Fast installation door. How to put interroom doors: step-by-step guide. Types of door boxes of interroom doors

Sections Articles:

Success in self-installing interior doors can be achieved if you properly approach the solution of this task. On the one hand, such work is easy to produce, but on the other there are a number of nuances that need to be taken into account during the installation process. Before installing the interior door, it is important to consider the actions algorithm. At the same time, if it does not prepare work, it may affect the final result. Great importance It has theoretical preparation in the matter how to put such door structures. Even in the absence of experience can be installed interior doors Competently and reliably.

Preparatory work

Before studying the theory of the installation of interroom doors and proceed to the installation of the structure, it is necessary to consider the issue of preparatory work. In no case cannot ignore this stage, otherwise simple and fast installation Doors can turn into a real nightmare. First of all, you need to pay attention to two points.

To begin with, you should make sure to complete door Block Open. The optimal situation will be if after mounting the design from all of its sides, the gap of 2-3 centimeters will remain. It will make it possible to easily put the door frame in the same plane level with the opening.

To achieve this is easy. If the open is too narrow relative to the door block, it can be expanded with a perforator or shock drill. In the case when doorway too wide, then there is an opportunity using wooden bar Reduce its dimensions. In general, the clearance of up to five centimeters is normal.

For the perfect installation of the door block, you can use one simple device. It is required to attach across the box three smooth wooden rails. One bottom, second from above, the third is in the middle of the design. These rails will allow you to put the door block in one plane with the opening.

To avoid damage to the surface of the door frame, you can fix the rails by putting under them wooden lining. They should be screwed to the end of the box. In addition, the length of the rail must be chosen in such a way that after installing the door frame in the opening, the rails rested in the walls. By the way, it will be that there are some more nuances that will help to install without unnecessary difficulties.

First of all, the rails are required to be fixed on the side of the door block into which the door will open. In addition, they must be fixed after installing the door frame in the opening and formation between the logging and the opening of the gaps of the desired size.

To fix the box, you can use the folded twice tight cardboard. It is very important at the preparatory work stage to perform two actions described above. Without the implementation of these procedures, it is not recommended to install the door block, because in this case, the risk of skewing the entire structure increases significantly. After the implementation of these manipulations, you can proceed directly to independent installation Interior doors.

Independent installation of interroom doors

After the completion of the preparatory work and the workpiece of all required tools, You can start the installation of interroom doors. From the tools you will need a hammer, a non-sleeping rack and a fombus. In addition, it is necessary to purchase a balloon with mounting foam low pressure With polymerization. As an example, it is possible to make a foam macroflex 65. It should also be prepared by a wedge of wood. To date, there is a spent technology, how to put interroom doors correctly. The installation process can be found in the video.

First of all, you must put the door block in the opening. During this process, it is important to pay special attention to the part of which the design is established. It is desirable when making installation is where the door will open. Now you should set the design in the center of the day. Moving the door unit to the right or left it is necessary to provide the same gaps between the design and walls on both sides.

At the next stage, you will need to make sure that the vertical location of the door frame racks. To do this, you can use the Rack Level. It must be applied to the bottom of the top transverse jumper. If the level is not followed, it will be necessary to take advantage of the bag, lifting with it the desired rack and resting wooden wedges under it.

After that, the door block should be fixed to partitions. To do this, drill holes with a diameter of 6 mm in the protruding part of the wooden jumpers. Then the dowels are clogged into these holes. In the process of fixing the door block, it is necessary to check the position of the structure relative to the side walls from time to time.

After that, you should wet the water box and the disc. Such a procedure is carried out in order to increase polymerization mounting foam And its adhesion with the walls of the day. Then you need to make sure to preserve the correct position of the door frame. To do this, use a rack level. In addition, it is necessary to control the presence of pads made from cardboard, between the door cloth and the lodge. If some fell out in the process of performing work, they must be returned to the place.

At the next stage, it is necessary to fill the gaps between the door block and partitions using the mounting foam. After that, you need to give foam to grab and dry out. This will require several hours. As a rule, the mounting foam is completely freezing for 6-10 hours. It will be by the way to say that the mounting foam is a poisonous material. To avoid the unpleasant consequences of skin contact with it, you can use protective gloves. In addition, it is necessary to protect the surface of the products using a painting ribbon, placing the door block around the perimeter.

