Place non-woven wallpaper on the wall. How to properly glue non-woven wallpaper. How to hang fisile wallpaper with your own hands and create a decorative covering? Video

Non-woven wallpaper can be of two types: with a pattern and for painting. Such products can easily disguise wall imperfections that remain after repair work. Therefore, non-woven wallpaper is used in great demand. You don't need any special skills to glue them.

You should know that the non-woven base can slide along the wall, so it will be possible to paste it without outside help. If you choose wallpaper for painting, you can easily change the color scheme of the interior. In this case, the room will always seem fresh.

Today, large-width wallpaper is used quite rarely, but you can find it on sale a large number of of this material. Such wallpapers have some advantages:

Large-width wallpaper can significantly simplify the gluing process;
in this case there will be a minimum number of seams that spoil the appearance of the room.

Necessary preparatory work

In order for the gluing to be done efficiently, you will need to perform some preparatory work. First of all, it is necessary to calculate with maximum accuracy the number of rolls of material that will be needed to cover the room. To do this, you will need to measure the width and height of the room on each side separately. In the process of calculating the required number of rolls, you will need to add a few centimeters on each side to the length of the canvas as a reserve. For clarity, you can draw a diagram on paper.

When choosing non-woven wallpaper, you will need to pay attention to the batch number, which is indicated on the packaging. It should be the same on all rolls. If there is a drawing, it must also be identical.

In order for the wallpaper to fit correctly on the wall, you will need to prepare the room. The walls must be carefully leveled. This is especially important to do if you plan to paste wide wallpaper that will not lie correctly on the uneven walls. If the surface is not leveled, this will further affect the quality of the joints.

Sockets and switches will need to be removed. The wires will need to be insulated so that the adhesive mixture does not get inside the boxes. All walls will need to be thoroughly treated with a primer mixture and then dried.

To do this you will need to prepare the following items:

Video clip. Will be used for edge processing.
Polyethylene film.
Short bristled brush.
Plastic spatula.
Container for adhesive mixture.
Roller.
Roulette.
A simple pencil.
Level.
Non-woven wallpaper adhesive mixture.

Return to contents

DIY technology for gluing non-woven wallpaper

First of all, you will need to mark the walls. Non-woven wallpaper has an excellent edge and is glued end-to-end. The marking should start from the corner of the room. In these places, the canvas will be glued overlapping so that they can be processed correctly. If you plan to glue material 1.06 m wide, then you will need to set aside 1 m in all directions from the corner.

By using a plumb line or building level and a simple pencil You will need to mark a vertical line to the height of the builder. Using a tape measure, you will need to mark 1.06 m from the drawn line. Thus, you will need to outline all the walls.

If there is no pattern, you will need to use a tape measure to measure the height of the room in the place where the piece of wallpaper will be pasted, and you will need to add another 10 cm. The roll is folded onto the rolled out part so that the edges coincide. In this case, you will get an even fold. You will need to run your hand along the fold and then cut it with a construction knife. In this case, you can use a new stationery knife. In this way, wallpaper is prepared for the entire room.

The canvas will need to be rolled into loose rolls so that the front side is on the inside. Thanks to the non-woven base, there should be no problems in this case.

Next, you will need to dilute the adhesive mixture according to the instructions. It is allowed to use only adhesive solution for non-woven wallpaper. Water is poured into the prepared container, after which the glue is poured out in a thin stream. During the preparation of the mixture, it must be constantly stirred to prevent the formation of lumps that could prevent the wallpaper from being properly applied. The adhesive solution needs to sit for a while to swell. You can install a plastic mesh in the container to remove excess glue.

The roller will need to be immersed in a container with the solution, and then passed over the mesh. Next, you need to spread glue on the wall to stick one sheet. You need to start gluing the panel from the top.

You need to grab the extreme part of the canvas, and then attach it to the wall. The roll slowly goes down; in the process you need to smooth the wallpaper from the middle to the edges with a brush. In this case, you can also use a plastic spatula, but all actions must be performed carefully, as the wallpaper may be damaged.

Non-woven wallpaper should be glued so that it fits tightly to the wall. Bubbles and folds are not allowed.

After gluing the two canvases with a roller, you need to roll the seams of the material. The piece of wallpaper that remains below will need to be carefully cut off. This should be done after the wallpaper has dried. It is necessary to calculate everything so that the baseboard installed later can cover the lower part of the wallpaper. A border of the required thickness can be installed at the top of the wall.

