Focusing the door leaf in height (shorting). Condition of interroom Door Can I cut the interroom door with glass

Each man before repair thinks:

• Where to start and on what can be saved?
• How to replace the doors if non-standard processes?
• What if there is no super professional equipment?
• How to be a private sector with its non-standard sizes?

Let's start with the same door block consists of two parts - the so-called "box" (lutki) and the door canvase. The box "tightly" is placed in the opening. From the inside the box opens the canvas, which can be glazed or solid (deaf). Boxes are with a threshold and without a threshold. This affects the overall size of the block. Doors differ in action (opening-closure) on "". Standard dimensions of door blocks assembled with the threshold depending on the thickness of the racks: 650 × 2050 mm (660 × 2060) for San.Unzlov: 750 × 2050 mm (760 × 2060) For the kitchen: 850 × 2050 mm (860 × 2050) for residential premises, etc. Many varieties of doors are known. Among the wooden doors, the framework design is most often found, and the board, plywood, fiberboard, glass is used as an internal cloth. Recently, laminated doors with laminated coatings are increasingly used, including imitating natural wood texture. So for saving funds, I would advise you to buy such doors. Such doors can be redone in almost any size.

You need to start with the measurements of the proof where the block will be installed. If at the moment the open is occupied by the old door block, then in order to remove the exact dimensions, it is necessary to remove the platband that is nailed along the edge. Then we measure the width of the brick to the brick (the outer size of the box should be less than the size of the outlet by 2-5 cm), measuring the height from the finished floor to the jumper-beam (the outer size of the box in height should be 1 cm at least less than the opening). But it happens, and in private houses it is often thick, that the finished opening is not suitable in size and it is simply impossible to expand it. In this case, it is necessary to make fitting the door of the door by reducing the size.

It is not so difficult, as it may seem at first glance. To do this, it is necessary to have a small arsenal of power tools:

1. Manual frezer.
2. Cylindrical milling.
3. Carpentry clamps.
4. Manual grinding machine.
5. Shurtholder.

trimming doors

Now everything is in order.

Due to this, you can adjust the standard sizes under smaller, not standard. What makes it possible to fill any loops.
I think that the door of the array (fully wooden) can also be triggered within the limits of reasonable.

Next, I will tell you how you can change the door block without removing the old box (Lutka) because There are cases that it is easy to disassembly, because it can collapse a whole discovery due to the specifics of the construction mainly - it concerns the old private houses, less often the old arrangement of apartments. Of course, it is possible to strengthen the arrogance of the goat, before dismantling, the profile, but this is additional work for you, costs and of course not safe.

We start with measurements.
We measure the inner size of the old box in width: let's say 1070 mm minus 30-40 mm for the accurate installation of the new box, if the old one is worth it. In the height of the inner size of the box from the top to the floor: let's say 2000 mm minus 20 mm. If there is a threshold, we cut it out and remove it. We do not need it. We get an outdoor size of a new one - 1980 × 1030 mm, which we will put.

The door block for this size of the Opel (1980 × 1030 mm) must be one-time, i.e. One door in width is greater, and the other is smaller. For example, 600 mm and 380 mm are the size of the width of the width, taking into account the thickness of two racks of the box and the gap between the doors - it is 4-6 mm, as well as 30-50 mm clearance for mounting foam. This size may vary depending on the thickness of the inserted box. And the height of the doors is 1930 mm.

How to reduce door canvases I have already written above.

As you can see the old box (Lutka) is not viewed. From the inside, the new standard (100 mm) box, as a rule, does not overlap the old one in width. Therefore, it is necessary to increase the width of the new box around the perimeter using a good expansion plank, which is sold in any door cabin. I usually use such.
Planck Dobly (MDF) Universal. Dimensions: Length: 2070 mm. Width: 120 mm. Toleshchina: 10 mm.

When the installation foam is dry after installation (preferably the next day) and painted painting, on both sides block
And cash is stuffed. After that in appearance guaranteed, no one will think that there were once old doors.

