How to glue vinyl wallpaper and ceiling plinth. What to glue first, wallpaper or ceiling plinth. Among the advantages of the product we can highlight

In the question of what to glue first: wallpaper or ceiling plinth, – opinions differ. Fillet - - are needed to hide the gaps between the ceiling and wallpaper or other finishing materials on the wall. Yes, and they look very impressive. But there are some nuances to their installation.

Usually used for gluing to ceilings vinyl wallpapers and wallpaper for painting.

In order to decide what to do in this situation, it is necessary to consider the advantages and disadvantages of the options.

If you glue the fillets before the wallpaper, it will be easier to putty the joints of the baseboard and paint it, and you won’t be afraid to stain the wallpaper. But then it becomes difficult to fit the top edge of the wallpaper to the ceiling plinth. This must be done very carefully so that there are no gaps left.

On the other hand, if the wallpaper is already pasted, difficulties will arise with installing the baseboard. At least a day should pass after the wallpaper glue dries. Then the wallpaper will need to be covered with masking tape and glued, and then the baseboard will need to be painted.

First, the ceiling plinth is glued

The cut angles on both plinths, right and left, must be the same, i.e. their profiles must be identical.

As with any type of repair, you first need to take measurements and calculate the number of strips needed. The length of these planks is 2 meters. We round the perimeter of the room up and divide by 2.

The width of the skirting boards varies, so the choice should depend on the area of ​​the room. If the room is small, then you need to take narrow ones, since wide ones will look bulky.

Tools and materials for installation:

• ceiling plinth;
• liquid Nails;
• putty or sealant for filling seams;
• pencil;
• roulette;
• rubber spatula;
• miter box and stationery knife for trimming;
• glue gun.

To the wall with putty or liquid nails. If you glue it on putty, it will fill the existing cracks and you will only need to remove its remnants.

Before gluing fillets, it is necessary to carry out preparatory work, namely the walls in the place where the baseboard will be glued, then putty it.

For gluing, a special glue is used, which is applied in a strip to the sides of the plinth adjacent to the wall and ceiling.

Nowadays there is a wide variety of ceiling plinths; you can buy narrow ones, they are more flexible and follow the topography of the walls. In the finished version, this will not be very noticeable, of course, if the wall defects are small.

Theoretically, the corners of the rooms should be 90 degrees, but in practice this is not always the case. Therefore, we first cut the corners of the plinth at 45 degrees using a miter box, and then adjust it on site. Ceiling plinth made of foam plastic can be cut very well with a stationery knife. You can join one plinth to another on the spot and cut it off.

After cutting it, you need to, and then just glue it.

The joints need to be sanded with fine-grained sandpaper. The glued plinth can be left as is, or it can be painted water-based paint in the same shade as the ceiling.

Return to contents

How to wallpaper

Wallpapering walls, like any other endeavor, requires certain skills. As a rule, professionals are not involved in this process, but are handled on our own. It depends on how the walls are prepared for pasting, what wallpaper is chosen, and what glue will be used. final result– what the walls will look like.

Wallpapering tools:

For gluing, you can use two stepladders, which will be connected by a board at least 40-50 cm wide, or tables lined up in a row of the same height.

• pencil;
• scissors;
• roulette;
• painting spatula and knife;
• roller for joints and fleecy;
• glue tray;
• a bucket for diluting glue;
• soft cloth;
• plumb line with thread;
• table, stool or stepladder.

Before starting work, you must carefully study the instructions, since different types Wallpaper has its own rules.

The first thing you need to do is calculate the number of rolls. Now there are calculation tables, but they have large errors, so it is better to use the old method. Take an old roll of wallpaper with the width at which you plan to glue new wallpaper, and a tape measure. Then a measurement is taken along the perimeter from corner to corner, for walls with doors and window openings similarly. From one roll 10.05 m long you will get 4 strips with a wall height of up to 2.5 m. This calculation is applicable for wallpaper without joining the pattern, and with joining you will get 3 whole strips, the rest will be used over doors and windows.

A sponge or soft cloth will help smooth the wallpaper and remove air bubbles.

