Work with ceiling plinth. How to bend a ceiling plinth - quickly, simply and beautifully How to bend a plastic plinth for a floor

Sometimes the curved walls in the room or the presence of columns does not allow using an ordinary straight plinth, both for the floor and for the ceiling. And in this case, we have three ways to solve the problem: order semicircular wooden skirting boards, buy flexible ones made of plastic and bend ordinary, straight ones.

Next, we will tell you how to bend a plastic or wooden baseboard, and also touch on the topic of ready-made flexible moldings.

How to round the plinth with your own hands

You may not be able to make a baseboard for a round wall the first time. This is normal, because in any business that requires skill, you must first "get your hand in", practice. Therefore, if you are thinking about how to bend the baseboard with your own hands, then be prepared for damage to several moldings during the first trials.

We make a semicircular molding

The manufacturing method, which will be described below, is suitable for moldings made of polyurethane, PVC and duropolymer. From the tools you need to prepare a hacksaw and a building hair dryer - in some cities you can rent it. In principle, if the molding is thin, then an ordinary hair dryer with a power of 1500-2000W will also make it flexible.

To bend, on the back of the molding we need to make triangular cuts. We make the distance between them from 2.5 to 5 cm, depending on how much you need to bend the molding. We make cuts so that about 0.5 cm remains to the edge.

How to make a plinth in a semicircle: we make gashes with reverse side

• We heat up the molding so that the jumpers remaining in the cuts become flexible. We conduct heating carefully, from the back of the molding. We are closely monitoring that outer side not deformed from high temperature.
• When the baguette warms up well and becomes flexible, it must be carefully but quickly bent. Plastic cools down pretty quickly, so you should not hesitate at this stage.

Next, we hold the profile in a semicircular state until it cools down and ceases to be flexible. Now you can proceed to the installation of the molding on the floor or ceiling.

Bending plinth. This effect is achieved by heating the plastic

We make semicircular wooden baguettes

But here everything is more complicated. Cuts cannot be made, and the method that we propose to use will allow you to bend the profile quite a bit. However, if you only need to fit the skirting board to uneven wall, then this option is quite suitable.

First, we prepare spacers for a wooden profile. To do this, take the board, draw on it a semicircle of the future bend. Now, on both sides of the line, we fasten or nail the spacers themselves. As they can serve, for example, long nails. You can also come up with your own version. Spacers repeat the future semicircle of the profile, and are staggered, as in the diagram below.

Spacers needed to make the skirting board semicircular

Now we need to steam the baguette to make the skirting board for the ceiling or floor flexible and give it a semicircular shape. The easiest way is to boil a pot of water on the stove and hold the profile over it. How long it takes for the molding to become flexible depends on the type of wood. This moment can be determined by touch, when you try to bend the profile will begin to give in.

After the wood has steamed and become flexible, remove it from the steam and put it into the semicircle of the spacers that we prepared earlier. Here the profile should remain until the wood is completely dry. Ideally, we steam the planks in the evening and leave them bent in a semicircle until the morning. After drying, the bent profile can be installed in the place intended for it.

We make from wooden profile ceiling plinth, flexible

Buying ready-made moldings

On sale you can find ready-made flexible skirting boards for floor and ceiling. They are made from different materials:

• Plinth floor polyurethane, flexible.
• Soft molding and plinth tape made of PVC.
• Flexible plinth floor made of cork, semicircular, bent.

Flexible polyurethane skirting has optimal combination price - quality, used quite often. Skirting tape is relatively inexpensive, but it is capricious in installation and not every type of glue is suitable for it. It is often used in the bathroom. Flexible floor plinth made of cork is the most expensive of these three types, but the naturalness of the material and excellent appearance.

Flexible plinth, floor, cork

Radius bent plinth is made from natural wood. AT ready-made you can hardly buy such moldings, since they are made according to the radius of a certain bend of a wall or column. Therefore, this decor is purchased, as a rule, to order, and it cannot be attributed to cheap ones. However, bent semicircular moldings made of wood undoubtedly outperform plastic in appearance, so all time and financial costs will be justified.

Plinth radius corner, round, bent

Do you love the smoothness that rounded shapes give to the interior? Then you need to know how to bend ceiling plinth flawlessly, while not spending special efforts. Consider the main points and tricks, without which you cannot create a beautiful circle from ceiling fillets.

Radius Framing Ideas

So where are rounded ceiling borders used? Most often they are installed around columns, bay windows, decorative ceiling elements, interior structures of various modifications, for example, as in the photo below.

