above. The assortment of such paints is huge, from the area of use (for facade work or interior) and ending with various textures.

Oil

Such compositions cannot be used for dyeing wallpaper. Paints with solvents are especially prohibited. Such substances negatively affect the wallpaper.

The choice of paint should also be based on the type of wallpaper that is applied to the walls. This point is important, because everyone wants to get a high-quality and durable result:

It is better to process paper materials and fiberglass with latex compounds, which do not have a pronounced effect on the substrate. Also, water-based paints are well suited for wallpaper with a paper base.

For non-woven wallpaper, you can choose latex compositions or use acrylic paint. The latter option is more affordable. Experienced builders cover the painted surface with varnish, due to which the decorative coating becomes moisture resistant and impervious to conditions of intensive use. After such treatment, re-staining becomes impossible.
Acrylic compounds are intended for vinyl canvases.

If you plan to make a textured surface, then multilayer staining cannot be used. In this case, the texture of the wallpaper will be smoothed. Coloring materials are selected for painting the canvases on the ceiling, the principle does not change. No matter what material you choose, you need to choose high-quality coloring compositions. The desire to save money can lead to negative consequences, and the result will be far from expected.

Color solutions

The use of color schemes when painting wallpaper is a popular trend that is actively used by experienced builders and beginners. To obtain the desired shade, the color is added to white water-based paint or mixed with acrylic compositions.

Color is a rich pigment that allows you to change the shade of liquid wallpaper and coloring composition for finishing paintings.

It will be difficult for an inexperienced person to work with these formulations, but still such a process is quite doable. You will have to spend a lot of time until you get the desired shade.

Feel free to experiment. First you need to take a small amount of paint and add color in portions. As soon as the desired combination is obtained, you can take up a large volume of coloring material. The shade should be constantly checked on an unnecessary section of the canvas. In this case, you can clearly see the future result.

If you don't want to experiment, take risks and spend time looking for the perfect shade, you can use the computer tinting service. A special program will carry out accurate calculations and give out the right amount of color scheme, which will allow you to get the desired shade.

In order for the room to be not only original, but also harmonious, it is necessary to carefully consider the future interior. Everything matters: the pattern on the wallpaper, its texture and shade. The market for such coatings is overcrowded, so you can easily find a suitable option that will embody all the wishes of consumers. Think carefully about the texture of the decorative coating: your wallpaper will be with a pattern, or a smooth surface will be more successful. Textured wallpaper can be with flowers, with imitation of brick, masonry, with a geometric pattern.

When choosing a shade, you need to focus on the type of room and the features of its use:

Children's room requires a choice of pastel and calm shades. For girls, you can choose peach, pink, beige, cream paints. For boys, blue is more suitable, although many tones are universal. Children's dreams come true in a new type of wallpaper. They are embossed, made in the form of a large coloring. For a little artist, such a solution will most of all be to his taste, because he himself will be able to take care of the design of his room. The main thing is that there are always bright, colored paints at hand.

For registration office space wallpapers that imitate natural materials are often chosen. In this case, bright and dark shades are excluded, for example, red walls will not create the necessary, working atmosphere.
To the bedroom you can choose smooth wallpaper, and decorative, small texture is also allowed. For tinting, it is better to choose pastel colors, although dark shades can look beautiful if a decent ensemble of colors is created.

For registration bathroom voluminous textures in wallpaper and dark tones in color are well suited. If visual expansion is required, coatings with a small white pattern should be used.
Living rooms give free rein to fantasy. Here you can embody bold ideas, for example, combine two colors. If one wall is painted in one shade, and the other surface is painted in another, then the space will visually expand, and the room can be divided into functional zones. Combined, with a sense of style and tact, you need to choose colors so that they match with each other and create the right atmosphere.

The existence of different paint application technologies allows different results to be obtained. For example, if you apply paint to the inside of the canvas, the shade will turn out to be soft and unusual. It is also possible to combine two colors on embossed surfaces. To do this, you need to apply one layer, wash it off the protruding pattern and paint it in a different color using a foam roller.

Wallpaper for painting is a designer's dream. With them, you can create original interiors, embody bold ideas and repaint walls with minimal investment.