After that, it is necessary to remove all aids. Now they are no longer needed. So, with the help of dumping, dowels and self-tapping screws are dismantled with which jumpers are fixed in the door frame. Then you need to remove the rails themselves and open the door. Cardboard linings must fall on the floor after opening the door.

Decoration of doorways

The question is how to properly put the door blocks is not limited only to the installation of the structure itself. After the interior doors are mounted, it is necessary to carry out work on finishing door Piece. The method of implementation of this procedure depends on the width of the doorway, as well as the type of the mounted door block. In the case of a subtle simpleness, such as, for example, at the entrance to the bathroom, you can make a finish using single platbands. This option is the easiest and easy-to-see. The acquired platform kit is fixed on both sides of the door design, covering the gaps filled with foam between the box and partitions.

If we are talking about wide door Opeters, their finish is carried out with the help of the same platbands or volunteers. They may differ from the color of the door leaf, the more recently contrasting solutions have become popular. The sentiment can be cut into the desired width, and it should be fixed using the construction glue.

In addition, it is worth emphasizing that one of the ways to finish the doorway is shuttering. This method is especially appropriate when installing wooden door blocks. The fact is that cement-sand plastering Favorable emphasizes door structures from natural wood. At the same time, this type of finish is not recommended for door boxes from fiberboard. This material is not compatible with high humidity Materials that are used in plastering.

After installing the door block, the installation of platbands own hands Does not represent much difficulty. It is necessary to cut the edge of each platband at an angle of 45 degrees and consolidate them on the door frame. For these purposes, you can use glue, finish carnations or self-tapping screws. Covers are subsequently rubbed, and self-tapping screws are hidden using decorative plastic plugs.

As practice shows, the installation of interroom doors is quite simple procedure. But, only subject to the compliance with the installation technology and the sequence of work. Reasonable approach to the case will allow all manipulations without special efforts and problems.

Caring for interroom doors

It is important to remember that technically competent and neat installation of interroom doors can easily be leveled by the lack of care for design and improper operation. Interior doors are recommended to use indoors at a temperature of +15 to +35 s °. In this case, the humidity of the air should not exceed 70%. It is important that there is no sudden temperature fluctuations and moisture differences in the apartment on the door block.

It will be emphasized by the way that special attention should be paid to the operation of interroom doors in rooms equipped with hermetic windows. If you do not air the rooms, there may be excessive humidity in them, which is likely to be the cause of damage constructive elements Door design. So, the door can wake, the material of the finish is cut off.

In addition, installation is strictly prohibited. MDF doors In those rooms in which there is a constantly elevated air temperature and humidity. Such objects include pools, saunas and baths. At the same time, it is not recommended to establish such structures in rooms without heating, with cement or earth floors. At the same time, it is allowed to exploit interroom doors with a short-term impact of moisture. In this case, the prerequisite is ventilating premises. As an example of such an object, you can bring the bathroom.

In the course of using interroom doors, the opening and closing of the web should be made exclusively in ways that are not entitled damage to the design and platbands. In addition, even if the door is equipped with a wear-resistant castor coating, a coarse mechanical impact on the design should be avoided. Otherwise, probably the appearance of chips, cracks, burr and pulp. Such defects will deteriorate significantly aesthetic species Door block.

Interior door, like furniture in the room or other interior items, needs careful attitude and attention. To preserve aesthetic appearance of the design, it is enough to periodically apply special means Care. Clean the door block from dirt and dust is necessary with a soft tissue or wet napkin. Contact design with various solvents, acid and alkaline compounds should be avoided. If you stick to those simple rulesThe interior doors will delight their owners aesthetics and long service life.

In conclusion, it is advisable to emphasize that the whole process called "I put interior doors on your own", produced in compliance with the technology and recommendations of professionals, will take about three hours. True, this is not counting the time spent on preparatory work Before you start installing the design with your own hands.

Own forces to make installation of interior door - work is not difficult. Below will be described simple step-by-step schemestarting from the choice in the store you like the interior door and finishing independent installation Interior doors with step-by-step photos.