If necessary, the walls are leveled with putty, then a primer is applied. It is needed so that the glue is not absorbed by the walls and it is possible to easily combine the pattern on the canvases by moving the strips. Can be used instead of a special primer wallpaper glue, diluted to a more liquid consistency.

When cutting wallpaper, make a small reserve; they are carefully cut with a stationery knife on the floor. If adjustment of the drawing is required, then you need to look at the instructions, where the offset step is indicated, but it happens when this step does not correspond. So you need to test it on the floor first.

Wallpaper glue is selected according to the type of wallpaper. For areas near windows and doors, you can use a PVA-based composition. Dilute glue in a bucket with cold water according to the instructions, stirring quickly with a brush or stick. Let the glue sit.

Excess wallpaper is pressed with a spatula and trimmed with a sharp knife.

When wallpapering, the windows should be closed and the sockets should be de-energized. You can start gluing wallpaper pasted at the joint from any wall. For training, it is better to start with the one that will be covered with furniture.

The vertical is marked when gluing the first strip with a rope and a weight. This strip is glued from the corner with a 1.5-2 centimeter approach to the other wall. After the strip is coated with glue, it must be folded in half for impregnation. At this time, the wall is coated with glue and the strip is attached to it. The collected air is dispersed with a clean cloth or rubber roller.

Ceiling plinths should not be glued directly onto pasted wallpaper, as they need time to dry and are easily damaged.

The fillets are glued using the technology described above. The plinth for the ceiling performs not only a decorative function in the interior. It is also necessary for camouflage minor defects remaining after the final stage cosmetic repairs

. We are talking about the gap between the wall and the ceiling slab.

Choosing a ceiling plinth can sometimes be difficult, but installing it causes much greater difficulty for owners of houses and apartments. Next we will talk about how to properly glue ceiling plinths.

What should you pay attention to when choosing a gluing method?

The first and most important thing you need to pay attention to when choosing a method for gluing ceiling plinths is the material from which it is made. Because polyurethane, polystyrene and plastic, for example, are different in structure. This means that the means and methods of gluing them will be different.

The type of surface on which you will glue the baseboard should also be taken into account when choosing an installation method, since both walls and ceilings can be finished in different materials.

There are two main methods of gluing ceiling fillets. The first is that the plinth is fastened after finishing walls. For example, after it is covered decorative plaster or after wallpaper has been glued to it. It is worth noting that this installation method is the simplest. However, those who choose it should know that if it is necessary to paste the wall with other wallpaper or perform some other finishing work, the fillet will have to be dismantled along with the old one finishing coat and replace it.

Method of installing a plinth on top of wallpaper

In the second method, the ceiling plinth is installed before the wall is finished. Of course, in this case, wallpaper, paint or plaster will have to be adjusted to fit the fillet so that the joint between it and the wall is not noticeable. But this method of fastening is good in that there is no need to dismantle the plinth in case of re-finishing the wall. Therefore, it is ideal for installing more expensive fillets.

Gluing is done before finishing

Technology of gluing products from different materials

Most often for modern finishes plastic, polyurethane and foam skirting boards are used. Therefore, special attention should be paid to the process of their fastening.

How to install foam skirting boards

It would seem that how to glue a foam plastic ceiling plinth should not raise any questions. On the one hand, this is true, since they are the easiest to install. But on the other hand, achieving a perfectly smooth joint when installing even a foam plinth with a ceiling is sometimes not easy. And the point here is most likely not the lack of certain construction skills of the person making the repairs, but the fact that the walls in the majority standard houses uneven, which means it will not be possible to perfectly glue the fillet, which is made of fragile and brittle material, to the ceiling. What to do in this situation, and what method of fastening the plinth to use? Here step-by-step instruction for installing foam or polystyrene fillets:

1. You should start fastening by preparing the surface. If the wall contains residues of wallpaper glue or other stains, they must be removed with a spatula, sandpaper or mesh for grouting putty. If the joint between the wall and the ceiling has been puttied, before you are going to carry out the process of attaching the baseboard to it, it should be primed.
2. Installation of ceiling plinth made of foam plastic or polystyrene should begin with fastening the corners. And only then adjust the remaining parts to fit them. A special device called a miter box will help you cut corners correctly. In order to attach the foam ceiling plinth, you will need a similar shape that forms angles of 45 and 90 degrees.