Return to contents

How to glue non-woven wallpaper on corners

The first step is to prepare the corner of the room. This must be done while the walls are being putty. The corners are equipped with plastic fixtures that are attached to the walls with putty. The entire product must be completely dry, only then can you begin gluing non-woven wallpaper. In the process of gluing the corner, the wall and the plastic corner will need to be thoroughly coated with the adhesive mixture.

The panels will be placed overlapping; it is not recommended to glue the whole panel onto a corner. In most cases, the corners in the rooms are not ideal, and as a result, defects may occur: the corners of the material will wrinkle, the strip will become skewed. To eliminate this, you need to glue the corners correctly.

The canvas should be glued in such a way that there is a slight overlap on the wall located nearby.

The next strip is glued on the other wall, it is glued to the corner with a slight overlap. Next, this “tail” is cut off using a construction knife; you need to orient yourself along the vertical angle.

As a result, up to 2 cm of panel from the adjacent wall will be glued under this canvas, and the first canvas will rest against the edge of the corner.

Where to begin?

Before you start when pasting walls, it is worth studying non-woven wallpaper, its pros and cons and also features of working with such finishing. IN professionals are well versed in this, and If you If you want to entrust the work to knowledgeable people, you can contact company yaremont.ru — they renovate apartments without prepayment.

Trellis on non-woven fabric is a rolled material finishing material from cellulose fibers with polymer impregnation. On the market you can find both products made from pure non-woven fabric and wallpaper on a non-woven basis with a vinyl coating on the front layer.

Based on the structure of the front layer, smooth and textured trellises are distinguished. By color - colored and intended for painting (white). The instructions on the roll contain information about the material (width, texture, need to join the pattern), so you should study it carefully before purchasing.

Non-woven wallpaper has both pros and cons. Key benefits:

Density and strength.
Permeability to air and water vapor: walls can “breathe”.
Good moisture resistance, easy to care for.
Easy dismantling: vinyl peels off from non-woven base
One-time finishing treatment. The adhesive is applied only to the wall, and the roll itself does not need to be processed.

Minuses:

High price.
The need for regular cleaning of dust with a vacuum cleaner or damp sponge.
Vulnerability of the textured vinyl layer to mechanical damage.

If the listed shortcomings did not scare you, and you chose this material, it’s worth understanding in detail how to properly glue non-woven wallpaper.

Which glue to choose?

The result of the work directly depends on correct selection glue. Non-woven wallpaper is demanding on the quality of adhesives, so it’s not worth saving on purchases.

To work with this material, it is better to purchase special adhesive mixtures based on dry modified starches. The glue is prepared immediately before finishing. The soaked composition must be mixed thoroughly. The more uniform the glue is, the better.

Basic requirements for glue for non-woven wallpaper:

Good adhesion to both the base and the wallpaper itself.
Thick texture, making it easy to apply in an even, thin layer.
Lack of intrinsic color (does not turn yellow when dry).
No reaction with pigments (for those intended for painting).

You can find many specialized brands on the market today. But if you want to guarantee results, then you should purchase one of the proven options:

Metylan "Ultra Premium Interlining" - in addition to starch, contains polymer components. Adheses well to any surface, incl. drywall without putty and cork. Requires a more liquid dilution than indicated in the instructions, otherwise it will dry out quickly.
Quelyd “Special non-woven fabric” is notable for its antifungal and antibacterial additives that protect walls from the appearance of mold under the wallpaper. IN liquid state glides well, and this helps to join the canvases when fitting. Suitable for gluing dense trellises for painting.
KLEO Extra Non-woven - also contains antifungal additives. Can be used for both standard trellises and non-woven materials for painting. It is not advisable to use it for white wallpaper: sometimes the glue reacts with the surface and contrasting yellow spots appear on the finish.
PUFAS is a line of adhesives that includes compositions for working with non-woven materials. “EURO 3000 Non-woven special” is the easiest to work with and the leader in adhesion quality. If you are gluing wallpaper for the first time, then in order not to miss sections of the wall when applying it, you can take material with a color indication.

There are other worthy brands. But to guarantee results, it is better to use proven glue.

Preparing the walls

The next factor on which the quality of the finish depends is the preparation of the walls. Non-woven fabric adheres well to concrete, plaster, putty, drywall, wood boards (plywood, OSB) and other materials.