Interior doors can be divided into several types

On the market manufacturers door structures offer pretty wide the lineup. Ready interior doors can be made of different materials. Most often are the following types of materials :,,

1. Fiberboard - Door: The frame is made of wood, and is trimmed sheets of fiberpo with lamination. These doors include such doors: a low cost relative to other species, a small weight that makes it possible to deliver them from the place of sale to the house on their own, ease of installation. Considering these moments, they are successful among buyers, thanks to a wide range of Most often presented in stores.

Of the minuses, it is possible to note the low strength of the DVP itself, because of which the door breaks and becomes unusable pretty easily, poor resistance to humidity, the door can twist. Therefore, we do not recommend it in bathrooms with a weak exhaust, this material loves dry rooms.

Photo - MDF doors models

3. Natural wood - Interior doors made from such material are the most durable. Their price directly depends on which breed of wood was used for their production. Doors out valuable breeds Woods are used to install indoors with author's design, they will fit perfectly in classic interior. The width of the interior doors is selected for the sizes of your opening.

Photo - Wooden Doors Models

The list of interior doors by type can be added, steel, but these species are not very popular among the wide masses of the population, so they are not included in the article for a detailed description.

Come here if you are interested and.

Types of door boxes of interroom doors

The correct interroom door should stand in a reliable box for the door, because from its quality will depend on how long the door will last, as well as the design of the doorway of your room. Door boxes can be divided into three main types.

1. Box of fiberboard. It looks pretty decent, but when choosing a box of this material In question, the strength of the whole design. The middle of the boxes of the box begged on their weight, not to mention possible defamation from the weight of the door canvase itself. Since the main components in the Fiber W, if we speak in simple, are glue and paper, it is necessary to take into account that they are very fragile and not durable. They are not recommended to hang the doors from the tree and the MDF due to their greater weight.

Photo - Box of fiberboard

2. Unprocessed wood. The cost is at the level of boxes from the fiberboard, but unlike the latter, the boxes made from a dry profiled timber have a higher strength. Therefore, when choosing between boxes of fiberboard and unprocessed wood boxes, we recommend to stop your choice on the latter. It is also necessary to take into account that you will need additional materials for the final finish of the box.

Photo - Unprocessed Wooden Box

3. Laminated wood. Does not require final finish, as it is already laminated by paper. And here there is one important momentWhen choosing such a box, the quality of lamination is very important. If thin paper was used for this, there is a high probability of scratching, scratches, cracks, the coating loses its appearance. Perhaps more qualitative option There will be a box of untreated wood with self finish treatment and painting.

Photo - Laminated Wooden Box

Also, the entire doorway interior door may require additional processing After installing the doors. Everything will dwell from your opening, its size, the location of the doors in it, the interior of the room.

For such treatment, you can use a challenger and platbands. Necessary kits can be bought in the store. We recommend it to be determined with their need after the final installation of the door to understand what exactly final finish You need. After all, buying additional Materials - These are additional costs that may end up not needed.

The door is considered for an example with a box of fiberboard. If installation is required wooden klyobov, it is necessary to work according to the same steps. Installation will be simpler, as the wood is stronger than DVP.

Step 1. Selection Tools and the necessary additional consumables. For installation you will need:

• saw;
• electric drill ();
• drills 3 mm and 4 mm on wood;
• bras 4 mm and 6 mm on concrete;
• screwdriver;
• roulette;
• a pen;
• screws on a tree;
• dowels fast mount;
• foam assembly.

Step 2. Determine the circuit for fastening the box in the doorway of the interior door.

Photo - Diagram of fastening the door box in the opening

The figure shows the fastener scheme of the door box in the opening. As we see, the interroom door (2) is installed in the box (1), which is fixed in the opening on the screws (3). Between the wall and the box we blow foam (4). The process is as follows: Install the box in the opening, fix it with the wall, we throw.

Photo - Disassembled door frame and door before mounting

If, after installing the door, it will not be able to hide it in the floor, choose a box without a clamp for convenience. P-shaped. It does not have a lower crossbar therefore bothering you will just have nothing.

Step 3. Assembling the door frame.