1. Once the corners are cut, you can begin gluing them. To do this, you can use the moment of installation for ceiling plinths. Before installation, this or other glue should be applied pointwise and in small quantities, because excess glue that can seep onto the stucco molding can be quite difficult to remove, since it is not recommended to use household chemicals to clean it. Therefore, it is better to apply glue only to the middle of the product, and after gluing, seal the technological gap between the ceiling and the baseboard with sealant of the same color as the baseboard.

Joining the corners of the foam fillet while gluing it

1. The next step is attaching the fillets to the wall. Before attaching the ceiling plinth, it must be tried on and cut in the right places. Gluing is carried out in the same way as with fastening the corners. Do not apply too much glue so as not to stain the stucco during installation. Skirting board with adhesive composition should be carefully applied to the surface and pressed lightly. It is worth noting that the installation of foam plinth requires a careful approach, since this material is fragile and not resistant to damage. One careless movement and a dent or crack will form on the surface of your fillet, which after fastening will look unpresentable. This will require replacement, which incurs additional installation costs.

If you want to learn more about how to install skirting boards, the video below will clearly demonstrate this. It shows in detail the process of fastening foam products.

How to attach a plastic skirting board

When we talk about plastic, we mean two types of fillets - PVC and polyurethane. Since these materials differ in composition and characteristics, their fastening methods also differ from each other.

PVC ceiling plinth is good because the wires are laid in it during fastening, since there is a special box on the back of it.

Plastic plinth with a cable duct box and a wood texture, which is attached to a ceiling made of a similar material

The plastic plinth should also be attached from the corners. They can be cut using a miter box or bought ready-made, which are sold today in construction stores and greatly facilitate the installation process. This must be done before mounting to the ceiling. plastic panels or aluminum slats. Installation plastic skirting board It is made on a mounting strip located on the ceiling using self-tapping screws.

Installation of plastic fillets, they are glued in such a way that a finished corner can be placed between them

Less reliable, but more simple method is to fasten the fillet using sealant or liquid nails instead of self-tapping screws. It is worth noting that even if you choose the first fastening method, the seams remaining between the baseboard and the ceiling can be sealed with sealant. Remember that acrylic sealant should be applied quickly and preferably with wet hands.

If you want to clear example see how to glue a ceiling plinth, the video below will clearly demonstrate this to you.

Gluing a polyurethane plinth with your own hands is somewhat more difficult, since the weight of the material from which it is made is much greater. It is glued by analogy with foam plastic, with only one exception, which is the difficulty of choosing the adhesive composition.

Wide polyurethane fillet with stucco molding

It is worth noting here that most apartment owners are increasingly choosing liquid nails of the Moment brand, with which they can firmly attach the fillet to any surface.

Ceiling design process polyurethane baseboard should begin with surface preparation. After the remaining glue and putty have been removed from it, you can glue the fillets. Before making the corners from which the fastening process will begin, a layer of primer should be applied to the surface, the complete drying time of which is usually no more than fifteen minutes. Corners can be cut using a hacksaw and a miter box.

You can glue the corners yourself. This doesn't require much effort. It is enough to place a stepladder against the wall and attach the part coated with glue to the desired place. But attaching the baseboard itself to the wall is much more difficult. It is better to do this with two or three people in order to fasten the fillet faster and with better quality. Keep the baseboard coated with adhesive for as long as indicated in the instructions for use. Do not neglect to read it, because the quality of the repair depends precisely on whether you follow the rules for using the materials used.

After the installation of the polyurethane skirting board is completed, the joint between it and the ceiling should be treated with acrylic or silicone sealant.

If you need to become more familiar with the process of gluing ceiling plinths, you should definitely watch the video below.

When finishing walls and ceilings, the main attention is paid to the issue of their cladding. But don’t forget about the additional details that give the finished surfaces full aesthetic appearance.

One of auxiliary elements decoration - ceiling foam plinth (fillet).

Why do you need a ceiling plinth?

This product, along with other features, represents a worthy replacement of traditional paper edging, which in the past was often used for wallpapering.