There are just as not standard sizes, for example, in width are small for two hollow or one-hour door, but for same-salted is Velic. In such cases, you can do door-book those. Folding door.

And yet, it happens that the standard one is 900 mm, it is not convenient to open in a narrow corridor.
It is not difficult.
✓ Take a door width of 900 mm, measuring 600 mm (if less, it will not be convenient to pass).
✓ The mode with a tree with a tree, but with such a calculation so that the canvas did not go to the departure, those. Slash one side of the door, turn over - the other mode is already on the departure.
In general, we do from one door, two doors.
Since the doors inside the hollow, it is necessary to insert the bars with dimensions with dimensions 27 × 27 mm in length on the length of PVA (27 × 40 mm, 27 × 45 mm).

But 27 mm for the doors with a thickness of 35 mm, the size remains unchanged. Otherwise, you do not insert a bar if it is 30 × 40 mm sizes. Then, when the adhesive is dry somewhere after 12 hours at air temperature +20 ° C, it is necessary to break the end a bit and paste the decor (edge) to the door of the door. We apply a hot iron to the edge to the door to the doors, cut and cleaned. When the canvases are ready, we connect them with each other with sheds. This we just divided one door in width - 900 mm by 600 mm and 297 mm.

And what if the door block with a converted door of 600 mm and 297 mm is not enough to fill the outline. Then it is necessary to simply select the standard door size and self-made half of the additionally purchased deaf or glazed cloth. With the latter will be a little more difficult because It will be necessary to make two cuts due to glass. Deaf is easier.

Measured how much it is necessary and cut off. In principle, everything is the same, what I told me earlier: cut off, the bar inserted, sled and glued the edge. The dimensions of the two doors can be very different: 600 mm and 400 mm; 700 mm and 400 mm to infinity.
Here is another example of the converted laminated door block. This block was made due to not matching the size of the standard.
Before the alterations, two door canvases were purchased, which were the same in width (600 mm).
Just one door I reduced 200 mm on both sides. 100 mm on each side.
Well, that's all on this topic.
Write in the comments and contact any question in the section "" - always answer.
Subscribe to news and learn more on the alteration of doors and not only.

Any homeowner, producing, expects that the new design will serve him, as they say, faith-truth, for many years. To do this, he chooses reliable and high-quality doors from proven producers or orders from professionals and wants to be sure that the repair of interior doors does not need. In most cases, it happens, however, there are situations when the door trimming is needed in height, for example, if during the next repair the owner wanted to replace the floor covering, and it decided that laying a laminate or parquet board would be an excellent option. As you know, laying the parquet board and laminate is associated with a change in the floor level, and, therefore, it is necessary to shorten the door so that it does not hide the floor covering when closing and opening. After all, it is unlikely that someone will come to mind and re-install interroom doors, entailing high costs of funds.

And here comes the most difficult moment. Few of non-professionals know how to properly cut the door to avoid possible damage and spoiled appearance of the design. Of course, ideally, you should contact the specialists who produce the installation and repair of interroom doors, and have professional knowledge and tools for doing this, not a simple operation. But if this option does not suit the homeowner or it is impossible for some reason, it can be interior door it can and independently. And for this, he will need either a manual or a manual milling mill in the arsenal of most homemade masters, as well as a video structure, exactly how to trim the door so as not to spoil it.

With the help of a manual circular saw, by the way, you can shorten the interroom door, without even removing it from the loops. To do this, first of all, it is necessary to thoroughly measure the necessary size of the heap, setting the circular saw disc in such a way that when passing along a flat surface of the floor and cut the door, making a smooth horizontal cutting across the entire width of the web. Visually to see exactly how to cut the door without removal, you can on the first video instruction in this section. This operation is carried out, as a rule, before laying a laminate to the floor, since otherwise it is much more difficult to cut the door without removing the loops.