Work order

You can paint the wallpaper with your own hands in the apartment. Moreover, it is quite simple. The whole process is described below, it is broken down into several stages. Stick to this plan and the coloring of the wallpaper after gluing will go as smoothly as possible. The coloring layer can be applied only on a well-dried surface... First, gluing follows, then the surface is left for several days to dry. Only after that you can proceed to staining.

Surface preparation

At this stage, you will need to clean the work surface, protect the floor, windows, heating system elements from possible drops of the coloring composition. The surface must be free of contamination and pathogens. The wall should be not only clean but also dry. Consider that not all wallpapers can survive wet cleaning. The skirting boards and the places where the walls meet the ceiling must be protected with masking tape.

Before sticking wallpaper, you need to turn off the power supply, dismantle sockets, switches and cover the wires with polyethylene.

Primer

It is imperative to prime the wallpaper before it is painted. This processing technology will reduce paint consumption, reduce the likelihood of streaking, and strengthen the fiber of the wallpaper. To do this, prepare a wide roller, brush, pallet and application material. It is better to use a latex primer. It will additionally provide moisture protection.

The primer is poured into the pallet. You need to be able to properly roll up the primer composition. Too much of it is not required so that there are no smudges on the wall. The roller is dipped into the solution and excess material is shaken off from it. The primer must dry. This usually takes up to 12 hours.

Tinting

It's time to give the coloring composition the desired shade. Similar actions must be carried out once, since in the future it will be almost impossible to recreate the exact shade. Pigments are available in various forms. Dry and pasty options are most common. The preparation of dry pigments consists in dilution with water, and the paste can be immediately added to the dye solution.

Tool selection and preparation

In advance, you need to prepare a tool that will be used in the process of applying paint. This work can be done in three ways: using a roller, brush and spray gun. The latter option is advantageous, but it is a professional tool that requires skill and experience to work with. But the result is better and better, and the wallpaper retains its integrity.

When choosing a mechanical method, you need to have both a roller and a brush on hand. The first tool will be used for the main work, and the brush will allow you to efficiently process hard-to-reach places. The roller must have natural bristles... It is permissible to choose a foam rubber tool only for processing wallpaper with a deep embossed texture.

It is necessary to apply the coloring composition to the surface with a thin layer. There should be no sagging, streaks and other imperfections on the wallpaper. A thick layer cannot be applied at one time, as this will not lead to a good result. With the alternate application of layers of the coloring composition, minor imperfections will not be visible and you can count on a high-quality result. Application of each next layer is possible only after the previous one has completely dried. This rule applies to all cases and it is strictly forbidden to violate it.

Painting should be done in opposite directions. The last roller movements should be directed from top to bottom. In this case, repainting is not required, since the coloring composition will lie evenly. This will help avoid streaks and create the right visual effect.

You need to shake off excess paint from the roller so that they do not turn into smudges. If the smudges still could not be avoided, then we will correct the current situation. In this case, you need to shade the paint with a dry roller. The surface must be processed carefully so that the surface does not need to be repainted in the future.

The work begins with the space near the ceiling and baseboards. The roller should be applied with equal efforts and the uniformity of the paint application should be monitored. When the entire surface is painted, you need to leave it to dry completely. Its time depends on the type of paint chosen. The manufacturer puts this information on the can with the coloring composition. Also, the duration of drying is influenced by environmental parameters. After fixing the first layer, you need to apply the second (in the same way).

Using stencils

There are different ways of applying paint and embodying interesting solutions in the interior. A stencil is a unique option that allows you to turn an ordinary room into a unique space with an exclusive design and unusual decoration. You can make a stencil with your own hands or buy a ready-made one. It can be created from different materials: thick cardboard, metal, plastic. Masking tape or spray glue can be used to adhere such elements to the surface. In this case, they easily peel off and do not leave marks on the surface.

Do not open windows during and after painting.... The temperature must be kept at the same level. Drafts and abrupt changes in microclimate parameters are also not allowed.

The smoother the temperature, the better the paint will dry.