Also, often, a bending ceiling plinth is used as an interior element. With it, create interesting decorative objects on the ceiling.

If desired, you can decorate the wall with a ceiling border. Decorative interior frames will infuse the charm of long-forgotten ballrooms into any room. At the same time, it is not so difficult to make them yourself.

Inspired by ideas, you can safely proceed to the selection of ceiling moldings and their installation.

Which type is the most flexible?

Faced with the design of circles on the ceiling, and immediately a lot of questions arise: “How to bend, maybe special fillets are needed, or hire an expensive professional?”.

Let's start with the material. There are different not only in the method of manufacture, texture and color, but also in material. The last classifying point plays a decisive role when buying a baguette for radius decoration.

• Polystyrene have an interesting shiny surface. They accentuate stretch ceiling any design. But such fillets are very dense, rigid and inflexible. When you try to bend one of the ways they break.

• meet in modern interiors rare, and not found in store windows at all. They are ordered individually, and if you need to make a radius, then such elements are made in accordance with the required shapes and sizes.

• , and to be more precise - stucco, also not for sale in construction stores. Usually it is made by hand in silicone molds, which you can also make yourself. With the help of this plastic and quickly hardening mass, it is possible to create real masterpieces.

• are available with various embossing and in various tint solutions. In addition, they are flexible and easy to install. However, they are very easy to break. Most often they are installed in bathrooms.

• Polyurethane - have a mix positive qualities- flexibility, moisture resistance, beautiful noble surface, ease of installation and self-processing.

• - plugs for stretch ceilings. They are sold in rolls. Despite the exotic nature of the source material, they look beautiful and elegant. Such fillets are intended for stretch ceilings and can take any shape without much effort. Of the minuses, one can note their small width, which negatively affects high ceilings and a considerable cost.

It is precisely polyurethane skirting boards. With their help, you can create any form. And the low price in comparison with gypsum and wooden moldings attracts more than the prospect of making the interior unique.

Self clearance

Self-repair is an everyday thing and not so rare. Especially, finishing touches such as sticker ceiling baguette remains "for a snack" to the owners. How to bend the border with your own hands will tell the instructions below.

Technology

It is not so difficult to turn a bending baguette into a beautiful rounded interior element. So: how to bend a polystyrene foam product? You don't realize right away.

Consider the ways that will help in this delicate matter:

• Method 1. Incisions

A simpler rounded shape can be decorated with a baguette, curved in this way. This is done quite simply - small cuts are made on the back side, so that the molding can take a rounded shape.

• Method 2. Heat treatment

Another option for radius bending is heat treatment. She suits perfectly polyurethane moldings. When heated, they turn into a very plastic material, comparable in its flexibility to rubber. While the baguette is in this state, it can be easily glued to the right place.

• Method 3. "Designer"

Ceiling fillets can also be cut into small components, together repeating the shape of a circle. This is not easy to do, and only professionals can do it. An example of how it looks in fact, clearly demonstrates floor plinth in the photo below.

• Method 4. Modeling

And last but not least effective method creating a rounded shape - cutting off the stiffeners on the back side of it and pasting it with ordinary adhesive tape. Such fillets are able to repeat not just a rounded shape, but also any other, even the most complex modification.

If you have not yet decided how to bend the ceiling plinth, the video below will clearly demonstrate the available types of its processing.

Installation

Gluing a curved element does not require special adhesives or technologies. They can also be mounted on liquid nails, glue, mastic or special compositions intended for this.

Attention! In order for the baguette to have better adhesion to the wall, treat it with a primer throughout the entire process. The exception is when the molding is installed on the wallpaper.

If fixation of a curved plinth is required, then you can make it with masking tape, which firmly holds such a light decorative element and leaves no residue after removal. If during installation it came out adhesive composition, then it must be removed immediately, as it has the unpleasant property of leaving unsightly stains on the surface.

In principle, these are the basic rules that lift the veil on how to bend the molding. If you have never done such work, take an unnecessary piece of fillet and experiment - after all, luck smiles at the most persistent and courageous!

We bend the foam molding. Molding is an invoice convex plank with cross sections. Used for decoration various surfaces: walls, ceilings, doors, fireplaces, arches, giving them a more expressive, complete and neat look.

How to bend the plinth to a semicircle?