Photo - Doorfire for easy installation must be assembled

Loops must be attached to the purchased box. The door should be cut down the handle, as well as under door lock Interior door. We start assembling the door box. You need to connect all parts of the box together and fit under the dimensions. The factory length usually goes with a reserve of 5 cm.

The surest option is not mistaken - the assembly of parts on the floor as they should stand in the doorway. Special attention must be paid to metal bases Loops, they must stick up, so that they could hang the door on top.

Select the side of the opening, depending on the premises, between which doors are installed. From small rooms, such as bathroom, pantry, doors better open outwards, from large rooms In the corridor - inside.

Photo - the right position of end slats

We attach the top bar on the tapping screw. Face planks (1) must lie through the line. If no lines, then the bar is incorrect and you need to deploy it.

Photos - Screws twist after pre-drilling

Considering the structure of the Fiberboard and the characteristics of its strength, in the box, before screwing, it is necessary to drill holes with a drill on a tree with a diameter of 3 mm. This action is carried out that our box would not crap during the assembly process. For the same reason, the place of attachment of screws should be closer to the center, away from the edges and corners.

Photo - Collected box

For fasteners, the bar will have enough sleds, two on each side.
If the door lies horizontally on the floor, put under it soft fabricSo you reduce the likelihood of damage to the laminated layer.

Photo - Measurement Height Measure

Photo - Line of the extra box of the box

Speaker surplus better trim manual saw. The automatic saw is preferably not used to avoid damage to the coating.

Photo - Trimming Surplus Hand saw

As a result of all manipulations, we get a P-shaped door frame, ready for installation in the doorway interior door.

Photo - Wooden box assembly

Step 4. Installing the box in the opening.

Put in the doorway. Align in level. The correctness and evenness of the box assembly is checked by hanging the door on the loop, and closing it.

Photo - checking box level

Photo - Drill diameter 4 mm on wood

The box installed in the opening must be secured by self-draws. Remove the end decorating bar and drill 7-8 through holes on each side. The distance between the holes is 25-30 cm.

Photo - drilled box

The tree drill is not designed to drill the walls, only a box of fiberboard drills. After that, check the position of the box again using a level, since during the drilling process it could shift. If no changes are starting to drill the wall. Via thin drill On concrete with a diameter of 4 mm, through the holes in the box, we apply markup on the wall. Fully drill the wall through the box is impossible, as you can damage it. The diameter of the hole is 4 mm, if you do more, the hats of the screws will fall out. Next, remove the box with the opening and begin to make holes using a 6 mm diameter. If the simpleness is brick, the holes for installation should be in solid brick, and not in a masonry seam, in which the dowels are very bad.

Photo - drilled brick simple

Photo - Dowels in solid brick

Photo - Self-tapping screws for quick installation - Left, Self-tapping screws - Right.

Dowels are mounted in finished holes. Fix the box in the wall with the help of screws. For convenience, you can use a screwdriver or drill with a nozzle under the screw screw. Self-tapping screws are not completely screwed, a box deflection is possible. In order to avoid the deflection, the lining of wedges is possible. To check the levels and lack of distortion, in the process of screwing the screws, additionally check the box in terms of level.

Photo - Lining Kliniev

At the end of the installation, the box is checked from the side of the room using a level.

Photo - Check box in level

Step 5. Installing the door on the loop.

How to put the interroom door? Enough to dress the door on the loop

If it is a door from the fiberboard, taking into account its weight, it is possible to make one. After installing it, let's try to open and close. In the closed position, the gaps between the box and the door should be about 3 mm.

Photo - Check availability of gaps between the box and door

Photo - Closing and opening doors - light, without distortion

The lock is carried out in the interroom door. And also setting the handle.

Step 6. Filling the seams by mounting foam.

An important step is to fill the gap foam between the wall and the box. It needs to be carried out at installed door. In the process of drying, foam increases its volume. If you overdo it with its number, it can snatch the screws, rumble the box and the door cannot be closed. Everyone will have to cut and start the installation again.