In this video you will see how to trim the interroom door without removing it with loops

More complex, time consuming, but at the same time a more convenient way to shorten the interroom door is to use a manual milling mill. In the second video, you can see the whole process in detail. To do this, the door must be removed from the loops, secure on a flat surface of the table or workbench using clamps, pressing them from above the exactly exposed wooden bar, which will serve as a fuser guide. It is important to install it so that the cutter removes wood strictly at a distance that is necessary. The door with the cutter mill will take longer than with a circular, because there will be several passes, gradually deepening in the canvas. However, this way to shorten the door is more reliable, especially if the homemade master is not a specialist and

When repairs in individual buildings of the old building, where there are very low ceilings and not quite standard doorways, it often arises the question of changing the size of the acquired standard door. The same questions may occur during the device and repair of floors, as well as after laying a new floor carpet.

Most modern shops are now have the opportunity to change the size of the existing doors, as they take into account customer requests and organized small carpentry workshops directly in stores, or cooperate with firms that can provide this type of service.

But it does not always have the opportunity to find people who will take for changes in the standard door. And sometimes you need to fit the door already purchased and delivered home. And you are inappropriate to carry it for window. Therefore, the question of changing the size of the doors at home remains relevant.

And believe me, it may be possible to solve this question yourself, practical without any costs, except for their smelting and their own work.

How to trim the door

To change door standards, first of all, you need to know the structural features of your doors you have.

The design of interroom doors according to the manufacturer's method is divided into panel and frame (fillety, strapping).

Shield doors consist: from a frame - a frame made of wooden bars (RECES), the sheath produced from two sides, from a sheet material, and filling in the form of paper cells, polyurethane or spiral chips. Shield doors can be deaf and partially glazed.

Framework doors consist: from strapping (main bars), furniture (bars dividing the door leaf side) and aggregate (fililenies). A glass, fiber and chipboard are used as a panel.

If you take a window to the doors yourself, at home, will not be much difficulty, then change the width of the door is much more complicated, but it is also quite possible.

But let's stop still on the window. Before the start of work, it is necessary to remember the old Russian proverb: "Some seven times and one once again." It is necessary to carefully calculate everything, prepare the necessary tool, the necessary materials.

We will need:

1. hacksaw with small teeth
2. manual disc electronized or grinding angular machine (in commoner - "Bulgarian"),
3. plane,
4. car joinery and wooden bars of suitable size. We use bars - 30x30 mm.

If we use the "Bulgarian", then the cutting wheel in the metal is best suited for the production of work. When working, there will be a lot of smoke and Gary from him, but it will allow you to get drank without distinguishing and cracks according to such materials as Fiberboard and MDF.

If you produce a manual disk saw, we take a disk with small teeth and as much as possible - 80-12 pcs.

We will produce measurements for us and proceed to the process itself.

Place the cloth

And if, we make a disk saw cut, then on the opposite side, we attach the board to the door in order to get smooth, without a burp, dug.

If work, we will perform work with the help of "Bulgarian", then it is necessary to make a wooden structure on both sides of the door. Applying and securing the boards from both sides. This design will serve to stop the circle in it.

We produce window cuts

The lower part of the door leaf consists of a solid wooden bar, taking into account the possibility of window. But usually, its widths for trimming is not enough. Therefore, we will be useful, prepared by us a bar 30x30 mm. To close the cavity that has opened after the session. With the help of a hacksaw, we prepare the barrier you need along the length, catering in the thickness of the plane, and mounted on the glue.

Having cut the door leaf of the panel door or a panel door with glass inserts, it is necessary to remember the proportions of all its components (the ratio of the size of all parts and interchangeable). Having changed the size of the lower part of the door, we can break it harmony. And the door itself and the whole interior will be completely different.

Therefore, we need to consider the possibility of trimming the canvas on both sides and from the top, and from the bottom.

In the same way, as described above, it is possible to change the size of the door to the width.

But I would not recommend this, because the trimming, with the help of the tool existing in our presence, the length of 2 meters will produce very problematic and all the resulting flaws will be very much noticeable. It is better to do such a job on special machines and entrust her professionals.