Curly moldings imitating stucco molding and woodcarving become a real highlight of the interior. Moldings make furnishings more expressive and neat, and the interior itself - noble and harmonious. Share the video with your friends. program, connect and earn. on the channel in ReDECORation contact ======================================¬== Like it? Leave a LIKE and comment so that I know your opinion and can make the video even better. And don't forget to SUBSCRIBE to the channel to be the first to see new releases:

social comments Cackle

Foam ceiling plinth: main characteristics and gluing technology

In this article, we will talk about how to properly cut, how to bend a foam ceiling plinth and how to install it. Until recently, there were no foam-based finishing materials that were light and comfortable to use. Therefore, most of the compatriots used paper panels to decorate the transitions of the walls to the ceiling, and only a few lucky ones could afford the use of gypsum stucco.

With the advent of baguettes made from extruded polystyrene foam, the situation has changed radically, as high-quality and aesthetically attractive ceiling design has become available to everyone.

Example decorative design wall and ceiling junction

Before you learn how to install foam ceiling plinths with your own hands, consider the main characteristics of this finishing material.

Main characteristics of extruded polystyrene baguette

In the photo, an assortment of foam baguettes

Expanded polystyrene ceiling plinths differ from similar products made from other materials in such qualities as:

• light weight and the ability to install on glue;
• simplicity machining and, consequently, the possibility of cutting sharp knife and other equally accessible tools;
• smooth white surface of the product, no need for additional staining;
• low price in comparison with polyurethane analogues of skirting boards and gypsum stucco;
• a wide range of standard sizes;
• a wide range of textures.

When purchasing polystyrene foam ceiling plinths, you can choose products with both perfectly flat and relief surface. Thus, one can choose decorative material, which will perfectly fit into both modern minimalist and classic interiors.

The abundance of standard sizes is another significant advantage characteristic of baguettes made of expanded polystyrene.

All these products can be divided into three categories:

• wide (thickness up to 20 cm) - great choice for classically decorated interiors and for rooms with high ceilings;
• medium (thickness up to 10 cm) - universal option, which can be used for its intended purpose in any premises;
• narrow (thickness less than 3 cm) the preferred choice for rooms with low ceilings.

The standard length of the foam ceiling plinth is 2 meters, which is very convenient when decorating rooms with not only a small, but also a large perimeter.

Important: In order to make the installation of baguettes easier and even a non-specialist could handle it, in addition to straight strips, corners for a polystyrene ceiling plinth are on sale.
The advantage in this case is that an inexperienced installer does not have to cut adjacent planks at an angle of 45 degrees, since everything is already ready.
As a result, the corner joint of the baguette will be accurate and reliable.

Now that we have learned the main characteristics and dimensions of the foam ceiling plinth, let's proceed to the implementation installation work.

What you need to pay attention to when installing foam baguettes

Filling gaps with glue

How to install foam polystyrene baguettes with your own hands so that the result looks attractive and at the same time is durable?

The quality of the finished result in this case depends on factors such as:

• degree of preparation of mounting surfaces;
• correct selection of glue;
• compliance with the installation instructions.

During the gluing of baguettes, you need to understand that accurate installation will not work on curved walls and on a crooked ceiling, as small gaps will be noticeable.

Of course, these defects can be repaired, for example, with the same adhesive that will be used during installation. But the overall impression of carelessly done work will still remain.

the only effective solution in this situation is preliminary preparation mounting surfaces. Gluing baguettes is the final stage in the repair.

How to bend a ceiling plinth

That is, the plinth should be installed when the walls and ceiling are perfectly even.

Important: If skirting boards are installed before wallpapering or before walls are painted, the mounting surfaces must be primed.
In this way, you will ensure optimal adhesion of the finishing material to the plastered surfaces and, as a result, it will be possible to reduce the amount of adhesive used without compromising the quality of the installation.

Tubes with glue and mounting "guns"

The next item is the choice of glue.

Currently, the following types of adhesives are especially popular:

• adhesive "Titanium universal frost-resistant" - has a toxic odor, excessive fluidity and long setting times;
• glue "Baguette" - an environmentally friendly composition based on acrylic resins, seizes for a long time, and therefore baguettes need to be held for a long time so that they do not slip.

What can be concluded from the above? None of the popular adhesives is perfect. Therefore, if the installation of skirting boards is carried out at the junction of plastered walls and a plastered ceiling, we use Liquid Nails glue.

What is the advantage of such a solution?

• "Liquid Nails" white color. which means they will not stand out on the surface of the foam;
• the glue sets quickly and after a minute of waiting, the bar will not slide down;
• glue is durable. and you can be sure that the installed baguettes will not move away from the walls and from the ceiling;
• glue can fill the gaps between baguettes and curved walls;
• glue is sold in convenient tubes. which are inserted into the mounting "gun";
• the price of a tube of glue, as well as the cost of a "gun" is low.