Optimal wall preparation algorithm:

Surfaces are cleaned of old finishes: wallpaper, decorative plaster, paints, etc. If old paint It holds tightly, it needs to be sanded with a medium-grained abrasive and removed from dust.
The plane of the surface is controlled by the rule. If there are differences of more than 10 mm per 2 m, bulges and depressions of more than 5 mm, leveling will have to be carried out. The walls are leveled with putty and sanded with sandpaper.
After leveling, primer is applied. Penetrating acrylic primer will not only strengthen the base, but also reduce its moisture capacity: water from the glue will leave more slowly, and non-woven wallpaper will hold more firmly. You need to prime in two steps, taking a break between approaches of 3-4 hours. Instead of a penetrating primer, you can use thinly diluted wallpaper glue.
Immediately before gluing, markings are applied to the walls. A starting vertical line is drawn at a distance of 1 meter from the corner (controlled by a level). Segments equal to the width of the roll are laid off from the starting line (standard - 1.06 m), and vertical lines are drawn to join the wallpaper.

Gluing non-woven wallpaper

The gluing process itself begins with cutting:

1.Cleanly washed or made up plastic film floor roll is laid front surface down. The required length is measured with a tape measure (room height + at least 10-15 mm margin). The roll is bent along its length and cut along the fold.

When cutting, the curvature of the room is also taken into account.

2. If it is necessary to join the pattern, then the next roll is cut with a margin. It is better to do the joining before cutting.

3. The adhesive mixture is prepared in advance (this will give the composition time to swell). If you are just mastering the technology of working with non-woven wallpaper, prepare the glue in batches. This way it will not have time to polymerize and reduce adhesion.

4. Ready glue mixture applied to the wall with a roller or brush. The width of the applied strip should be greater than the width of the roll - this will make it easier to fix the edge.

5. A strip of wallpaper, cut to size, is laid on the wall covered with glue and straightened from top to bottom, and its edge is aligned with the markings.

6. The surface of the wallpaper is smoothed to remove bubbles and wrinkles. Excess material from above and below is cut off sharp knife(a spatula is used as a guide).

7. The next canvas is glued according to a similar pattern. When gluing, the edges of the canvases and the drawings on them are joined. The joint must be made as tight as possible: after the glue dries, the non-woven fabric does not deform and cracks do not form.

8. The canvases in the corners are glued overlapping. After gluing, excess material is cut off with a sharp knife. To avoid the appearance of a gap, the two layers are pressed tightly with a spatula and cut through. After this, the edges are glued and pressed again.

Caring for non-woven wallpaper after gluing is completed is simple: just wipe the joints of the panels with a damp sponge to seal them and remove any excess glue that has emerged. The glue also needs to be removed from the ceiling - the sooner this is done, the less the risk that stains will remain.

While the adhesive composition has not dried, it is advisable to protect the room from drafts and temperature changes. These effects can lead to peeling of the wallpaper and the formation of bubbles. Walls covered with non-woven material can be painted only after the glue has completely dried.

We hope that the above instructions helped you understand the technology of gluing non-woven wallpaper. Now is the time to start practicing: follow the recommendations, don’t rush - and the result will be beyond praise!

Tools for gluing:

Roller with long pile;
5m tape measure;
Pencil;
Foam sponge;

Non-woven wallpaper consists of cellulose fibers and a polymer binder. Non-woven wallpaper is considered a universal coating, both in appearance and in quality it will appeal to the average buyer. True, he may immediately have questions about whether gluing non-woven wallpaper will be difficult, is it possible to do it yourself, is it easier to glue meter-long or standard wallpaper? And how to prepare the surface of the walls for gluing?

How to glue non-woven wallpaper: important points

The big plus is that non-woven wall lining does not require special care. If it is to be painted, then dispersion and acrylic dyes will look great on it. Most of this wallpaper is not afraid of moisture, so you can wash it using a soap solution.

As for preparing the walls before work, it is very important that the entire surface is of a uniform color and, if possible, that its color does not contrast with the color of the wallpaper.

If you glue non-woven wallpaper correctly, it will look like a continuous covering and the seams will be invisible

Some important points in gluing non-woven wallpaper:

Good non-woven wallpaper has a high-quality edge, which allows you to glue this wallpaper end-to-end. And the adjacent canvases will outwardly look like a continuous coating, and the seam, one might say, will not be visible.
Wallpaper is prepared only after checking it for defects. Always adhere to this rule: first inspect the entire unfolded roll, and only then cut.