And we can, if necessary, try to change the size of the doorway.

In general, we see that it is quite realistic to change the size of the door, if necessary, at home.

Getting Started, you will definitely succeed.

How to cut the door video

Replacing glasses

Feedback

How to properly cut the interroom door

Everyone, buying the door, hopes that it is not necessary to repair it for a very long time. For this, many people order doors from professionals to be confident in their quality. But there is nothing eternal in life, and repairs in the apartment is an inevitable action. After on the floor you install linoleum or laminate, the interroom door, by definition, will begin to close and open, since the height of the floor has increased. Therefore, you will need to trim the door, so that it opens freely, and did not creak. If you leave the solution to this problem for later, you can simply hurt the door. And do not forget that the purchase of a new model will be expensive, because anyone has no extra money.

Want to unlock the door from the bottom with your own forces, for this you need a circular saw. With the help of it you can shorten the doors, even without removing them from the loops. First of all, you need to make accurate measurements, so as not to cut off too much, then calm down, so that the hand does not get drown, and start acting. Remember that the gap between the floor and the door should be more than five millimeters. In this case, the door will look like "influx" and no other interference will see the native and acquaintances. Road shortening can also be performed using a manual milling. In this case, the door will have to be removed from the loops. Then it will be necessary to put on a flat surface and carefully fasten with the help of clamps, pressing the wooden bar, which must be smoothly set. It will serve as a trainer guide. It must be set it in such a way that the cutter removed the wood at such a distance, as planned - no more, no less.

As you already understood, you will have to suffer with the mill. And it will take this process more time than the first version of the door trimming. You will have to make a few approaches, while gradually deepening in the canvas. But do not forget that this method is more reliable and you will be easier to avoid irreparable errors. Experiment, try to achieve everything yourself, but do not forget that your actions should be carried out within reasonable.

http://www.dverey-remont.ru.

Everyone, buying the door, hopes that it is not necessary to repair it for a very long time. For this, many people order doors from professionals to be confident in their quality. But there is nothing eternal in life, and repairs in the apartment is an inevitable action. After on the floor you install linoleum or laminate, the interroom door, by definition, will begin to close and open, since the height of the floor has increased. Therefore, you will need to trim the door so that it opens freely, and did not creak. If you leave the solution to this problem for later, you can simply hurt the door. And do not forget that the purchase of a new model will be expensive, because anyone has no extra money.

Want to unlock the door from the bottom with your own forces, for this you need a circular saw. With the help of it you can shorten the doors, even without removing them from the loops. First of all, you need to make accurate measurements, so as not to cut off too much, then calm down, so that the hand does not flop, and start acting. Remember that the gap between the floor and the door should be more than five millimeters. In this case, the door will look like "influx" and no other interference will see the native and acquaintances. Road shortening can also be performed using a manual milling. In this case, the door will have to be removed from the loops. Then it will be necessary to put on a flat surface and carefully fasten with the help of clamps, pressing the wooden bar, which must be smoothly set. It will serve as a trainer guide. It must be set it in such a way that the cutter removed the wood at such a distance, as planned - no more, no less.

As you already understood, you will have to suffer with the mill. And it will take this process more time than the first version of the door trimming.

where / How does the door leaf cut neatly?

You will have to make a few approaches, while gradually deepening in the canvas. But do not forget that this method is more reliable and you will be easier to avoid irreparable errors. Experiment, try to achieve everything yourself, but do not forget that your actions should be carried out within reasonable.

