Turning on the gas boiler, first start: instructions. Entering the menu and service settings of the boiler Ariston Choosing a gas appliance for heating

Usually the first run gas boiler and work on setting up and adjusting it, we trust the masters from service centers. Why? Yes, because without their mark in the equipment passport, the manufacturer's warranty is simply not valid, and in the event of an early breakdown, we will simply be denied warranty repairs.

Whether this is actually the case is, of course, debatable. Specialists from service center will find a million reasons to refuse you free repair equipment. And even if you get such generosity from them, then your repair will last more than one week - then there are no spare parts, then the queue has not yet come, then it’s wrong. This is a proven fact and it is very difficult to disprove it. If you want a quick "warranty repair" - pay both for spare parts and for the work of the master.

By the way, in order to put the boiler on warranty service, you also need to pay money. So what is this guarantee? Pay for the warranty, then pay for parts and repairs. So where is the free warranty service? That is why, since you already have to pay for everything, I suggest that you independently start the gas boiler for the first time and set up the heating system. Moreover, it is not difficult.

Filling the heating system with water

We look under the bottom of the boiler - where all the pipelines are connected, and look for something like a small valve there. For each model of gas boiler, it may have different shape: one manufacturer makes it in the form of a valve familiar to us, the other - in the form of a rotating plastic pin. In general, from their form, the essence does not change - in extreme cases, open the instructions and look at its location.

We open this tap, not completely (so that air does not hang anywhere in the pipes, it is better to fill the system slowly) and fix our eyes on the pressure indicator - the pressure gauge. As a rule, most boilers of this type have an operating pressure of 1 to 3 atm - read the instructions for more details. We wait until the pressure gauge needle reaches 2.5 atm, close the valve.

Now the boiler will have to be left alone for a while - from each installed battery or convector must be vented.

For these purposes, each heater must be equipped with a Mayevsky crane. We open it and wait for the air to come down and the water to run. The water went - they closed the Mayevsky tap. This procedure must be done with each battery. Have you done?

Now we return to the boiler and again look at the pressure gauge - the pressure in the system should drop. We correct it, add water if necessary - the optimal pressure at which the boiler works normally is 1.5-2 atm. If you pump more, then during operation at a high temperature of the coolant, excess pressure will be released. This is due to the fact that when the liquid is heated, its pressure increases.

First start of the gas boiler

Having done all these simple preparations, you can proceed to the direct start of the boiler. Open the gas valve and plug the boiler into the socket. All sorts of symbols and numbers appear on the screen, but for a full launch, you still need to perform some actions.

First, press the power button and set the temperature control knobs to working position. After these actions, the boiler will begin to make futile attempts to turn on - this is normal and there is no need to be scared. The most important thing is that the circulation pump has started to work, inside which for some reason there is always air that prevents the boiler from fully turning on. It is his removal that needs to be done as soon as possible.

We remove the front cover of the boiler - in almost all cases it is fastened with two or four screws. We fold back the dashboard, behind which the circulation pump hides.

In the center of the pump there is a wide screw with a slot for a screwdriver. Here it is, dear, and you need to unscrew it a little, and when water runs out from under it without air bubbles, twist it again. Only now will the full circulation of the liquid in the heating system begin, and the boiler will start working.

At first, he will gurgle, make some strange sounds, but this is only for the better. Just be aware that all these sounds indicate that the remaining air in the system is being expelled into the expansion tank, where the automatic air valve releases it to the outside. Five minutes will pass and the system will return to normal - the pressure will stabilize, and the gurgling sounds will subside. And five minutes later, you'll be enjoying warmer batteries and unlimited hot water in the tap.

Here, in principle, is everything you need to know in order to carry out the first start-up of a gas boiler. The boiler is working, the batteries are getting warmer, and I think you will figure it out for yourself how to regulate the temperature of the batteries and hot water in the tap - read the instructions, everything is intelligibly described there regarding the control of your particular boiler model.

Was this article helpful to you? Subscribe to site updates to receive the latest articles on renovation and interior design before anyone else!