Use of these products allows you to solve two main problems:

1. Practical. The fillet hides flaws in the geometry of the room (if any), as well as imperfections in the finishing at the joints between suspended ceilings and walls.
2. Decorative. The plinth gives the interior a complete look, and the use of elements suitable for general style premises, allows you to effectively complement its design. Thus, for an interior in a classic style, skirting boards with various relief patterns are used, and for decorating a room in a high-tech or minimalist style, narrow, straight products without a pattern are suitable.

Kinds

Ceiling fillets are issued in wide range and differ from each other both in size and material of manufacture.

Wooden

Suitable for classic interiors, as distinguished by an aesthetic and solemn appearance. Made from various types wood, ranging from budget coniferous varieties and ending with expensive woods (oak, cherry, etc.).

Among the advantages of these products are: environmental friendliness and presentability.

Disadvantages include:

• exposure to fungus and mold;
• lack of plasticity;
• difficulty in processing.

Polyurethane

Polyurethane flexible plinth approaches different styles interior, manufacture products in various forms and flowers. As additional decorative elements Consoles, columns and rosettes can be purchased for such skirting boards, which allows you to add splendor to the design of the room.

The products are not afraid of moisture, which allows them to be installed in the kitchen or bathroom. Of the minuses - high cost and soft structure, which requires special care during installation, since the product can be deformed as a result of strong finger pressure.

Read also about insulating the facade with polystyrene foam with your own hands.

Made from polystyrene foam

This type of fillet quality characteristics conditionally takes a middle position between products made of foam and polyurethane, since it contains the advantages and disadvantages of both materials.

The advantages of the product include:

• clear contours of the drawing;
• wide choice of reliefs, shapes and colors;
• reasonable cost;
• light weight;
• aesthetic appearance.

There are also certain disadvantages:

• products are hard and break easily;
• weak strength and low flexibility preclude their use for installation in shaped areas;
• need for painting;
• are easily exposed to chemical and mechanical influences.

PVC

Suitable for cases where the ceiling cladding consists of plastic or MDF panels. Skirting equipped with a special groove, into which panels are inserted during installation.

In order to join PVC skirting boards in the corners applies special fittings (corners), which greatly facilitates the work with these products.

Advantages:

• large selection of colors, shapes and textures;
• There are options on sale that imitate natural materials(wood, marble);
• hygroscopic properties PVC skirting boards allow it to be used when decorating bathrooms and kitchens.

Flaws:

• poor resistance to temperature changes;
• can only be mounted on smooth surfaces due to lack of plasticity;
• cannot be painted.

From foam plastic

The most budget products. They more susceptible to mechanical and chemical influences than others. This type of plinth is easy to install, lightweight, and resistant to rot and insect damage.

The disadvantages include:

• flammability and the release of acrid smoke when burning.
• After installation, it is advisable to paint the products to give them strength;
• inconvenient to care for, as it is made of soft material.

Dimensions

Width of ceiling fillets can be divided into three types:

1. Narrow. The width of the products is 1–5 cm. Suitable for rooms with high ceilings, as well as for use as decorative finishing of walls and niches.
2. Average. They will look appropriate in the design of rooms where the ceiling height is 2.5–2.7 m.
3. Wide. Products 16–20 cm wide. Used for decoration large premises with ceilings from 3 m high.

The length of the ceiling plinth can be from 1.2 to 2 meters.

Which ones to choose?

To solve this problem the best way, when choosing several criteria should be taken into account, namely the width, color and shape of the products.

Wide band visually smoothes the corners of the room, therefore it will take on a more rounded shape.

A wide plinth will allow you to hide maximum amount defects that may be located at the joints between the ceiling and walls.

A wide fillet is not suitable for a small room, as it will make it visually even smaller.

You should also consider combination of the width of the plinth with the height of the ceilings, as mentioned above.

For the right choice colors You should follow simple rules:

1. White color visually increases space and makes the ceiling higher.
2. The decoration of the room should have a maximum three primary colors, otherwise it will be excessively variegated.
3. Fillets of contrasting colors in a room with high ceilings will give it additional efficiency and originality. In this case, it is necessary that the color of the baseboard is in harmony with any other interior detail.

Form - this criterion is perhaps a matter of taste, since It's hard to say for sure which is better: simple, smooth products or fillets with a complex pattern.