So, we learned what kind of glue to use so that the styrofoam ceiling plinth is easy to install and the result is durable. Now let's find out what the installation instructions are.

The technology of gluing baguettes from expanded polystyrene

An example of how to bend a skirting board with cuts

As already mentioned, in addition to straight foam strips, additional elements are on sale - corners that can facilitate installation work. Unfortunately, corners can not be purchased at every building materials store, and therefore we will consider what is the instruction for gluing ordinary straight skirting boards without auxiliary corners.

Corner Formation Example

From the tool we need:

• miter box;
• a special hacksaw with a small tooth;
• sharp clerical knife;
• measuring instruments;
• mounting "gun" with a tube of glue;
• clean cloth dampened with water.

Scheme for trimming planks at the right angle

• cut one plank from one end under inner corner, as shown in the diagram;

• we apply glue with a dotted line on the upper and side back of the plank;
• we apply the bar, starting from the corner of the room, press it and hold it for 1-2 minutes;

Removing excess adhesive

• with a wet rag or finger, wipe the excess glue that protrudes along the edge line;
• from the straight end of the glued bar we measure the distance to the next corner, if the whole bar fits, we glue it, if not, then we cut it off;
• plinth trimming is done in accordance with the previously proposed scheme, namely, the plinth is inserted into the miter box, the desired angle is selected and a neat cut is made.

Important: Styrofoam ceiling plinths get dirty quickly, so if you don’t want to subsequently paint them, so as not to leave stains, work with clean cloth gloves.

Conclusion

We learned what a polystyrene foam baseboard is and how it is installed. The details can be found by looking at this article, after which you can leave your comments about what you read.

More information

On the this moment we produce skirting boards in 4 colors (wenge, oak, maple, mahogany)

If you need a small amount of plinth - we can try to pick up from the remains of those colors that were made earlier or to order (oak, cherry, beech, mahogany, maple, pine, pear)

!!! When ordering from 50 pieces of plinth, a discount of 50 rubles per stick.

* Attention! Colors may appear differently on different monitors...

Price list for flexible plinth

NOTE - To obtain the color of wenge, we paint the baseboard with a special heat-resistant paint - execution 5 working days. The cost of painting one plinth plank in wenge color is 300 rubles.

We produce skirting boards in 3 design options:

* 50mm high. This plinthsavers and bottom are symmetrical. Overlap on the floor about 25mm
* 60mm high. Its shape is as close as possible to ordinary plastic skirting boards. Overlap on the floor about 17mm
* 70mm high. The most stylish of our line, more like a border. Overlap on the floor about 10mm.

Our floor plinth is easy to use. It is perfectly glued, sawn and planed. Such a plinth, like an ordinary wooden one, is fastened with nails or on, so it will not be difficult for you to lay it indoors. It does not ignite and is not affected by moisture. Therefore, our company offers you to make a choice in favor of plastic, which looks no less aesthetically pleasing than natural wood. You will also be pleased affordable prices on such a plinth.
When mounting on curved walls, the plinth should be heated to a temperature of +70 degrees Celsius and bent along the desired radius or curve. After cooling, it will become rigid, completely retaining the given shape. You can bend with the help of an industrial hair dryer.

Plastic plinth is used to give a finished look to the following floor coverings: laminate, linoleum and carpets. In room plastic plinth as organically as wooden, fits into the interior. The flexible pvc skirting we offer is produced in accordance with international standards and the standards for building materials. In addition, you will be pleasantly surprised by the affordable prices of our plastic flexible skirting board.

Flexible floor plinth for columns and more composite material

Many people during repairs often wonder "how to bend the printus"?
If you need a flexible skirting board, our composite wood-filled skirting board is the only solution. The cost of our plinth is much lower than its wooden analogues, but its consumer properties surpass them. If flexible wooden plinth to turn it into a bending, or rather, it is necessary to bend its plinth, then such a pleasure will cost you at least 3,000 rubles per meter and quite a long time for its manufacture and installation. By the way, the cost of installation by specialists will cost at least 2500-3000 rubles per one running meter e.g. wooden plinth for columns.