Maintenance and start-up of the gas boiler Ariston Uno

Preparing the wall-mounted gas boiler Ariston Uno for work

If the Ariston Uno 24 mi boiler is installed in an apartment, it must be checked that all regulations regarding air supply and ventilation of the room are observed (in accordance with current regulations).

Periodically check the water pressure with thermomanometer "L" and check (when the system is cold) that it is between 0.2 and 1.3 bar.

If the pressure is lower minimum value, you must restore it using the filling valve located at the bottom of the boiler.

When the pressure reaches 0.7 bar, close the valve. If the pressure drop occurs very frequently, there may be a water leak in the system. In this case, the leak must be repaired.

Switching on procedure - Press the "C" button. The electronic device will ensure that the burner is ignited without any manual intervention, depending on the heating or hot water command.

If after 10 seconds the burner does not ignite, safety devices boiler Ariston Uno 24 mi will block the gas outlet and the red light diode “G” will light up.

To turn on the boiler in this case, press the button "B". If blocking occurs again, check that the gas cock is open.

Heating regulation - It is possible to regulate the temperature of the water in the heating circuit using knob "A", setting the pointer between the minimum and maximum values. The temperature may vary between 45°C and 80°C.

Control using a chrono-thermostat - If a chrono-thermostat is installed, it is recommended to keep the heating temperature set at the maximum value using knob "A" for a higher efficiency of the Ariston Uno 24 mi boiler.

Technical and service maintenance wall-mounted gas boiler Ariston Uno 24 mi

Checking the tightness of the hydraulic system of the boiler, replacing the gaskets and restoring the tightness.

Leak test gas system boiler, replacement of gaskets and restoration of tightness.

Visual inspection of the general condition of the boiler.

Visual check of combustion and cleaning of the burner.

After checking, disassemble and clean the combustion chamber.

After checking, clean the injectors.

Visual inspection of the primary heat exchanger: checking the condition of the plates; cleaning the smoke channels of the heat exchanger;

Adjustment of the normal gas flow: consumption at ignition, at partial and full load.

Checking the functioning of security systems: overheating; on excess of working pressure;

Checking the functioning of the security system of the gas part of the Ariston Uno boiler: protection in the absence of a flame (flame sensor); safety of the gas valve;

Examination electrical connections.

Work control DHW circuit(testing performance and outlet temperature).

Determination of characteristics of combustion products.

General check of the functioning of the boiler.

Health check and right location smoke sensor. If necessary, replace with a smoke detector with similar characteristics.

Removing the casing

To approach the internal elements of the Ariston Uno 24 mi boiler, you must:

Unscrew the screws located at the bottom of the boiler;

Turn the mounting plates outward;

Pull the lower part of the front panel forward until the central latches come out and remove towards the top.

When removing the casing and turning the control panel, access to the internal elements of the boiler is opened.

Initial start-up of the boiler Ariston Uno 24 mi

When you turn on the device for the first time:

Make sure that: electrical connections and earthing are made correctly and a two-pole switch is installed with a minimum open contact gap of at least 3 mm; the plug of the automatic air vent of the heating system is loosened; pressure in the heating system
below 0.7 bar; gas cock closed

Unlock the circulation pump by unscrewing the plug on the front of the pump housing and turning the pump shaft with a screwdriver.

Connect the power supply to the boiler by pressing the button “C” and set the handle “A” between the minimum and maximum marks to activate the “winter” mode. Thus, the circulation pump will turn on; after 7 seconds, a lockout will be activated due to the absence of a flame.

Leave the Ariston Uno boiler in this state until the end of air bleeding.

To remove air pockets, loosen the plug of the deaerator of the circulation pump; re-bleed the air from the radiators; on the a short time open the hot water tap;

Check the pressure in the heating system, if it has dropped, open the filling valve and bring the pressure to 0.7 bar;

Check that the flue gas system is working properly.

Make sure the required shut-off valves open.

Open the gas cock and check the tightness of all connections, including the main burner (the gas meter must not record the gas flow). In any case, check the tightness of the connections with soapy water and repair gas leaks, if any.

Press the "B" button to unlock the ignition. The igniter will ignite the main burner; if this does not happen with first time, repeat the same operation.