Interior options

We have already talked more than once about how beautiful the design of the room turns out when using wallpaper for painting. It's time to make sure of this. The options we have selected for the use of painted canvases will finally dispel doubts and give rise to an irrepressible desire inside to use this particular version of the decor.

This photo is a good example of combining two colors in one room. One of the colors is bright, and the other is neutral, which is recognized as the correct contrast solution. They do not compete with each other, but complement and highlight the advantages that are inherent in each of them. In this case, the hallway smoothly passes into the living room, and the zoning idea is also well implemented.

A few years ago, residents of a large country were forced to be content with the wallpapers that were offered to them in hardware and hardware stores. But as time went on, production technologies changed, and modern paper was replaced by modern ones. People have the opportunity to paint the wallpaper in a color suitable for the design.

What can you paint?

Modern wallpaper production technology involves the use of high quality materials.

But first, it should be noted that ordinary paper wallpaper should not be painted.

No special relief is applied to plain wallpaper. Even if the paper wallpaper is painted, firstly, from the outside it will not look aesthetically pleasing, and secondly, the paper will swell and fall off after a short time.

There are three types of paintable wallpaper:

vinyl;
glass wallpaper;
non-woven.

Vinyl wallpaper is made of both paper and non-woven material. They can be dyed up to ten times. They are used in any premises, for kitchens and children's rooms it is best to select washable ones with a pattern.

Glass fiber is made from natural materials - dolomite, lime and quartz sand. Another component in the composition is soda. All these components are applied to a paper base. There are two types of fiberglass: single-layer and double-layer. They can withstand more than ten stains. Wear-resistant, so they can decorate the room for several years. They are washed with a regular brush and water. Most often, they are pasted over government and office premises.

Non-woven wallpaper is highly durable. They are based on non-woven material - a material that is made from compressed fibers. Foamed vinyl is applied over the top, resulting in various patterns. Coloring on a non-woven base lasts for more than one year.

It should be noted that on the market you can also find liquid wallpaper for painting. Liquid wallpaper is a relative novelty among building materials. It is more correct to refer them to decorative plaster. On sale, they are found in the form of dry mixtures and diluted concentrates. Liquid wallpaper in dry form must be diluted in water before application. They consist of safe substances - PVA glue, coloring pigment and a base - cellulose flakes. Depending on the colors, silk, dust and glitter can be added to the composition.

Among the advantages of liquid wallpaper is the fact that they hide the unevenness of the walls, cracks and chips. Mold does not form under them, microorganisms do not colonize them. They do not crack or peel off like wallpaper rolls. They do not have butt seams and provide good thermal insulation. Defective spots are replaced in a few minutes, no need to re-glue the whole room.

Advantages and disadvantages

As noted earlier, liquid wallpaper does not peel off after painting. The thing is that a diluted solution is applied to the wall, while the drawing can be made with your own hands. A layer of liquid wallpaper contributes to noise reduction, which means that extraneous noise from the entrance or street will not enter the room. The ease of the procedure for applying liquid wallpaper allows any adult to make repairs, this does not require special skills and knowledge.

Liquid wallpaper has its drawbacks - it can fade under the influence of sunlight, cotton absorbs odors, so you should not decorate the walls with this building material in the kitchen.

The advantages of vinyl, non-woven and fiberglass wallpapers were partially described in the previous section, and of the minuses, one can only note their high cost. Unfortunately, even cosmetic repairs cost a pretty penny.

When is the best time to paint?

After gluing the wallpaper, plasterers advise to wait about two days, during which time the wallpaper glue will dry completely, and the wallpaper will hold tight. If you apply paint on the same day after gluing the wallpaper, then there is a high probability of the appearance of marks and stains.

You should be careful when buying non-woven wallpaper, some of which are not intended for painting.

How to choose paint?

High-quality paints will also have to be matched to good wallpaper. It is not worth saving, since questionable products can negatively affect your health. If there are allergy sufferers or small children in the family, it is advisable that they were not in the room at the time of the renovation.

Today the most commonly used paints are:

alkyd;
acrylic;
water-dispersive.

Alkyd paints are bought for utility rooms - basements, storage rooms. These paints can harm human and animal health. The oils and resins that make up them can disable even a healthy adult man. But they have a number of advantages. They have a high saturation, are indifferent to humidity, do not deteriorate under the influence of ultraviolet radiation.