After this, start preparing the tools for gluing.

Non-woven wallpaper: how to choose (video)

Tools for gluing non-woven wallpaper

Everyone who glues wallpaper themselves, with their own hands, has their own list the right tools. But if you are doing this for the first time, or are unhappy with past experience, you can use the following universal list.

Tools for gluing:

Construction level (if there is a laser level - ideal);
Roller with long pile;
5m tape measure;
Plastic spatula for rolling wallpaper;
A sharp knife for cutting wallpaper;
Narrow spatula (metal);
Pencil;
Foam sponge;
A bucket for glue and a bucket for water.

Basic tools for comfortable gluing of non-woven wallpaper

Perhaps some additional tools may be needed to prepare the walls. Wide wallpaper glued using the same tools.

Related article: Which chainsaw to choose?

How to properly hang non-woven wallpaper

Non-woven wallpaper is remarkable because it can be glued to virtually any surface - plaster, wood, drywall, chipboard, paper, concrete. Be sure to clean the surface of the walls from the previous coating; if the wall is painted, the paint must also be removed. If you find good reasons not to remove the paint, at least sand the painted wall so that the wallpaper adheres more easily to the surface.

Is it possible to glue non-woven wallpaper onto old wallpaper?

Theoretically, this is possible, but there are some nuances.

How to properly glue non-woven wallpaper onto previous wallpaper:

The previous coating should be paper and thin;
Old wallpaper should adhere firmly to the surface of the walls;
Old wallpaper cannot be much darker than new wallpaper.

It is worth warning that the risks of defects in this case are high. For example, bubbles may appear under the wallpaper, or the wallpaper may begin to peel. It is believed that the service life of the new coating from such gluing is reduced.

Is it necessary to apply glue to non-woven wallpaper?

It happens that during repairs a person is overcome by doubts, and he still smears both the strip and the wall. If, as it happens, you have already smeared the strip, then you do not need to apply glue to the wall. Just wipe it with a cloth at the joints.

There is no need to apply glue directly to the wallpaper; this is written on both the label and the wallpaper glue. Glue is applied only to the wall

But it’s easier to apply it to the wall, and then glue the prepared strip. Many people mistakenly smear the entire surface of the walls, but only the immediate work area is needed. If the wallpaper is meter high, this zone increases.

Is it possible to glue non-woven wallpaper onto non-woven wallpaper?

It is highly not recommended to glue non-woven wallpaper on top of other non-woven wallpaper. The risk of the wallpaper falling off is great

Use a needle roller to go over the surface as much as possible. more holes formed on the old wallpaper, then the adhesion to the new ones will work better.

Do I need to prime the walls before gluing non-woven wallpaper?

Of course, you should always prime, no matter what kind of wallpaper you glue. And non-woven wallpaper definitely needs to be glued to a primed wall.

A primer is not needed only in the following cases:

If the repair is temporary, and the wallpaper is, in principle, not intended to last long;
Wallpaper is light and paper.

If the surface on which the wallpaper will be glued has a defect, then it must be primed

Why do you need wall primer? It's simple - it increases the adhesion (that is, cohesion) of materials, they will stick better to the base.

Is it possible to glue non-woven wallpaper onto a concrete wall?

Of course, there is no need to glue it directly to concrete. First, level the surface with your own hands, apply putty and primer.

How to prime a concrete wall:

Take liquid glue solution. Apply glue evenly in the first layer, and in the second layer the adhesive solution should be thicker.
Double coating will increase adhesion, which guarantees successful wallpapering.

If you have ever had to glue wallpaper with your own hands, it is quite possible that you cursed everything in the world: heavy panels, too thick or very liquid glue, and uneven corners in the room, and themselves for gluing the canvas upside down. And if now you are again thinking about making repairs with your own hands, read about how to hang non-woven wallpaper, since the prices for the services of wallpaper craftsmen are comparable to the price of the material itself.

At correct gluing non-woven wallpaper will retain its attractive appearance longer

Features of non-woven wallpaper

Despite the fact that non-woven wallpaper differs little in appearance from other types of wallpaper, it's not quite regular material. Decorative layer the vinyl in them is not sprayed directly onto the paper, but onto a non-woven lining, which is glued to paper based. Non-woven fabric – non-woven material, obtained by pressing fibers. It has an amorphous structure, so it remains highly stable in all directions. This greatly simplifies working with the material. The weight of the canvases is also reduced, so non-woven wallpaper, as a rule, has a width that is twice the width of ordinary canvases - 1 m 6 cm.