Advantages of a simple form - versatility and practicality, which allows it to be used for any decoration. Patterned embossed skirting boards look good in classic interior or baroque.

It is also important to consider that with more complex shapes and patterns of ceiling fillets the fitting procedure becomes more complicated their corners.

To determine required quantity products, the perimeter of the room must be divided by the length of one baseboard. That is, if the length of the fillet is 2 meters, the perimeter is divided into two. To the received quantity it is desirable add 1–3 spare planks for cutting corners, scrap, etc.

Mounting methods

Installation of skirting boards can be done in two ways:

Let's look at this question: what is the best way to glue the ceiling plinth?

Selection of adhesive composition:

1. For foam and polystyrene foam products, acrylic putty or homemade glue, which is made by mixing PVA and finishing putty in a ratio of 1:4 with the addition of water.
2. Plastic skirting board can also be glued using acrylic putty or silicone sealant. When installing skirting boards on unfinished walls, it is better to use putty, and if there is cladding on the wall and ceiling surfaces, preference should be given to sealant.
3. For products polyurethane There are special adhesives that are designed specifically for this material.
4. Concerning wooden skirting boards, they are rarely used for a reason high cost and often heavy. If the products are made of light wood, they can be fastened with liquid nails, while heavier options require auxiliary fixation in the form of self-tapping screws.

How to glue fillets to wallpaper and suspended ceilings?

Installation of a stretch ceiling most often executed last after the wall decoration is completely finished. Therefore, when using wallpaper as wall covering, the baseboards are glued directly to them.

First of all, you should figure out how to properly cut corners on baseboards. The easiest way is to cut out the outer or internal corner on the ceiling plinth using a miter box. The cutting angle is will be 45°.

As cutting tool for products made of expanded polystyrene and polystyrene you can use a construction knife or a hacksaw for metal.

Angle cutting:

• one piece is inserted into the miter box on the right and cut off;
• the second is inserted from the left and cut off.

Skirting installation begins from one of the corners of the room. The part is applied to the surface of the ceiling and a line is drawn on the wall along the bottom edge of the plinth.

Glue is applied to inner part planks, which will be adjacent to the wall. After this, the plinth must be attached to the wall, guided strictly by the markings, and pressed well.

On uneven wall During installation, gaps form between the baseboard and the wall surface. In this case, the bar can be secure with masking tape, having previously pressed the product against the wall.

All other parts are glued in the same way. To improve the quality of installation with glue joints should also be treated plinths for better joining of products with each other.

To protect suspended ceiling from contamination during installation close it plastic film, which adheres well to the surface and is easily removed from under the baseboard after finishing.

With quality work done, glued skirting boards will blend harmoniously into the overall interior, allowing homeowners to put an end to the process of finishing walls and ceilings.

Watch the following video on how to glue ceiling plinths:

11833 0 0

What to glue first: wallpaper or ceiling plinth - expert opinion and tips on arrangement

Questions like: is it possible to glue ceiling plinth to wallpaper, or what is glued first and what then, are asked regularly on forums and other similar resources. So, there is no definite answer here. It all depends on the type of wallpaper, the material from which the baseboard is made and the condition of the walls. And then we will look at the most common situations, plus I will tell you how to install it all yourself.

Types of ceiling plinths

In fact, floor plinth It differs from the ceiling only in the material from which it is made. Strong, mechanically damage-resistant planks are installed in the floor area, and any kind can be installed under the ceiling, because there they are practically inaccessible.