The antifungal components included in their composition do not allow the development of mold on the wallpaper.

Their service life is only five years, they are highly flammable, so it is undesirable to apply them near an open fire. The cost of acrylic paints is very low.

There are no harmful substances in the composition of water-dispersion paints, therefore they are suitable for city apartments as well. A huge selection of colors will allow you to match the color to any interior.

Latex paint on a water-dispersion acrylic base is mainly used for non-woven embossed wallpaper and glass fiber wallpaper. It dries up in a few hours and has no specific odors. Recommended for use in bedrooms, kitchens and living rooms, but cannot be used in bathrooms.

Water-based latex paint will last for years. Its elasticity is achieved through specially formulated substances. In the store, it is found in a universal white color, other colors are obtained by diluting it immediately before application.

Acrylic paints are suitable for city apartments, country houses and office premises. Such paints are bought even for kindergartens. There are no harmful chemicals in their composition, but the price, respectively, of acrylic paints is high.

Water-based acrylic paint for non-woven wallpaper. It stands out among competitors for its rich colors that do not fade over the years of operation. It can be applied both to paper wallpapers and glass wallpapers.

Acrylic paints are odorless, do not cover the wallpaper with a film, due to which they "breathe". And they dry in just one day.

Water-based paint does not contain harmful chemical components, therefore it is used in residential premises for commercial and domestic purposes. After painting, the wallpaper is moisture resistant, can be washed, and does not emit odor. Water-based paint can be used to paint kitchens, bathrooms and swimming pools thanks to the silicone base.

As for liquid wallpaper, their mixtures have certain dyes in advance. Some experts recommend painting the wall before applying liquid wallpaper. For this, oil paint is used. In this case, the spots do not appear, the saturation of the shades increases, and the surface is leveled. To make the textured wall stand out against the main background, there is a design solution: before applying liquid wallpaper, paint the walls in bright, exotic colors.

Remember that in cases where the walls in the room are already painted, for example, magnetic paint was used, before the next step - wallpapering, you need to "highlight" this place. Otherwise, unpleasant stains will appear under the wallpaper. To maintain the magnetization effect, the paint must be applied about five times, and the wallpaper must not be very thick. The next layer of paint is applied only after the previous one has dried. Therefore, liquid wallpaper is best suited for magnetic paint.

Now let's talk a little about the features of paints. If the paint has no gloss, it is matte. It is best applied in larger rooms. Semi-matte looks great in bedrooms, and glossy paint looks great in rooms where sunlight will play up the interior.

Semi-gloss paint is well cleaned, it is more advisable to apply it to kitchen walls, however, like satin paint, it is also moisture resistant.

Using a water-based varnish, you can increase the mechanical strength of the wallpaper and its water resistance. But it is worth considering the disadvantages of this event. Shine will "reveal" all the irregularities, the process itself is laborious, you need to be patient. Varnish contributes to a change in the main shade, but at the same time such wallpapers are well washed.

Consumption

Paint consumption will primarily depend on the types of wallpaper, and secondly on the varieties of the paint itself. Paper wallpaper, unlike glass wallpaper, absorbs more moisture, which means that much more paint will be required. On average, a liter of acrylic paint is enough for 5 square meters. m. But, if you apply the paint in several layers, this will lead to an increase in consumption.

Before you go to the construction market, you need to make measurements. Balcony blocks and doorways do not need to be considered. If furniture is installed in the room, for example, a wall or wardrobe, which is not planned to be rearranged, then the wall behind this furniture need not be painted - this will significantly save money.

Tools and materials

It is best to use a roller to apply paint to the wallpaper, this will save time on work and reduce paint consumption. There are several types of rollers, fur and foam rubber are suitable directly for painting. Velor and polyacrylic rollers are used for other tasks.

Masking tape is required to apply various stripes and patterns, thanks to it there will be no spikes, and the pattern will be even. By the way, you need to remove it very carefully so as not to tear it off along with the paint.

A roller is not suitable for painting small parts, so it is best to use a brush. Brushes, like rollers, must be wrung out thoroughly before application to avoid uneven layers.