Few of the masters know exactly how to properly shorten the door, as certain skills are needed for this, and, of course, experience. After all, damaging the door is a minute case, and fix it is a complex and tedious process. Of course, the most ideal option is to consult professionals that have the necessary knowledge and tools for this "operation". Today you can get confused in the diversity of firms that offer these services, and even more so understand which of them is the optimal and profitable option for you. But it is not worth a despair, you just need to know several rules:

1. It is not necessary to contact the company that recently declared itself, and in information it writes that there are already dozens of years on the market. In this case, the promotion of interroom doors can end the purchase of new ones.
2. If you decide to save, you should not order private companies, it is better to take advantage of state suggestions for repairs. So you will save a certain amount of money, and you will be rejected by the result.
3. In order to find an inexpensive company, first you need to compare prices for the services offered. After that, you can safely order the masters.
4. As soon as the master crossed the threshold of your home, check more about its price. If they are ordinal above, you can immediately call it to his company, and clarify the terms of the transaction.

How to cut the door to save veneer

... To introduce readers to the case, initially there was a question - how to increase the doorway by 3-4 cm in height ... than concrete sawing, etc. I suggested instead of sawing concrete to shorten the door itself in height ...)

Clear ... if new door, beautiful probably, veneered ... But the veneer can be cut off so that it is not noticeable ...

If this idea is interested in - I tell further ...

The following tools will be needed: a ruler, a square (the more - the better), a circular saw with a parallel focus, a construction knife, a wide screen, a pencil, a glue veneer for seeling a slice in the color of the door, iron, a good mood, 5-6 square meters. Meters Space and 2-3 hours of free time;)))

1. Tools workplace. It is desirable that these were two smooth tables, where you can put the door flat and reliably, so as not to hang out and swing. If there are clamps in the house - it would be nice to secure the door. If there are no tables, two stools can come up, the main thing is that it is convenient to work and does not bother around ... if something moves something in the process - there is a risk to spoil the door ...

2. Perform markup - Measure how much you need to cut off. Use the coal, carefully checking the "parallelism" and "perppercularity" ... make the markup on both sides. Check 2 times the correctness of the markup.

3. Take a sharp construction knife (it is also called "wallpaper), put forward it a little bit and start cutting the veneer to the main door of the door. The main thing is to cut through the "Gallow" in the veneer, which will go the circular actually propived. The groove must be in the width of the cut. You can try to bite the circular on some billet and measure the propyl.
Before cutting the groove and actually, the sawing can be pasted with a wide scope on both sides. Skop will hold the veneer from the rock ...
The groove cuts through the ruler for several passes, first with a light pressure, then increasingly increasing pressure on the knife. Slash the "groove" around the entire door, the main thing is that the groove "comes out", so it is important to make the right markup ...

4. Propil actually. The saw blade should be with carbide inserts with as many teeth as possible. If the circular is regulated by revs - put at maximum. Dropped out the depth. Put a little more door thickness. Install the parallel focus. Check the coal with the crossing of the installation of the disk relative to the circular bed. Turn the saw, wait until the disk drops maximum speed. Serve the circular very smoothly, without jerks ... especially at the "entrance" and on the "output" of wood. Ufff, the case is done;))))
Skinny schoch with propyl.

To unlock the door from below will help you master

Small jackets that remain from the circular are removed "skirt. Large chips (if any :() - PVA or any other suitable adhesive. But if you do everything neatly, the chips should not be.

5. The resulting cut can be closed with adhesive veneer in the color of the door of the door, the veneer is selected slightly greater widths and, heating it with an iron, sticks. When cool - you need to cut the residues with a knife.

6. All. Turn the door and go drinking beer.

I hope everything is clear ... good door.

Departure Masters in Moscow - without holidays.

Sometimes there is a need to trim the already installed door (installation of door sneaks), this happens when the installation of interior doors has already been implemented, and the owner needed laying of laminate to the floor, but the doors, unfortunately, are not calculated in height. In this case, a little cheaper and easier to shorten the door than to change it to a new one.

How to shorten the door?

The main task, execute everything competently and correctly.

High-quality cutting door bottom.

- Sometimes there is a question - how to shorten the door after an unforeseen previous laying of laminate or parquet.
- The network is full of descriptions, as dashing installers are controlled with this operation using a tracing circular saw.
- We recommend in no case to follow such advice.
- If you can allow such an operation to do the door from the MDF, then the veneer of the valuable wood will, most likely are spoiled.
- The complexity lies in the fact that even the smallest teeth of the saws will pull the veneer particles, forming chips and chances, it is no longer possible to correct such a marriage.