Photo	Recommendations
	Paper skirting boards. This edging is also called a frieze or border. At a stretch, decorative paper strips can be classified as skirting boards, but formally they are considered such. In terms of order, the paper border is always glued on top of the wallpaper.
	PVC skirting. Plastic baguettes are mounted on the ceiling only if the ceiling is sheathed with the same plastic. As you can see in the photo, they even have a groove for such panels. These baguettes are attached either to the sheathing or to the ceiling. As for wallpaper on the walls, before filling the wallpaper, the plastic is simply folded back and the wallpaper is glued. Formally, here the plinth is mounted on the wallpaper, although the fillet is attached to the ceiling.
	Polyurethane moldings. Flexible polyurethane baguettes are now considered the most popular. The material is light, durable and at the same time elastic. Such baguettes cannot be distinguished from the same plaster, and they can be mounted both on and under wallpaper. We'll talk about the intricacies of installation a little later.
	Plaster stucco. Before the advent of polyurethane and foam, gypsum was extremely popular. The baguettes are beautiful, but quite fragile and heavy, which makes them more difficult to install. In no case should gypsum products be mounted on top of wallpaper.
	Foam edging. If installed correctly, foam moldings cannot be distinguished from plaster or polyurethane, but their price is more than affordable, plus anyone can glue them to the ceiling. People often glue foam fillets to wallpaper so that when they change the wallpaper, they can also replace the fillets, because foam plastic is cheaper than wallpaper.
	Wooden fillet. Wooden edging is now considered elite. Such skirting boards are often attached to the base with dowel nails, the problem is that they need ideal smooth walls and ceilings. If, for example, the distortions under a plaster border can be covered with putty, then this trick will not work here.
	Stone border. Marble, granite and other stone products cost fabulous money, plus they are very problematic to install. As for wallpaper, firstly, not every canvas will fit under a stone frieze, and secondly, heavy stone is never mounted on top of wallpaper.

Subtleties of arranging different options

1. Flexible and lightweight - this includes polyurethane, foam and polyvinyl chloride. This direction can be mounted both on top of wallpaper and end-to-end with the canvas;
2. Hard and heavy - here we have plaster, wood and stone. All of them are mounted end-to-end only. The fact is that not a single wallpaper, even the densest one, can withstand such weight, plus it is often necessary to level the walls under hard baguettes.

When and how the fillet is attached to the wallpaper

Experienced craftsmen are strongly against this approach, because this is, in fact, a one-time option. If you start changing the wallpaper, you will have to remove the frieze as well, so it turns out double work. But people are afraid that without experience they will not be able to beautifully arrange the joint between the baguette and the canvas and glue the baguette on top.

But let's return to practice: let's start with the fact that the baguette can only be glued to non-woven wallpaper or vinyl wallpaper; the paper can only withstand a thin foam frieze, nothing more. I'm glad that the instructions are the same in all cases:

• The frieze is glued on top of the wallpaper after the walls are completely dry, which is about 2-3 days from the end of gluing;
• 1-2 strips of thick universal glue, such as “Moment-montage”, are applied to the back side of the baguette, after which the baguette is applied to the junction of the ceiling and the walls and held for about 30 seconds;
• If glue oozes out from under the baguette, it is immediately wiped off with a soft rag.

Another common question is how to remove the ceiling plinth without damaging the wallpaper? I will say right away - this is unrealistic. If the baguette is glued, then when you try to remove it, it will tear the top layer of the canvas. And if the strip is screwed on with self-tapping screws, which is also possible, then the screws have already gone through the canvas and it is damaged.

Installation of fillets end-to-end with the canvas

First, we need to secure the fillet itself, and only then join the fabric to it. Foam, polyurethane and gypsum fillets are glued. Polystyrene foam and polyurethane are glued with universal glue, gypsum is attached with gypsum mortar with the addition of PVA.

• Before installation, the wall is treated with a strengthening primer, otherwise the glue will not adhere well;
• When the soil has dried, apply glue to the fillet and fix it on the wall;
• If the wall is curved and there are noticeable gaps under the plank, you need to cover them with putty, after which you can start painting the baseboard.

A separate topic is going around corners. “Sofa” craftsmen advise cutting the slats using a miter box, I categorically do not recommend doing this, the corners are almost always crooked and there will be a gap between the slats.

A proven technology for trimming skirting boards in corners looks something like this:

• First, apply the strip to one side of the corner and draw an edge on the wall and ceiling;
• Then do the same on the other side of the corner;
• The intersection of these lines will be the cutting line. This technique works for both interior and exterior corners.

Foam plastic is a very light material used for the manufacture of various finishing elements, including baseboards. The use of this detail gives a completed look to the renovation and serves as a unique decoration for the room, adding sophistication. Therefore, when working, many people have a question: and how?”. You will find all the answers below.

The first method is gluing onto a putty compound.