A revolutionary solution in the field of interior design is our bendable plintflex plinth costing from 140 to 180 rubles per linear meter. Ease of use makes it easy to stack. It is easy and simple to bend the plintflex plinth, with the help of a simple industrial non-professional hair dryer, with a power of 1000 watts or more (or a regular hair dryer), it is heated in the place where it is necessary to make a bend, softening to a state of free oscillation. Then it is applied to the surface of the envelope, allowing it to cool for 1.5 minutes. Having cooled down, the bending plinth remains in the form that was given to it. Then it is glued with liquid nails to the wall surface.

Flexible plinth can be tinted and painted after bending in any colors and shades with varnishes and paints for wooden surfaces.

Many are looking for a way to go around a column with a plinth, lay the plinth in an arc in the bay window, and the only solution is to use the plintflex bending plinth for this.

Whatever they say, these plastic skirting boards with cable channels that have become sore on the teeth look like a cheap solution for apartments that are not for themselves. All these plugs, corners, docking elements that fly off from a light touch of a vacuum cleaner fall off over time, and in general do not look at all aesthetically pleasing. They are a collection of dust and dirt. Needless to say, a cheap solution for a cheap interior!

We sell our bendable skirting board for a little more than a plastic hollow skirting board, but by installing it even on flat, straight surfaces, you will get an exceptionally stylish framing of the surfaces in your room. Durable, moisture resistant and which can be bent as you like - your imagination is now unlimited!

Plastmir invites you to opt for our plinth. Today is plastic pvc skirting board is an innovative product used in the field of decorative finishes premises. The plinth is made of a composite material that combines the best consumer qualities of plastic and the naturalness of wood. A high-quality soft plinth is not subject to the damaging effects of ultraviolet radiation, solvents and moisture, does not ignite and has a very small weight. All this is achieved through the use of special chemical composition- foamed polyvinyl chloride.

Our floor skirting board is made from a complex wood-filled plastic composite material.
Designed to frame any surface of any radius of curvature.
When joining, seams are sealed with material from sawing (shavings-powder) of the plinth itself - after grinding, the joint is absolutely not noticeable already from a distance of 1 meter. Wall mounting can be done with any traditional way, similar for fastening wooden skirting boards (nails, self-tapping screws). Places for drowning self-tapping screws can be masked with the same shavings from the plinth itself.

Radius plinth for floors, curved walls, columns, podiums, bay windows.

Radius plinth for floor and finishing intended repair. When carrying out repairs, people tend to choose a room design that will positively influence the energy, follow Fung Shui or use the latest fashion trends in decor. One of these types are columns, radius bay windows, rooms with rounded corners.

Often the issue with the skirting board for curved walls is postponed until later. As a result, by the end of the repair, in a hurry, customers seek to resolve the issue with the radius as quickly as possible. On an expensive parquet floor, a floor made of solid wood, a laminate floor, a non-profile baseboard is installed. Pieces are cut from a straight plinth and glued to a radius wall, a plastic plinth is used. Thus, crossing out all the beauty and attractiveness of high-quality flooring and, in general, the entire repair. Getting not the result that was in the project.

When buying floor coverings, a skirting board for straight walls is also purchased with them. But as practice shows, not all sellers of floor coverings have a curved plinth (radius) in their assortment. By purchasing a straight plinth, and leaving the issue with the radius for later, the client further adds to himself the problem of finding a radius plinth for the floor. Since for the manufacture of skirting boards for curved walls a straight profile (Euro profile) is used and it may not match the profile and size of the skirting board purchased earlier.

Turning to the "Plintusoff" company, you can always solve the issue with a straight floor plinth, but also choose the necessary plinth for round walls with individual parameters (color, size, veneer tone, veneer). Made just for your wall.

Pick up color solution for a curved skirting board it will not be difficult, with us you can always choose the color of the veneer from the warehouse program or order a color match according to the sample for your flooring, doors or wall.

The radius plinth for the floor is made from the following materials: and.

For the manufacture of a bent plinth, it is necessary to leave the measurer and make an electronic pattern. There are several ways to produce a curved plinth (radius plinth): by notches and type-setting (without notches).

Our own warehouse color program allows you to choose a skirting board for curved walls, for almost any manufacturer of flooring. If the color of the warehouse program does not match your needs, select the color, and if necessary, we will select the appropriate veneer. Choose from over 3,000 colors (shades) to really suit your needs. color scheme.

Turning to our company - you do right choice. Here you can choose the skirting board you need, order a measurement, manufacture a radius skirting board for the floor.

Buy a radius plinth and make no mistake.

Let's figure out what it is for and what kind of curved plinth to buy for installation on round walls, columns, bay windows, and so on.