The paint will have to be diluted in an unnecessary container - in an old plastic bucket or a large container of mayonnaise. After all, after the completion of all the work, this container will need to be thrown out, unfortunately, it is almost impossible to wash it.

A plastic bath is a specially designed device for painting walls. A small amount of paint is poured into the niche, and the upper part of the tray allows you to squeeze out the excess.

For some cases, varnish and color may be needed. It has already been written about varnish earlier, and with the help of a color scheme, you can create various color schemes. Kohler is most suitable for non-woven wallpaper. By adding a color scheme with the desired color to the white paint, you can modify the interior beyond recognition.

Using a stencil, you can apply special designs, patterns and inscriptions to the wallpaper. "Pictures" are obtained at a highly artistic level even by a person who does not have professional education in this area.

It is more advisable to use a spray gun for painting large rooms, this saves both consumption and the time spent on work.

With this tool it is easier to make the surface uniform.

Technology

First of all, it is advisable to prime the walls, and only then glue the wallpaper. Primed walls will allow the wallpaper to hold for a long time, and in addition, the primer will also level the walls. An acrylic or PVA-based primer is most suitable for residential premises.

When all the tools are prepared, and the wallpaper has already been pasted, the next stage of repair is ahead - painting them.

Preparing wallpaper for painting includes the following steps:

Removing dust from the surface. For this, a vacuum cleaner or a dry cotton rag, napkin is best suited.
Removing glue residues. Especially glue can manifest itself at the joints.

It is advisable to lay cellophane or plastic wrap on the floor. Old newspapers can absorb excess paint and stain your laminate or linoleum flooring.

All furniture, household appliances and electronics must be removed from the territory of the room. Keep paint away from batteries, ventilation grills and window sills. They are pasted over with masking tape and baseboards.

Correct painting of old and "freshly pasted" wallpaper on the wall with a roller with your own hands begins with the choice of a tool. Remember that the best paint effect will be obtained when using a roller with a long nap. Such a roller reaches even the most inaccessible places of the decorative layer.

The foam rollers can be used to remove excess paint from the "tops" of the layer. They are not suitable for painting directly, they will leave bubbles behind. A velor roller can be used for the same purposes.

It is more expedient to make a test one before the main painting. For this, less noticeable sections of the wall are selected. You can thus practice the application technique, strength and uniformity.

Water-dispersion paint is diluted with a small amount of water, while it becomes thinner. This paint is easiest to apply to wallpaper, and consumption is also reduced.

First, a brush goes through all the corners, joints between the walls and the ceiling or floor, and then, without rest, the remaining part is painted over with a roller. It is not necessary to squeeze the roller, the movements should be light and fast. The first layer must be completed before the paint is completely dry, otherwise the transitions and joints will be visible to the eye.

Two layers of paint should be applied to textured wallpaper. The second coat must be undiluted. The texture helps to hide the unevenness of the walls and poor-quality painting, so it should not be broken. No friction, just light paint on the wallpaper.

If you work together, then you need to start from the corners. Use a brush at the locations of sockets and switches. Remember that if you apply paint to an already painted part, a double layer will form, and later on, these are spots.

The roller needs to be periodically renewed: either take out the unused one, or remove excess nap from the old one. For this, soapy water is used, the result is fixed in clean water.

The roller is evenly wetted with chaotic movements along the mesh of the plastic tray, excess paint remains in the tray, and not on the wall. You need to roll it out until the roller is completely impregnated. If this is not done, unpainted parts will form on the wall. This procedure must be repeated constantly with a new addition of paint, after a while the process will be adjusted and there will be no problems with this.

Painters came up with a special technique for applying paint - W-shaped. A letter is drawn, and then it is painted over and so you need to continue from one corner to another. The main thing is to apply without streaks. But for simplicity, it is sufficient to apply paint with a roller from the ceiling to the floor.

If the humidity in the room is increased, then the drying process of the paint can be slowed down. Thanks to this, painting can be carried out in a longer time.

In many cases, tinting is required. By adding the desired tube with color scheme to the white paint, we achieve various color solutions. Do not neglect the instructions. If you overdo it, you can completely ruin the shade or complicate the repetition process for yourself.