• Skirting board. The type of this element is selected individually, it is important to consider the following - for small rooms with low ceilings you need to take a narrow plinth, and for large rooms with high ceilings, a correspondingly wide one.
• Putty. Many of those who carry out repairs on their own do not know what to glue the foam plastic ceiling plinth to, and therefore buy a special solution. Remember: putty is well suited for gluing the ceiling element. There is only one requirement for the mixture - it must be suitable for work, with good timing suitability.
• Primer. To firmly secure the element to the base, the surface should be well prepared, and an acrylic-based primer mixture is best suited for this.

Required Tools

In addition to materials for gluing, you will need some tools:

• Hacksaw with fine teeth. It is recommended to cut foam plastic with a tool for working with metal, since using, for example, a construction knife will not allow you to achieve even and high-quality cuts.
• Miter box. This is a special device for obtaining ideal angles.
• A spatula up to 10 cm wide. Needed for applying putty.
• Brush for covering the surface with primer.
• Sandpaper. Fine sandpaper is ideal for removing rough edges.

The process of gluing skirting boards

So, how to glue a foam plastic ceiling plinth? The procedure consists of several steps:

• Check the junction of the ceiling and wall for irregularities. If found, they should be eliminated.
• Primer treatment. The surface on which the plinth will be installed must be treated with the mixture using a brush.

Advice! It is recommended to pre-designate the area where the plinth will be located by outlining its position with a pencil. Thus, during work, clear guidelines will be visible, which will help to avoid uneven gluing of the element.

• Measuring the exact length of the skirting board. This process is extremely important, since an error of even a few millimeters can lead to cracks at the joints. Therefore, this step should be taken with maximum responsibility.
• Cutting skirting boards. After precise definition dimensions on the elements should be marked for subsequent cutting. At this step, it is important to properly fix the plinth in the miter box so as not to spoil it. Follow the instructions included with the tool.
• Preparing putty. After the plinth is ready, you should proceed to making the mixture. The putty must be diluted with water in the same way as for finishing works, the composition should be homogeneous and moderately thick.
• Applying the mixture. Now the putty must be applied to the side of the baseboard that will be attached to the base. The layer should not be thick and applied evenly, otherwise when you press on the element, excess will come out from all sides, which will have to be removed.

Gluing the baseboard

The whole process consists of several steps:

• Don’t know how to properly glue foam ceiling plinths? Everything is extremely simple: you should start from the most visible place from the corner, applying the element to the surface and pressing tightly. If excess putty does appear, it should be removed immediately before the composition hardens.
• Sealing cracks and joints. In the process of eliminating excess composition, all defects are simultaneously repaired. This is done like this: the baseboard is carefully leveled, and the cracks and joints are sealed with excess putty. This is the first advantage of putty.
• Don't know how to glue the corners of a foam plastic ceiling plinth? It is important to do this end to end. Gluing the next element is done in the same way, with the only difference being that before gluing the part to be joined, putty must be applied to the end area. Thus, it will be possible to simultaneously seal the connection and fasten the elements. It is important to combine them clearly so that the resulting overall geometry is ideal; the slightest displacement will be very noticeable.
• Removing irregularities. If, after drying, irregularities have formed at the joints, they should be carefully removed with sandpaper.
• Primer. After leveling, the baseboard should be covered with a soil mixture.
• Coloring. This is the final stage - the plinth is painted in the desired color.

Now you know what to glue the foam plastic ceiling plinth to. Tips for using the first method:

• To protect the wall and ceiling from paint, stick it around the perimeter
• When gluing the foam baseboard, do not press it hard with your fingers, since it is made of a very soft material, marks may remain. It is best to press the element with the back of your hand.

Method two: using glue

This method can be used on both covered and bare walls. But in the first case, it is important to take into account that the wallpaper must be glued securely, otherwise the wallpaper and baseboard will fall off.

So, what is the best way to glue a foam plastic ceiling plinth? There are several options:

• Universal assembly adhesive. It is a slowly hardening transparent mass that is used for various types of materials. The most popular option is the composition for polystyrene “Titan”. This glue has significant drawback- inconvenient operating principle: the composition is applied to the surface, after which you need to apply the baseboard and wait for adhesion, holding the element with your hand.
• Don’t know what to glue the foam ceiling plinth to? You can use liquid nails. This perfect solution when choosing the second method. The composition is produced in several versions: in the form of a pistol and in tubes. To work with foam baseboards, it is recommended to use liquid nails for polystyrene foam products.