Check the value of the minimum and maximum gas pressure on the main burner and adjust the pressures.

__________________________________________________________________________

__________________________________________________________________________

__________________________________________________________________________

_______________________________________________________________________________

__________________________________________________________________________

_______________________________________________________________________________

Gas boilers are manufactured different companies, which is accompanied by the supply to the market of equipment that requires an individual approach to installation and operation. But you don’t want to overpay for calling a specialist for installation work, do you? But how to connect the Ariston gas boiler on your own, taking into account the individual characteristics of the purchased equipment?

We will try to help you deal with this task - our publication describes the procedure for installing, connecting and configuring a gas boiler. The sequence of work during the first start-up of the equipment is also given. The presented material is supplemented visual photos and video.

Wall-mounted boilers are perhaps the most common among domestic gas equipment - they are most often potential buyers.

So, a modern gas wall-mounted boiler of the Ariston Net model allows you to: start, stop and control the temperature background of heating and hot water. Moreover, all these actions can be performed from anywhere at any time using a familiar smartphone or personal computer.

Here is such an intelligent gas equipment, using the Ariston Net household boiler as an example, that potential buyers of the 21st century prefer to install

The system provides constant monitoring of energy consumption, which is accompanied by significant gas savings. Thanks to a special software, the owner of the equipment receives real-time notifications of malfunctions.

In addition, if you activate remote control, it becomes possible to solve most problems remotely. However, let's first look at how to properly install a gas boiler household purpose brand Ariston, as well as the features of its connection, settings and procedure during the first start.

Stage # 1 - study the requirements of the manufacturer for installation

Judging by the requirements of the manufacturer of boilers Ariston, the installation of equipment is the prerogative of specialists only.

Hence the corresponding conclusion - self-installation and the first inclusion of the household gas boiler Ariston is theoretically impossible (more precisely, unacceptable). Moreover, the first commissioning of equipment is prohibited without a representative of the gas service.

The manufacturer also reminds the future user about the quality of the water with which the gas wall-mounted boiler will work. It is noted: if the water quality ( chemical composition) does not match technical requirements, the performance of gas equipment is not guaranteed by the manufacturer during the established warranty period.

The installation of gas equipment according to the “B” scheme requires the organization of effective ventilation and air intake in the working rooms.

Rooms where corrosive vapors may appear in the composition of the air are only allowed to use installation according to the “C” scheme (outside air intake). Such requirements provide corrosion protection for Ariston gas boilers.

Kits for connecting a chimney / air duct, as a rule, are not included in the list of Ariston gas boiler equipment. Accordingly, additional kits are ordered for a specific connection.

This is how the “pipe in pipe” system looks like, which is used as part of the design of Ariston gas boilers of some models

Many gas boilers brand Ariston are made taking into account the supply of air and exhaust gases through a coaxial system, the pipe diameters of which are 60 and 100 mm. Or a separate version can be used with pipes for diameters of 80 by 80 mm. The selection of the configuration of the exhaust gases and the air duct is accompanied by taking into account additional aerodynamic resistance.

Stage # 6 - connecting the equipment to the mains

To fully ensure safety, the manufacturer requires the involvement of a qualified specialist to connect and check all electrical connections of the Ariston gas boiler. The manufacturer voids the warranty on the equipment if a poor-quality power supply network is used and.

A ground loop for a gas boiler installed inside a private house is a mandatory event that is required not only for Ariston brand boilers, but also for any other similar equipment

The power supply system is calculated for the maximum power consumption parameter of the gas boiler. To connect the equipment, electrical conductors with a cross section of at least 0.75 mm 2 are used. correct safe work gas boiler provides reliable grounding.

The power supply parameters must be brought into line with the norms of the network 230V / 50 Hz, while observing the polarity and the presence of a grounding conductor. The ground conductor is required to be used longer in relation to the phase conductor and neutral. Wired connection - strictly permanent, without the use of sockets and plugs, made through.

First start-up and adjustment of the boiler

When with installation work and the connection is over, you can proceed to setting up and testing the equipment.