If you just need a cutting door from below, height, the price of veneer, MDF (mill, with tekla, ruled), then you are in our company. Our specialists will fulfill this work qualitatively and promptly, observing all the wishes of the owner. The owner of the apartment, performing the installation of interroom doors, hopes that the new door will serve him for many years. To do this, everyone is trying to choose high-quality and reliable doors only from proven producers or order from real professionals and assumes that it does not need to repair for a long time.

The trimming is carried out on the bottom using a planer or a mill. We have the most affordable prices for trimming a veneered door with glass on the height you need!

Basically, it happens, but sometimes there are such cases when the door trimming is needed, this happens when the owner decides that the laying of parquet or laminate will be an excellent option. Laying of any floor covering is associated with a change in floor level. And at this time comes the most difficult moment, since few of the professionals know how to properly cut the door to avoid serious damage and not spoil the appearance of the door.

Cutting door bottom, height, MDF.

- If you had to trim the doors after installing the loops, it means that you incorrectly determined the dimensions of the box relative to the canvas, or made a mistake with the loops.
- In the latter case it will correctly fix the error.
- Before installing the door on the loop, make sure that the dimensions are shorter than the lumen of the box for about 10 millimeters, and it is 4-5mm already, and the lines of the canvas and the fabric are parallel.
- At the same time, you can make sure that the vertical rack of the loop side of the loop is perfectly even - it is very important.

In order to avoid it is recommended to apply only to verified professionals who have rich work experience. You can find such specialists in our company by calling us or visiting our site and issuing an application. We provide all types of work. We provide a mandatory guarantee. Our masters in the process of work use only professional tools.

Company advantages:

1. All necessary works are performed at a time and as quickly as possible.
2. Ensure high quality services.
3. Warranty on all types of work.

To unlock the door from below will help you master

The current service centers that carry out the repair of interroom doors, as well as their maintenance, offer a lot of different services, among which is usually found and such a service as a trimming of the door in height, which causes sincere bewilders from many people. And indeed, whether the door trimming is needed in general, if it is much easier to perform measurements of the doorway and, in accordance with these sizes, purchase a finished design in the store or place an order for its manufacture in some workshop. The answer is simple - the need to shorten the door below often turns out to be the only way to save a family budget, because the implementation of such a procedure is much cheaper than buying a new door canvase. The reasons for trimming can be somewhat, but the main one is related to the performance of repair work, as a result of which the floor level rises. And this happens not so rarely.

Each person establishes new doors in his house, hopes for their longer life. It is quite logical that, for this purpose, high-quality and reliable door structures are purchased from respected producers or are ordered from professional masters. After all, such an approach gives confidence that the repair of such a purchase will be very soon. This is exactly what happens in the overwhelming majority. But people rarely take into account the condition of their outdoor coverage when choosing doors. And now it happens another repair, and the owner of the apartment is solved on a new parquet or laminate, as a result of which the floor level increases. After all, in order to organize a heap flooring system, to tempt a parquet board or mount a laminate, it is necessary to pave a layer of sound insulation and moisture protection. And if the base is not perfectly even, then also align it with a layer of a new screed. As a result, the perfectly mounted door leaf begins to touch the flooring. It is quite easy to solve this problem, you just need to cut the door from below, finishing it after that with a special protective composition, and it will again be freely open and closed. In this case, its functionality is absolutely not affected.

You need to shorten the interroom door by 5.5 cm

You can go and another way - to buy and re-install door structures, but this option is distinguished by a huge high cost, therefore I do not use in demand. The first option is significantly cheaper, although it is unlikely to bring it to life. After all, few people know no obstacle how to trim the interroom door to prevent possible damage and damage its appearance.