Wallpaper with a non-woven base is often unpainted, which gives additional features for the flight of design ideas and creation unique interior. If you want to not only hang non-woven wallpaper yourself, but also decorate it with paint, it is better to consult with experienced craftsmen. After all, not every paint is suitable for such wallpaper. In addition, there is a multi-layer decorative coating and painting individual elements manually.

Designers offer very unusual options for non-woven wallpaper to suit every taste.

Surface preparation for gluing non-woven wallpaper is the same as for other types. The walls must be clean, puttied, and primed. Only minor scratches on the surface are allowed. But there is one trick: so that when painting non-woven wallpaper you do not have to apply paint in several layers, it is better last layer Apply primers with a tinted compound. But, unfortunately, tinted primer, and even the right color, is sometimes difficult to find in our building materials stores. So prepare it yourself. Just dilute a little paint in the primer, which you will use to paint the walls after pasting. The tinted primer is applied with a roller after the last sanding.

How to properly hang non-woven wallpaper: preparation for work

You will need a standard set of tools - the same ones that are needed to work with any type of wallpaper. This is a pencil, a tape measure, a wallpaper knife with a spare blade for it, a water or laser level, a wallpaper ruler, a stepladder, rubber rollers for the fabric and joints, a sponge and dry cloths (gauze is also suitable), two containers for glue.

Wallpaper is glued to dry and clean, pre-prepared walls.

Work begins from the window, gradually moving deeper into the room. The edge of the first strip must be marked with a level. But no need to draw a solid line with a pencil! The fact is that non-woven wallpaper is very sensitive to dirt, and this line will show through, even through several layers of paint. The marking should be done only with a very thin dotted line.

Dissolve the glue according to the instructions on the package. Use a special composition for non-woven wallpaper. It differs from other types of glue in its oiliness and ductility, so it does not absorb into the base for a long time. The glue should be applied to the wall, not to the wallpaper. Many people, without asking how to properly glue non-woven wallpaper, do it the traditional way: they spread the wallpaper with adhesive. In this case, after the wallpaper dries, the glue is pulled together between the canvases, so gaps from 2 to 5 mm wide are formed. Remember: when gluing walls with non-woven wallpaper, glue is applied only to the surface of the wall!

The adhesive composition is applied to the walls, not to the wallpaper

The adhesive composition is applied to the walls in the usual way using a roller and a brush (in the corners). This makes it happen neatly and quickly. To avoid getting glue on the surface of a previously pasted strip, apply it wider than the strip, about 10 cm.

Subtleties of gluing and painting non-woven wallpaper

Do not cut rolls into strips. Even if they have a pattern on them, you can adjust the wallpaper to the location. But most often, non-woven wallpaper does not require adjustment. Therefore, you can unpack the roll and glue the canvas to the wall immediately after applying the glue, having previously determined where the top is and where the bottom is. Make an overlap of at least 5-7 cm onto the ceiling, and cut the wallpaper from below exactly along the baseboard. The overlap from above is needed to compensate for the slope of the ceiling. You can reduce the margin to 2 cm if you know that your ceilings are more or less even. Immediately after gluing the strip, cut the stock using a sharp knife using a wallpaper ruler. Surplus adhesive composition are removed with a damp and clean sponge, and the next strip is glued end to end.

Non-woven wallpaper can be painted, obtaining original and unusual visual effects

You can glue the canvas not perpendicularly, but parallel to the floor. This will allow you to avoid vertical seams, which a person usually looks for when entering a room covered with wallpaper. Pasting wallpaper horizontally creates the illusion perfect walls.

Non-woven wallpaper should be painted no earlier than two days after gluing. There are many ways to create additional effects that emphasize the texture of the wallpaper and highlight some of its elements. But it is important to understand that there are special paints for non-woven wallpaper, and they are not cheap. Create stylish interior using cheap paint not intended for non-woven wallpaper is simply impossible.

Can be combined different kinds wallpaper and decorate them multi-colored paints. Or you can use one paint, but apply it different ways. Below are unusual ways staining.

Creating a decorative coating

Except traditional technology There are several options for painting wallpaper (using a roller and brush in the corners) non-standard ways.