If in country house, the apartment has bay windows, columns, walls with round corners - then you need to somehow close these corners. This can be done with the help of skirting boards specially designed for this.

Consider the products on the market for round (radius) sections.

The right choice of skirting board for round (radius) walls is a skirting board that is individually made to fit your walls. The material can be of several types - it is veneered, massive (using a stabilizing element) and MDF plinth.

What materials are curvilinear skirting boards made of, pros and cons:

Plinth radius veneered, made using the technology of arching with gash.

• Plus veneered skirting for curved walls - can be bent to a minimum radius of 200mm, you can choose the color and veneer for any manufacturer of flooring.
• The disadvantage of such a plinth is in the manufacturing technology, namely with the help of notches that are visible on the top of the plinth. The photo shows a sample of the radius with notches.

Radius from an array using a stabilizing element:

Made from solid wood with a stabilizing element - pine plywood.

• The undoubted advantage is the absence of notches on the top of the plinth. This kind of skirting board is very stable and flexible, thanks to the inclusion of pine plywood. How it looks can be seen in the photo.
• The disadvantage is the inability to bend to a radius of less than 300mm and not all types of veneer can be used for its production. The production technology consists of a set of veneer plates with a thickness of 1.5 mm.
  Veneered and massive (with the use of a stabilizing element) radius skirting boards always have the texture of natural wood, as they are made from valuable breeds veneer. Brushing technology can be applied if necessary.

MDF skirting board

Curvilinear (radius) plinth made of MDF - is used when it is necessary to select material without wood texture. Curved MDF skirting is an indispensable solution, as you can choose any color according to the RAL table - these are 3000 shades of color that will satisfy all your needs and allow you to choose the color to match the color of doors, walls and more
oh another.
For the individual production of a skirting board, measurement is necessary, since the radius is always an individuality, there can be no repetition.We recommend installing curvilinear skirting boards with the use of self-tapping screws with closing the place from the head of the screw with wax in the color of the skirting board or installation on glue according to the technology concealed installation. The photo shows several examples of installing screws and glue.

What other options for a radius skirting board for the floor can be.

Skirting without a stabilizing element - its main drawback is the lack of stability during operation. With changes in humidity, which is a natural process in the premises, deformation is possible over time, it can bend it. Need professional production and technology. This is often very rare.

Veneer + cork in the upper part. There are more disadvantages in such a plinth: it is limited in color. Top part cork will always stand out in color with your base skirting and flooring. It will be good luck if the color of the flooring matches the color of the baseboard. Secondly, it is universal for any walls, which may further affect its operational features (detachment from the wall, loss of the desired radius shape).

The next version of the plinth is to cut into segments the purchased straight plinth and
renew it. The advantages of this solution - a budget option, and matching in profile and color. But the disadvantages in this case are much more serious - this is the appearance. If you are solving the issue in a place that is not visible, then it is possible to apply this method. In a conspicuous place, we do not recommend using it. The photo shows an American walnut plinth cut into segments. The next photo shows the same area with the correct American walnut radius set.

The budget option is a plastic plinth, what are its advantages and disadvantages:

• low price.
• ease of installation.

On this, the advantages of this type of plinth end. The cons begin:

• aesthetic appearance immediately gives a cheap product.

If you purchased and installed natural floor coverings and a floor plinth, then by installing such a plinth, you deprive yourself of beauty and cross out all the charm of your floor. If the aesthetic appearance does not bother you, then an additional minus is the limited size, it will not always match your straight skirting board.
You can see an example of installing such a plinth in the photo.

Product categories Select category 2D Wall panels Bevelled MDF (0) 2D Beveled MDF Wall Panel (0) Beveled 2D Veneered Wall Panel (0) Beveled 2D Veneered Wall Panel (0) 3D MDF Wall Panel (1) 3D Veneered Wall Panel (3) Uncategorized (0 ) White Wood Skirting (55) White Skirting (96) White Shaped Skirting (45) White Laminated Skirting (7) Skirting MDF white(49) High MDF skirting board (64) Paintable MDF skirting board (49) Color matching skirting board (7) Radius MDF skirting board (8) Radius solid wood skirting board (8) Warehouse collection 100*15*2400 (28) Warehouse collection 100 *30*2400 (28) Warehouse collection 120*15*2400 (52) Warehouse collection 120*30*2400 (52) Warehouse collection 70*15*2400 (28) Warehouse collection 83*19*2400 (28)

Products

• 
  Veneered plinth 70*15 art. 0011 389.00 ₽
• 
  Veneered plinth 120*30 article 0024 705.00 ₽