Performing the first run

The initial action that accompanies the first launch of an Ariston brand gas boiler is water. In doing so, it is necessary to set air valves radiators to the working (open) state.

The same steps to bleed air from the system apply to circulation pump boiler. As the circuit is filled with water, air is removed from the system, the water pressure on the pressure gauge reaches 1 - 1.5 atmospheres, the valve on the feed line is closed.

The first start-up of a gas boiler is usually accompanied by preparatory operations related to filling the system with water, venting air, checking the tightness of gas lines

At the next stage of commissioning of a gas boiler, actions related to the gas supply are performed.

The procedure is approximately the following:

• open the doors and windows of the working room;
• eliminate the presence of sources of open fire;
• check the burner circuit and control system for leaks.

Testing the control unit and the burner for tightness is carried out by briefly opening (no more than 10 minutes) the main shut-off valve of the gas line. Wherein solenoid valve and the manual damper of the boiler are set to the closed position. With this position of the system, the gas flow meter should show a zero result (no leakage).

Adjustment manipulations with the control panel

Modern gas heating equipment is equipped with a control panel where the user can set the desired operating parameters of the unit. Next, we will take a closer look at how to set up a household gas boiler of the Ariston brand.

Control during operation of the boiler, as well as control in the first start-up mode with the necessary settings, is carried out through the user control panel Ariston

Actually, the user's actions on the control panel are obvious here:

1. Switch on the device by activating the ON/OFF button.
2. Mark the operating mode parameters on the display.
3. Mark the service mode functions on the display.

Next, the gas parameters are checked, for which the front panel of the boiler is dismantled, the control panel plate is lowered and test manipulations are performed with the connection of the measuring pressure gauge to the pressure taps.

These operations are the prerogative of gas service specialists.. Do it yourself not recommended, as it is necessary to clearly know the functionality of the equipment.

Keyboard layout of the Ariston remote control: 1 - information screen; 2 – DHW temperature regulation; 3 – mode selection key (Mode); 4 - "Comfort" function; 5 – ON/OFF key; 6 - "Auto" mode; 7 - reset key "Reset"; 8 - regulation of the temperature of the heating circuit

The boiler is then started in test mode via the system function "Chimney sweep". To enter the test mode, activate the Reset button and hold it down for at least 5 seconds. The test mode is exited by re-activating the reset button.

Maximum/Minimum Power Testing

This type of test also provides for control sampling of pressure at specialized points of the equipment, followed by measurement of parameters on a pressure gauge. It is necessary to disconnect the compensating tube of the combustion chamber. Again, the "Chimney sweep" mode is used, activated through the control panel.

Similarly, the boiler is tested for the minimum power level. True, additionally used adjusting screw modulator, if it is necessary to correct the value of the minimum operating pressure of the boiler. On this occasion, a video is posted below, where for some reason the modulator is called a motor.

Putting equipment into operation

The process of starting the device provides for the following user actions:

1. Activate the ON/OFF button.
2. Select standby mode.
3. Hold down the Mode button for 3-10 seconds.
4. Wait for the bleed cycle (about 7 minutes).
5. Open the line gas cock.
6. Switch on the DHW operation mode with the "Mode" button.

If all actions were performed by a master of a specialized company, then he checks the compliance of the gas pressure during the operation of the unit and draws up an appropriate act.

Wall-mounted gas boilers from a series of modern equipment of the Ariston brand are a rather complicated technique, even if it is for domestic purposes. Hence the logical conclusion on the installation and launch of the Ariston gas boiler - the initial launch of the system should be entrusted to specialists. Costs are, of course, inevitable, but on the other hand, this is guaranteed right job gas system.

Did you install and configure the Ariston brand gas boiler on your own or did you entrust this work to specialists? Share your experience with other visitors of our site in the comments block - add a photo of your boiler, tell us about difficult moments, which you encountered in the process of self-installation of equipment.

Each owner of his house tries to make it as cozy and comfortable as possible. To achieve this, it is worth thinking about installing an Ariston double-circuit wall-mounted gas boiler, which will help solve problems with heating a dwelling. The device is very useful topics, which will provide heat both in an apartment and a private house up to 500 m².