When painting non-woven wallpaper to obtain best result It's better to use a foam roller

Firstly, the wallpaper can be painted with latex paint on the reverse side before gluing the canvas to the wall. The non-woven base will change its color, and the relief of the foam vinyl will stand out beautifully against this background.

Secondly, as mentioned above, you can apply paint to the walls and, after waiting for it to dry, glue the wallpaper. In this case, the color will slightly shine through the base.

Thirdly, the raised part of the pasted wallpaper can be finished with a hard, lint-free rubber roller. Move along the canvas with almost no pressure so that the indentations are not filled with paint.

Fourthly, you can carry out the initial painting in the traditional way (with a soft roller), and use paint of a different color to finish the relief.

Video master class: how to glue non-woven wallpaper

You should know that there is no better quality and comfortable material for pasting walls than non-woven wallpaper.

If you plan to use fillets to decorate the ceiling and walls, then initially you need to stick them on, and then start gluing the wallpaper.

How to glue non-woven wallpaper: technology

This type of material has the following advantages:

The width of the roll is approximately 1 m, as a result of which there will be much fewer joints in the room than when using conventional wallpaper.
Increased level of material wear resistance and abrasion resistance.
You can hide small cracks and other defects on the base of the wall.
If you want to change the wall decoration, old material can be easily removed from the wall when dry, that is, you do not need to waste time soaking the wallpaper.
High light fastness.
You can cover the wall from a roll. In this case, the working area will be reduced to a minimum.
Can be produced wet cleaning with improvised means.
The material is capable of transmitting steam and air, but it will not change its texture and size, which cannot be said about ordinary wallpaper.
Minimum amount of debris and dirt. This is due to the fact that the glue will need to be applied exclusively to the wall.
You can paint it many times, which allows you to change the interior design.
The material is made from environmentally friendly raw materials.
The wallpaper meets all sanitary standards.
The material can be glued both on walls and on ceilings.

Scheme for cleaning the wall from the old finish: a) cleaning, b) smoothing, c) moving the tool.

Before gluing meter-long non-woven wallpaper, you will need to measure the height of the walls. If the junction of the wall and the ceiling is decorated with a fillet, then it must be glued before wallpapering the walls.

The height will need to be measured from floor to ceiling or fillet, if the latter is used. To the value that will be obtained, you will need to add 10 cm for reserve.

On the wall from which you will begin gluing the wallpaper, at a distance of 1 m from the corner, you will need to mark a strictly vertical line, for which you need to use a plumb line and a long ruler.

A plumb line can be made with your own hands from a cord required length, and a heavy bolt or nut must be tied to one of its ends.

Elements that will be needed to glue the non-woven material:

The wall finishing material itself.
Construction sharp knife.
Putty knife.
Primer.
Putty.
Special glue.
Plumb line or long ruler.
Rag.
Meter.
Wallpaper roller or brush.

Carrying out all preparatory work

Before gluing wallpaper you will need to prepare the wall. You need to make sure that the wall is completely flat and has no bumps, cracks or any other noticeable defects. The base will need to be thoroughly cleaned of the old coating.

To make it easy to remove old wallpaper, you need to wet the coating. This can be done using water and a rag. The wetted material can be removed from the wall using a putty knife.

If the wall is not perfectly flat and you need to renovation work Before gluing the non-woven material in the corners and other problem areas, you will need to apply putty. After this, the wall must be primed with glue or a primer. deep penetration. If glue was chosen, it is recommended to make a weaker mixture.

Speaking about how to glue non-woven wallpaper, you should know that there are 2 basic rules that must be followed:

The surface on which you plan to glue the non-woven material must be dry and even.
There should be no drafts or air currents in the room, for example, from an air conditioner. All windows in the room must be tightly closed.

Next, you will need to prepare the material for gluing and painting. To do this you need to cut them into strips. It is important to remember that you need to leave allowances of 10 cm on each of the canvases. It is important to remember to follow the drawing, if necessary.

How to apply glue to wallpaper?

You need to start gluing the material from the corner, from top to bottom. In this case, you will need to sequentially smooth it in the vertical direction, using a roller or wallpaper brush.

You need to press lightly so that the new layer lies flush against the edge of the pasted one.

The glue will need to be spread on reverse side material, as is done in the case of regular wallpaper, but exclusively on the wall.

Scheme for applying glue to wallpaper: 1. Spreading the canvas with paste. 2. Fold the canvas in half.