The services of professional masters performing the installation and repair of doors will come in handy. Qualified carpenters having solid experience with interroom structures typically use the following tools to reduce the height of the web: Circular saws and manual milling mills. The winner of the circular saw can shorten the interroom door, without resorting to its dismantling. Before carrying out such an operation, the carpenter thoroughly measures the alleged size of the sleeve, based on this data and the circular saw disc is installed. The quality of the flooring will depend on the wing of the flooring, since the tool passes along the floor surface. Next, the master performs horizontal propyl, cutting off the lower part of the web across the width. Such an operation should be made before laying a parquet board / laminate, as otherwise to shorten the door from the bottom without removing it from the loops is unlikely to succeed.

It is much more convenient to use a manual milling mill for these purposes, although this operation is more and more time. In this case, the door leaf is dismantled, after which it is mounted on a flat surface with clamps. The milling ager guide serves as a wooden bar, which is exhibited by the wizard at the required level. In this case, the mill must remove wood on a strictly prescribed distance. As you can see, even the presence of such a tool does not guarantee high-quality work, if it is engaged in a beginner. With a milling process, the process of trimming the door lasts more than with a circular saw, because the carpenter is forced to make not one pass, before the tool removes the desired part of the canvas. However, this option is more reliable: the edges of the cut are perfectly smooth, as a result of which the appearance of the door does not deteriorate at all. In other cases, the need for such repair works may arise in connection with the non-professional installation of door structures. Due to the allowed mounting errors, the interior door is shortly after installation, and only the attraction of an experienced specialist will allow you to protect against such problems.

Condition of interroom doors in height © all rights reserved

http: //xn--b1adcacoe0achkvffws.xn--p1ai

After the laminate is laminate, the floor rose by 2 cm. And one of the doors must be cut from below 1-1.5 cm.

The door is interroom, simple laminated Covered MDF. Inside corrugations.

What could be chopped the door so that:
1) was exactly
2) There were no chips, the effect of "brushes" on the spell.

Dropped out the scotch with painted.

Saw than? Drag on any format. (Saw for sawing sheet materials) There are in the complete large construction shopping center, on joinery production. Lobzik and hacksaw do not even try. In theory, you can make a cut-off sawing saw with a "frog", but you need very straight hands.

Is there anything experience? I just don't think that in the shopping center will be delighted if I bring them the door and say that it would be necessary to cut off 1-1.5 cm. In the shopping center did not saw, but saws a lot of doors on friendly production.

Pill EL.Lobzik pre-wrapped with solar scotch. It turns out not very beautiful, but if it is not crawled on the floor with a ruler, it is not noticeable. How much did they scream? What is there inside this height?

This is if it is cut along the line, and if the jigsik lead along the guide, then exactly there will be thin, will lead vertically. 16mm sawed as she tried, the line is direct, and the vertical walks. But the idea with the Milling Vaupsce all ideas is idea.

No, will not. On Fannery "Four" will be. On a 40 mm doorway - no. Discovative saw - most likely it will turn out. According to the guide bar.

Arsenal is most likely to cut off, while the price tag will be ridiculous. I have 32mm chipboard brought to cut. They took the calculation of 35r. For the item. Maybe they take the same door.

Typically, the canvas is not thicker 40 mm. It was said exactly that the man said, who put another door.

Yes, the cloth is 40 mm. It's just a door to cut a responsible business: -d and the battles are stupid, they closed with platbands and no shoals are visible.

If 5 cm bar, and you need to cut off 2 cm, then there are no problems - jigsaw and forward (scotch from "beard").
But if you are afraid, you need to cut off more than the width of the bar (you will touch the compartment with the corrugation), then it is better to take it to those who have special equipment!

Moreover, if you cut without a guide bar - vertically the cloth will walk less. Because there is a possibility to be slightly left to the right to press the jigsaw and control the canvas (not to deploy, namely, press horizontally)

With a bars, the cloth will lead a lot more concrete, right up to breakdown if you move.

Here you swelled the topic! Normally, these doors are sawing and hacksaw. I.Lobzik !!! :-D.