Also, a gas wall-mounted boiler of a double-circuit type Ariston will allow you to quickly heat water for instant use. In this case, a person does not have to connect a boiler, which will require additional investments and a separate place for installation.

Descriptions of the double-circuit boiler Ariston

Today, there are many interesting models on the market for gas boilers. This is quite convenient, since everyone will be able to choose a device that is most suitable for the price, type, characteristics and installation method. Dual circuit wall boilers Aristons gained their popularity due to rare situations with their malfunction, as well as silence during operation, which is very important for maintaining a calm atmosphere in the house.

One of the most important components in all gas boilers is the burner, in this case it can be modulating or conventional. The first option is more popular than the second. When using it, the entire system will be regulated automatically, without human intervention. In this case, the power of the installed heating equipment depends on the temperature indicators.

The burner is also divided into 2 types:

• open;

The safest is, since it does not involve the ingress of combustion products into the room when emergency cases. Also in this case, the owner may not worry about building a chimney. It is necessary to bring a special coaxial pipe to the closed burner; it can always be brought out in any accessible place.

Boiler Ariston open type, in any case, requires a chimney to bring the products of combustion to the street. Also, do not forget about natural traction. Air will enter the system from the living quarters, so it will have to be constantly ventilated.

coaxial pipe used in closed system combustion, the good thing is that it is made of 2 layers. One is necessary for the withdrawal of combustion products, and the other will ensure the entry fresh air inside the boiler. Thus, the owner of the equipment does not have to constantly ventilate the room and worry about natural draft. The room will always have enough oxygen.

Distinctive abilities

According to reviews of gas wall-mounted double-circuit boilers Ariston, they have 4 distinctive features useful for their owners:

1. All models of this company are equipped with automatic protection systems.
2. The presence of a water pump, which is necessary for the constant circulation of water through the pipes.
3. Possibility to choose a model with expansion tank. With its help, automatic pressure control will occur inside the heating system.
4. Ariston equips its equipment various types ignition. It can be automatic, which will greatly facilitate the life of the owner of a particular boiler. Otherwise, each time the unit is started, a person will need to press a special button.

What are the advantages of Ariston gas boilers

Recently, the popularity of the Ariston brand has increased significantly due to high-quality gas boilers, and this is not in vain. operates silently and consumes as little fuel as possible. This will allow the owners of the unit to save on utility bills and, at the same time, provide comfort and warmth to the house.

The client will receive a high-quality device that provides round-the-clock water supply and heating of the house, even with a large area of ​​​​up to 500 square meters. Also, do not forget about the durability of the service of each boiler. The terms indicated in the guarantee are much more modest than they actually turn out to be. In terms of dimensions, the equipment is much more compact than other brands, which means that it can be installed absolutely anywhere, even in a small apartment with limited space.

Specifications

Almost all gas boilers from the Ariston brand have a capacity of 15 to 30 kW. Thus, each client will be able to choose the necessary indicators for the size of his apartment or house. It is also worth noting other distinctive characteristics of such gas equipment:

• at maximum efficiency, boilers have high level efficiency factor;
• all wall-mounted boilers have Russian instructions and designations on the equipment itself, so citizens do not have problems with controlling the unit;
• most models from this manufacturer are able to perfectly cope with water in the system and low pressure;
• special attention to this equipment should be given to those people in whose houses power surges often occur. Ariston boilers can easily cope with such jumps in the network;
• All models are very easy to operate. To start using the boiler, you do not need to study the instructions for a long time, all the features of operation are intuitive and accessible even for those who install such a unit for the first time.

In some cases, the boiler cannot simultaneously heat water and provide sufficient space heating, this applies to budget models. In this case, a person needs to think about installing an additional boiler.

Note! If we talk about expensive units, they have a special display that shows different characteristics, including the temperature inside the boiler and outside. This is very convenient in terms of introducing the necessary characteristics for the correct operation of the equipment.