By the way, the desired shades can be ordered in specialized stores. Thus, a can of new paint will always correspond to the previous one, since the dilution of paint with color is carried out according to special factory technologies, and not "by eye".

Non-woven wallpaper with a complex texture can be painted from the inside, allowing the rolls to be saturated with paint. The drawing itself will not be painted and will remain in its original color. In the future, it can be painted in any color with a brush. Conversely, you can paint directly the embossed pattern using an ordinary kitchen sponge. Light taps achieve this effect.

Painting of wallpaper glued to the ceiling is carried out using a stepladder and a roller with a large handle. By the way, you can use a spray gun for ceiling work. Ceiling glass wallpaper is the easiest to paint. All work begins from the corners, and then the remaining surface is painted with a roller. It is better to apply paint in two layers, in the first case - parallel to the window, in the second - across.

Although liquid wallpaper can be "freshened up" using a can of paint, the wall will become smooth after that. Its texture will be lost. It will no longer be possible to partially remove the material from the wall, only final dismantling is possible.

We paint in two colors

Not many people decide to paint a bedroom or living room in a combination. Some are accustomed to universal colors, others are afraid to ruin the interior with their own hands. And besides, no one will return money for mistakes made.

But at the same time, many design solutions provide for the combination of various colors in the room. This can be achieved either by pasting with different wallpapers, or by painting them in different color shades.

Remember that today special methods of combination have been developed.

You can combine:

colors similar in color;
making gradient transitions;
experimenting with different palettes.

To hide the transitions, special design solutions have been invented. One of them is molding. Moldings are made from safe polymers, they are easily attached not only to the ceiling, but also to the walls. It is more expedient to use wooden or plaster moldings in rooms where wood furniture predominates most of all - these can be bedrooms or offices. Polyurethane moldings are moisture resistant and should be installed in kitchens or bathrooms. All moldings are attached to the walls with special glue.

Curbs, planks and slats are popular in the design environment - they can be made from both natural and artificial materials. The choice is due only to the design of the premises and the financial situation of the customer.

But most often, masking tape is used for ordinary apartments. It is easily glued and easily dismantled after painting. Masking tape costs little money, is very durable, it can be used with a wide range of temperatures from heat to searing frost.

Let us dwell in more detail on the combined methods of painting wallpaper:

The most challenging is the method called "Accent wall"... With this method, not half of the wall is painted in one color, but the other in another. Here we are talking about painting three walls in one color, and the fourth in a different color. Or this method is used for the ornamental selection of ledges - fireplaces, chimneys and stoves.
Horizontal division most often found in city apartments, especially in cases where the lower part of the wall is stucco. The division can be both in the center and with a significant advantage. It is customary to decorate the transition with molding.

If the molding is not provided for by the design, then the transition should be performed using masking tape, but it should be removed within an hour after painting.

In children's rooms or in rooms intended for children, it is often done inserts from geometric shapes. First, the entire wall is painted with the selected color and the figures are marked with the help of masking tape. The second layer, which will differ in color, is applied after the first one has completely dried.

It was popular a few decades ago gradient coloring method walls. Today, the fashion for the gradient has returned. You can paint each wall a different color or go from dark to light. In the second case, the wall is first painted in one color, and then part of it is shaded.
Stripes, diamonds and polka dots are used less often, for their application you can use masking tape or a stencil.

How much can you repaint?

Unfortunately, it often happens that after wallpapering in the room, they need to be repainted in a different color. Let's say you didn't like the color or the interior has changed. Or maybe after a certain time, the previous color just starts to get boring. A reasonable question arises whether it is possible to repaint the wallpaper and how many times it can be repainted.

First, I would like to note that repainting is a popular trend today.

Gone are the days when redecoration meant the mandatory re-pasting of wallpaper. The furniture had to be taken out, the old wallpaper had to be torn off, the new ones had to be glued. It took a lot of time and effort.

Today, you can only repaint a certain section of the wall in the color you like, and that's it - the repair is over.