What to do if there is no glue?

What else can you glue foam ceiling plinths to? When you have neither glue nor putty on hand, you can use acrylic sealant. This composition has the necessary viscosity and reliably fixes the elements. In addition, at acrylic sealant there are very important advantage, which you will learn about below.

How to glue a foam plastic ceiling plinth: the second method

There is no point in talking about what tools are needed, since the pepper is almost the same as in the first case, with the only difference being that you don’t need a spatula.

Scheme for gluing the plinth:

• Surface preparation. The first thing to do is check the surface for flaws. If identified, they should be eliminated so that the baseboard fits more tightly to the wall.
• Measuring work. After this, the lengths of all elements and the marking of the wall are measured to make it more convenient to work (the process is described above).
• Cutting skirting boards. The operation is performed using a miter box.

Interesting! If you don’t have this device at hand, you can make it yourself. To do this, you need to take a sheet of cardboard or paper and draw the corners (it is important to do this correctly). Working with such a “tool” is much more difficult, but still better than nothing.

Pasting process

Now you can begin the most interesting part, namely the gluing process.

• Applying glue. The best way to glue foam ceiling plinth is described above; please note that if the choice fell on liquid nails, it is recommended to purchase a gun, this will greatly facilitate the process of applying the composition. Glue is applied only to those surfaces that will be glued. If the elements are attached only to the wall, then the glue should be applied only to one side.
• Gluing elements. The skirting boards are carefully placed in the gluing area and secured according to the instructions for working with the composition. The principle of gluing may be different depending on the glue, in some cases you need to press the element and then remove it for a while to set the composition, in others it’s enough to hold it for a few seconds, and that’s it, the glue has set (such options are preferable, this includes sealant, and this is what there is an advantage).

• Sealing cracks and joints. The baseboard remains until the glue dries completely (the time is indicated on the packaging of the composition), and then it is necessary to repair all the irregularities and cracks that may have arisen during the process. To do this, a sealant is used, which is applied to the desired areas; excess can be removed with a spatula or finger. As a result, the joints are smooth and neat (this is another advantage of acrylic sealant).
• Coloring (if necessary). Don't forget that before you start painting the baseboard, it is recommended to first coat it with a primer. If you do the work carefully, the frame will look perfect, since the baseboard itself and the sealant have White color. And if there are no flaws on the surface, then the joints will not be easy to see against the general background.

Masking joints and painting

Since many people are very concerned about the issue of processing joints, it is worth discussing it in more detail.

If, after strengthening the ceiling plinth, gaps form between the elements, this is not at all scary, since they can easily be eliminated by rubbing in regular white sealant. If the ceiling has not yet been whitewashed or painted, then the most The best way masking the shortcomings is as follows:

• All glued baseboards must be covered with light putty using the same technique used for painting.
• After drying, the excess can be removed using fine sandpaper or a special sanding sponge for plaster work.
• As a result of this finishing, the ceiling and moldings will turn into a single whole without a single gap.

Coloring

After you have figured out how to glue the foam plastic ceiling plinth, and that’s it installation work have been completed and the shortcomings have been eliminated, you can safely move on to painting the baseboards. It is worth noting that this step is not mandatory, but rather has an individual character; a painted plinth will give the ceiling a finished and more attractive look.

Before deciding whether to paint or not, you should understand that, for example, a white baseboard should always be painted, because otherwise it will acquire a yellowish tint over time, which looks very ugly.

Rules for painting skirting boards

Most people decide to paint a ceiling element, so the rules below will be very helpful.

• For this procedure, water-based, acrylic or latex paint should be used. In some cases, you can choose nitro paint, but in this case the surface must be primed.
• For better adhesion, elements should be painted no earlier than 24 hours after gluing.
• It is recommended to paint the baseboards before wallpapering.

There are often questions about what is the best way to glue a foam ceiling plinth, and they also ask about whether there is a self-adhesive ceiling plinth. To date, such options are unknown, there are only flexible elements for the bathroom and floor covering, therefore ceiling structures will have to be installed using traditional methods.