Operating instructions for gas boilers Ariston

Before purchasing an Ariston gas boiler, you need to understand that if the buyer does not understand its installation, it is better to contact experienced specialists and entrust all the work to them. After all, even at the maximum detailed instructions not the fact that the case will end successfully. In this case, there is every chance of damaging the equipment, after which you will have to call repairmen, and this will result in additional costs.

It is very important to keep children away from the equipment. To do this, after, it is necessary to have a conversation with them and explain in an accessible language that nothing can be twisted and put on the unit, only an adult should do this. If the family leaves, for example, on vacation, after the boiler is turned off, it is also necessary to shut off all pipes for the supply of gas and water. Only after that the equipment is disconnected from the network.

If a display is provided on any model, all indicators that it displays must be strictly controlled. It can display malfunctions or deviations from normal operation that occurred during the heating process.

One of the most important points in the instructions for gas equipment is safety equipment. Before connecting the boiler, you need to familiarize yourself with it first.

What are the types of wall-mounted boilers Ariston

All Ariston boilers are divided into 3 series. They have different technical indicators and functions, namely:

1. Clas - this series refers to more bulky and powerful devices for heating residential premises. They are equipped exclusively with special regulators that automatically regulate the gas supply. This is necessary to save fuel, which is very convenient in terms of the cost of utilities and with frequent business trips of the owner of the house.
2. Genus. These are the most innovative and multifunctional models of Ariston gas units. They have more possibilities than other boilers from this manufacturer. Along with the equipment itself, the buyer will receive additional accessories such as a fan required for smooth speed control, as well as heat exchangers, primary and secondary. All devices from the Genus line are distinguished by the presence of a large liquid crystal display. It will display all the characteristics that correspond to the operation of the boiler at the moment.
3. Egis. The units from this series are small in size and attractive. appearance, which earned them great popularity among the owners small apartments. The device will fit well into any interior. Important feature of these boilers lies in the fact that, for their size, they have a fairly high level of efficiency and low fuel consumption, which is controlled by an intelligent control system.

Because of what the wall-mounted boiler may be faulty

The main reasons for the malfunction of Ariston gas boilers include the following:

• During the maintenance of the burner adjustment or control units, specialists made mistakes.
• Failed installation.
• Buying a fake, which is distinguished by low-quality components.
• Lack of sufficient air supply.

Conclusion

When buying one of the Ariston wall-mounted gas boilers from the seller, you need to check the availability of all necessary documentation, which

confirm that the equipment corresponds to the manufacturer. Only in this case, problems with the device will arise very soon.

Double-circuit gas appliances make our life more comfortable and enjoyable. They are quite practical to use, suitable for heating country houses and small apartments. They are used for heating industrial or warehouse buildings, the area of ​​​​which is not more than 500 sq.m.

The advantages of Ariston boilers are that, in addition to heating buildings in winter period, they heat the water used in the home all year round. It is quite convenient and does not require the installation of additional equipment.

General characteristics of Ariston boilers

The description of Ariston gas units must begin with the characteristics of their main part - the burner. This element is used to burn fuel and to transfer thermal energy to the heating system.

Types of boiler burners:

• ordinary
• modulation

The modulating burner is more convenient to use. It provides for automatic power control depending on the temperature of the device.

According to the type of removal of combustion products, burners are divided into:

• closed type
• open type

Units with a closed type burner are safer to operate. combustion products natural gas in this case do not fall into the room. Use is not required. A coaxial pipe is simply connected to the device and brought out.

Design coaxial pipe provides for the presence of two layers, which ensures the simultaneous removal of waste and the flow of air from the street into the burner.

Equipment with an open burner provides for the mandatory use of a chimney to remove combustion products.

Technical data of Ariston gas appliances

• Ariston boilers are used for heating and heating water, that is, they are double-circuit. Each modification has its own characteristics, but the common type of fuel is gas.
• The gas combustion chamber can be either open type or closed. In the presence of a chimney, units with an open chamber are used. And in apartments of multi-storey buildings, where there are not always chimneys, equipment with a closed combustion chamber is used.
• Power. Using this indicator, the gas consumption required to heat the room is calculated.
• Compactness. Wall appliances are used in small, narrow rooms. Floor-standing units used in industrial or warehouses are heavier and require more installation space.
• The presence of a control unit. This element is indispensable when turning off the water, a sharp decrease in gas. In case of any malfunctions, the unit will immediately turn off the device, which will prevent damage. It can also save fuel consumption.