Manufacturers have taken care of their customers and produce textured wallpaper, the protrusion of which is sufficient to carry out painting work at least five times. Until the drawing is flush with the paint. Usually the quantity is indicated on the package, there are specimens intended for re-staining more than ten times.

But you won't be able to save money in this case.

Remember that the most common paper wallpapers swell and roll on the second painting.

It is also important what kind of glue they were attached to the wall. If cheap glue was used, then after the wallpaper “gains weight”, it will slide off the wall under its own weight.

It should be borne in mind that matte paints clog the picture, in contrast to glossy ones, which, on the contrary, emphasize it. It is advisable to use a water-based paint, it does not create crusts.

When repainting, you can experiment with the color scheme, for example, a combination of dark blue colors with white paint - you get a pastel color. And when you mix yellow and blue paint, a green tint comes out. If you mix yellow and red - orange.

Bright or color combinations are obtained by mixing green and red colors with white paint. You can experiment with your children, the main thing is not to forget what was mixed with what, in order to repeat this color in the future.

Interior design options

Any city apartment starts with a corridor. Even if guests come very rarely, the postman, the person checking the meter readings, or the social worker at least once a month will ring the doorbell. Therefore, comfort should be created in the hallway, and wallpaper plays a very important role in this.

From a design point of view in the corridor it is best to use paint in light colors, while the room will not look like a closet. Wall lamps and a glossy floor will complete the composition.

The second most important, and therefore no less important is in the apartment living room... Here guests and households spend most of their time. They rest, have tea and spend the night. Therefore, this room needs a combination of warm, soothing colors.If the living room is dominated by a predominantly white color - furniture, household appliances and electronics, then it is more advisable to paint the wallpaper in light shades.

In studio apartments experts advise to maintain a single design of the kitchen and living room. This combination visually expands the room.

Concerning kitchen, then in this room it is best to glue washable wallpaper. Even after heavy contamination with droplets of grease or smoke, it is very easy to return them to their original form. And the paint should be used one that does not absorb unnecessary odors.
Bedroom- this is a secluded room, people are in it mostly only at night. If a married couple likes to sleep before lunch, it is best to give preference to dark shades. And if - to get up at dawn - light. It is a well-known fact: dark colors without gloss absorb light.

Original children's room stands out from the background of the entire apartment. Such a room is not ashamed to show both relatives and strangers. Children in such a room will always find something to occupy themselves with in the daytime, and calmly fall asleep in the evening. Decorative painting in the apartment brings a certain charm. With its help, you can emphasize the design feature and hide defects and irregularities in the walls.
In the old days about sticking wallpaper In bathroom, one could not even dream of. The wallpaper itself did not hold up in this humid room, let alone paint it. They turned yellow, fell off after a short time, but, worst of all, a fungus could form under them. And it is very difficult to get it out.

In today's age of high technologies, manufacturers sell high-quality wallpapers and special paints for rooms with high humidity. You can paint the bathroom blue out of habit, or you can go for an experiment and paint in a combined way.

In a country house, especially on the upper floors, wallpaper can be glued, including on the ceiling. Such a transition visually raises the height of the room, hides uneven joints and plays up unsightly corners.
In office or municipal institutions using paintable wallpaper, you can significantly save on subsequent repairs.

The times when you had to re-glue the wallpaper every two years have sunk into oblivion. Today it is enough to glue the wallpaper for painting once, and you can change their color as many times as you like. At least five, at least ten. The main thing is just to remember that for this you need to buy high-quality building materials.

For information on how to paint the wallpaper correctly, see the next video.

It is possible to paint the wallpaper for painting without streaks with your own hands, subject to certain recommendations, and this will be the best solution for lovers of modern design. New possibilities are opening up for combining several color solutions, which in turn will have a beneficial effect on the interior. And if this task seems difficult to you, then a few tips on the nuances of working with this material will be very useful.

What is paintable wallpaper

Paintable wallpaper performs the same function as the classic wall design, except that there is no pattern on its surface. Manufacturers produce wallpaper for painting in either white or milky colors. This approach allows you to paint the wallpaper in any color at the request of the owner of the house. But the most important advantage of this version of wallpaper is that it can be painted repeatedly, and this plus will undoubtedly appeal to those who like to transform a room from time to time without spending a lot of time and without resorting to major repairs.