It is important to choose the right glue that is suitable for gluing non-woven wallpaper. Any store employee who specializes in selling materials for construction and finishing can help with the choice.

It is important to know that the advantage of such material is that in this case it is not necessary to withstand a certain amount of time to impregnate the wallpaper.

This material can ensure stability of the shape and size of the sheets. Before applying glue to the wall, it is recommended to read the information indicated on the packaging of the adhesive mixture and on the wallpaper roll.

The glue must be applied to the wall, which has been previously prepared.

How to glue non-woven wallpaper: sequence of work

After applying the adhesive solution, you need to take the first strip of wallpaper, adjust it in height, and then stick it along the broken line on the wall. The other side needs to be turned at an angle. Don't worry if you can't get an exact match at the top of the wall because the wallpaper that will be sticking out can be trimmed at the end. First you just need to tuck them. Next, you need to start smoothing the material, expelling the air from under it. To do this, you need to use a wallpaper roller, spatula or a piece of clean cloth.

After smoothing, you need to take a wide metal spatula and a sharp knife. The spatula is used as a guide for the knife; it is applied to the joint between the wall and the ceiling. After this, you need to cut off the excess wallpaper with a knife. If you can't cut the damp wallpaper, you'll need to wait until it dries and then try cutting it again. If the wallpaper is not completely glued in some places, it may be necessary to re-glue the material.

How to glue meter-long non-woven wallpaper end-to-end?

Each layer is glued end to end with the previous one. In this case, problems will not arise if the wall was leveled at the preparation stage.

In the process of gluing a new layer butt to the previous one, you will need to adjust its height. A clear joint cannot be achieved by stretching the material. Even if you manage to do this at first, after the glue dries, the wallpaper will come apart.

If you can’t achieve a perfect joint and use monotonous wallpaper without patterns, you can use a trick. The canvas must be glued overlapping with the previous one, the intersection should be about 2-3 cm. Then, using a sharp construction knife, you need to make a through cut in the place where the canvases intersect. It is important to cut through 2 layers at the same time. At the end, you need to remove the scraps, coat the joint with an adhesive mixture and straighten the layers, obtaining an even joint.

How to glue wallpaper in hard-to-reach places and corners?

Particular attention should be paid to the process of wallpapering walls in hard to reach places. In this case, we mean the locations of sockets, batteries, switches and the ceiling. The edges of the wallpaper must be coated with an adhesive mixture to ensure that they are securely attached to the base of the wall. It is highly recommended not to allow the adhesive solution to get on the main side of the canvas. If for some reason this happens, you will need to quickly remove the glue from the wallpaper using a damp cloth. Next, the wallpaper must be wiped with a dry base.

You need to be careful when gluing non-woven wallpaper next to sockets and switches, as the electricity will need to be turned off. Before doing this, you should measure what size strips will be needed, and then cut them out.

After the adhesive mixture has dried, you need to make a recess in the hole. required sizes. Upon completion of all work, you will need to screw all sockets and other elements into place.

If you plan to glue this type of material to the ceiling, you should know that the technology is no different from wallpapering walls. The only difference is that in this case you need to find an assistant who can hold the wallpaper.

In the corners, the canvas must be glued so that the overlap on the adjacent wall is approximately 2-3 cm. If the layer is folded during the gluing process large sizes, then it must be cut with a sharp knife to the required size.

There are 2 options for how to stick this type of finishing material in the corners of the room:

The first method is used when you need to paste material with a pattern. The canvas must be glued from the corner, and the overlap with the other layer should be approximately 2-3 cm. The overlap can hide the defect if there is an uneven corner.
Another method is suitable for plain wallpaper. The canvas should be glued from the corner, then cut through 2 canvases with a knife, remove the excess and finally straighten the joint.

How to paint non-woven wallpaper correctly?

If, after wallpapering a room, you need to paint the material, then you need to know that water-based paints, which are resistant to abrasion and cleaning, are best suited. It is recommended to use latex or acrylic paints, which have the effect of silk. If you choose these materials, you can emphasize the texture features of the wallpaper.

The first coat of paint is applied approximately 24 hours after the glue has dried. To do this, you need to use a roller that matches the type of paint purchased. An employee of the same store will help you choose it. The second and all other layers of paint are applied after a few hours.

Gluing such wallpaper is quite simple, it is only important to prepare the base and follow the sequence of actions.