Characteristics of Ariston boiler models

A distinctive feature of Ariston boilers is their high quality. After all, the name of the company is translated from Greek as “the best”.

Its products are especially popular among middle-income consumers. Gas boilers of this brand are purchased for space heating up to 500 sq.m. The company's products are universal. The transition to liquefied fuel is carried out only by replacing the burner.

Practical to use are dual-circuit wall-mounted gas appliances. It is represented by three lines, each with its own modifications.

For all modifications of boilers, the common is:

• small size.
• hot water supply, in the absence of its centralized supply.

Different modifications differ in structure, the common thing is their low cost and high-quality performance of parts.

Basic equipment of units from Ariston:

• double .
• electronic control module .
• carbon monoxide control.
• support of the microclimate in the building or in a separate apartment.
• control of water freezing inside the system.

Let's take a closer look existing species Ariston equipment.

Ariston Genus

• Are issued with the double heat exchanger. All modifications are double-circuit and are mounted on the wall.
• This model is considered the most functional of all Ariston devices. It has an LCD display, a control panel with buttons. Ariston Genus can be configured to work offline for a whole week.
• The display shows basic information about the status of the device and a list of possible errors. The burner is modulating, that is, fully controlled by electronics. This function increases the comfort of using this model of gas appliance, due to the minimum control by the consumer.

The Ariston Genus line includes Evo and more expensive Premium models.

The Evo model is a two-circuit gas appliance with a burner of both types: open and closed.

Genus Premium condensing boilers. They are used for heating residential buildings and commercial buildings. Power range from 24 kW to 35 kW.

Ariston Clas

• Small size device.
• This is a boiler with two circuits and a graceful appearance. The reduced dimensions did not impair its functionality in any way.
• Expansion tank for 8 liters. Hot water is heated fairly quickly

Existing modification:

• Evo is available in open and closed combustion chambers. Power with an open burner - 24 kW, with a closed - 24 - 28 kW.
• Premium Evo condensing type appliance. Has advanced comfort and freezing functions
• Premium simple condensing unit.

Ariston Egis

• Installed mainly in rooms up to 200 sq.m.
• The most common Ariston gas appliance model in our country. It heats water with a stainless steel heat exchanger, and a copper heat exchanger is used for heating.
• The compact device, differs in profitability and can be used under complicated weather conditions. For example, at sharp sub-zero temperatures.
• The device is equipped with a modulating gas burner , which allows for electronic control over the operation of the boiler.

This model is adapted to work in harsh climatic conditions. Normally withstands changes in gas pressure. The device is equipped with a collector into which condensate flows. This ensures operation at temperatures below 50 degrees.

The cost of boilers Ariston

The average cost of Ariston Genus boilers is 54,000 - 72,000 rubles, Ariston Clas - 25,000 - 34,000 rubles, Ariston Egis - 27,000 - 34,000 rubles

Choosing a gas appliance for heating

Ariston products can be found in the catalogs. There are many models of gas appliances. The main mistakes with the wrong choice of the unit are made from a lack of information. Therefore, before visiting the store, you should familiarize yourself with the basic tips for choosing a wall-mounted gas appliance.

When choosing a boiler, consider the following points:

• The size of the kitchen, as the place where the heating device is most often installed. In the store, the choice begins with consideration overall dimensions apparatus and select it individually for your kitchen.
• Then they go to the technical data and study the type of water heater in the device. If in a family a large number of person, it is not recommended to purchase a boiler with.
• In this case, it is more rational to purchase a boiler with a storage tank for hot water. and choose equipment for the amount of water that you will need for everyday use.
• Evaluate the combustion chamber of gas equipment. It is closed and open. It is recommended to choose a boiler with a closed chamber, because it is safer to operate. The presence of a chimney is optional, which is relevant in high-rise buildings. It is enough to buy and bring a coaxial pipe to the street.