Types of wallpaper for painting

Important!The choice of paint and high-quality painting of wallpaper depends on the material from which it is made. And even if you immediately liked a certain surface texture, you should decide on the type of wallpaper.

Three basics for wallpaper:

paper;
non-woven fabric;
fiberglass.

Paper wallpapers "breathe" great, help to hide possible defects on the walls and have an affordable cost. Of the shortcomings, one can single out only that the number of stains is limited, and the surface cannot be washed in case of accidental pollution. Also, when sticking paper wallpaper on the wall, you should be careful not to damage the rather delicate base soaked in glue.

Non-woven wallpaper, in contrast to paper wallpaper, is much stronger and in the process of work does not cause trouble with care. The structure of the wallpaper is stronger and is designed for multiple repaints, as well as wet cleaning. One of the disadvantages of wallpaper on a non-woven basis is that the structure does not allow air to pass through, or in other words "does not breathe". The advice is suitable for those who live in wooden houses where air access is required to avoid the formation of dampness.

Fiberglass wallpaper, a strong and durable option for re-painting. Fiberglass wallpaper meets fire safety requirements and is easy to clean and wet. Well, environmental friendliness and ease of care complement the list of advantages with an undoubted advantage. Also, fiberglass is highly breathable, and if accidentally damaged, it can be repaired.

Choosing paint

Immediately, it is worth highlighting three characteristics of paints that should be taken into account, namely, harmlessness, since there will be people in the room, fast drying and good hiding power with a moderate content of solid components.

All these requirements are best met by water-based paints, which not only dry quickly, but are also completely harmless to those in the room.

It is also worth remembering about other properties of paints. For example, paints with latex additives increase adhesion and also enable wet cleaning.

Paints based on acrylic and silicone, ideal for rooms with increased steam generation or water. It can be either a kitchen or a bathroom and, of course, are ideal for rooms.

Paints based on rubber sealants will reliably protect even paper wallpapers from water. Also, after using this type of paint, the walls can be safely washed without fear of ruining the surface.

Step-by-step instructions for preparing wallpaper for painting

So, the walls are pasted over and now it's time to paint the surface. Make sure that the entire surface of the wallpaper is dry and that there are no traces of glue at the joints. For even painting, you will need short-nap paint rollers of various widths. Do not take rollers with foam rubber or long nap, as the foam rubber coating can leave "bubbles", and the long nap will not allow to paint over the texture of the wallpaper.

Although everything, of course, depends on the skill of the performer, we nevertheless recommend opting for a short-nap roller. Also, get a pair of brushes for painting in hard-to-reach areas such as corners or behind the battery. Compliance with the instructions will help to paint the wallpaper with high quality for painting without annoying stains.

Note!The texture of the wallpaper absorbs paint. To avoid uneven absorption, paintable wallpaper should be coated with a primer. To do this, use a classic primer, or paint applied in one layer.

After the primer is dry, proceed with the finishing paint. First of all, paint over the corners with a brush, and only then proceed to painting the entire surface of the walls. According to the instructions, the surface should be painted from top to bottom, gradually dropping to the floor. This will avoid sags or eliminate them in time. Do not hold the roller in one place for a long time, otherwise it can lead to drips and, as a result, to streaks in the future.

Do not allow the paint edge to dry out, as applying a fresh / wet layer will cause sagging and streaking. We finished one wall without interruption, only then move on to the next section.

Make sure that the amount of paint is evenly distributed on the roller, and if the paint has dried, then change the "fur coat" to a new one.

Advice!Well, if you want one of the main recommendations, then make sure that at the very beginning of the repair work, the walls are leveled with plaster. At the end of the work, say thank you, as a flat surface will eventually show up perfectly after staining.

Visual demonstration

Well, as practice has shown, it is better to see once than read 100 times. That is why the information on how to paint the wallpaper for painting, so that there are no streaks, shown in the short video, will be very useful to you. After viewing, you will definitely be able to do this stage of the repair yourself, without having over the skill or many years of practice.

Write in the comments: What difficulties did you encounter while painting the wallpaper?