Photo - Cardboard in the gap between the door and the box during the gate

Swimming seams is the most simple work. Vertical seam is filled from below. You need to be attentive to the volume of filling. Foam is capable of increasing its volume when drying. Therefore, you need to fill out the third part of the space between the door frame and the doorway interior door. When overroclaiming, damage to both the box and the design as a whole is possible, as the foam can get on the front of the box and the door and spoil their appearance. The complete pouring of the mounting foam occurs within 24 hours, the required temperature of 20 degrees.

Photo - widespread opening plaster

If the wood blade is installed, possible option Finishes may be the plaster of the slope (1). Cement-sand plaster profitable will emphasize your choice of doors from natural tree. But it is not recommended to be used for boxes of fiberboard, as they are not compatible with high humidity of materials that are used for plastering.

Installation video for interroom doors

Submitted our reader Herman.

Step-by-step installation of interroom doors, not counting the training time will take about three hours.

In the house and apartment there are elements that their external species Create dramatically change the stylistics of the entire interior, visually change the spatial proportions of the rooms or serve as the center of perception of the room. One of these elements are interroom doors. It is they indicate the end of one zone and the beginning of another, and also help to ensure a sense of privacy.

Any errors made in the installation may dramatically lower the quality of repair, so the doors should be treated with full seriousness. This process is quite time consuming. To fulfill it yourself, it is very much to do, but only real professionals are capable of doing it with a qualitative and small flaws. For impeccable installation, it is necessary to master new technologies for mounting doors, which appeared over the past years.

The main tasks and new methods of their implementation

When installing there are several standard problems that invariably accompany this process. They are not new, and they always had to decide. But now, with the advent of new approaches, technologies and tools, it has become much easier. The main ones are:

• high-quality dismantling;
• uneven doorway;
• locking lock;
• inserting loops;
• dunning door handle.

With the advent of new technologies, the majority of these tasks have become much simpler, now it takes much less time, and the time factor is a very important indicator during repair or construction.

Dismantling

As a rule, before the installation itself, dismantling the former design. In order for all further steps to be immaculate, it is necessary to remove old door, loops, platbands and an old door frame, even if its replacement is not provided. In the case when this component is replaced, it is worth a little to write it in a convenient location.

All elements of the old finish must be carefully cleaned. With the use of spatulas, it is necessary to remove the cement and plaster, which peelled or fit loosely. From how high quality in this zone is made wall coatdirectly depends on final result Total mounts.

Increasingly, after dismantling the old interior door, the plaster of slopes is updated. The level and technology of execution of this stage depends on the aesthetics of the installation and the convenience of further operation.

With the help of plaster, it is possible to eliminate small gaps between the box and the door of the door. The largest cracks first mask using plate mixand then plaster. These measures improve sound insulation and thermal insulation indoor space. In addition, the absence of the smallest cracks prevents dust and small sera, which can move into a room with air flows.

Watching transforms slopes and makes completion in the interior. If in the future the finishing of this space by wallpaper, tiles, any type of panels, then this stage is mandatory.

Overlook the doorway is a very common situation. According to statistics from 10 such designs, only 1 is initially smooth, therefore, it will be necessary to align the punishment almost for sure. Check the level of walls, slopes and other design elements are now very easy with laser level - appliance high precisionwhich is useful at many stages of construction.

The door canvas should navigate strictly vertically in a single plane with a box, since any skew in as soon as possible It will be aggravated, the degree will increase, the door will become known, which will affect its operation. This defect can completely interfere with closing.

If the doorway does not comply with these requirements, then the cash will not be established without problems: on the one hand, the slots are drawn, and the protruding wall will be disturbed.

Corner cash

New technologies for the installation of interroom doors offer installers to apply angular navigate. It is one of the corner in the prepared grooves, which are provided on the box. Thanks to this, the groove box is installed only as it is necessary, in the same plane. Such a system guarantees strictly vertical orientation of the canvas, smoothing all possible errors.

Corner platband with card loops

The box with grooves is placed with the overall surface of the day, while the other side is reliably blocked by the angular platband. This allows you to solve all problems with the goodness, besides, there is no need for the subsequent build-up of the depth of the box.

If the groove does not allow you to fully enter the platform, then the protruding outward cut off, after which the density of the adjustment to doorway It becomes perfect.

Previously, the process of the inserts of locks demanded manually to make significant in size of the recess using the chisel. Now this procedure is not so complicated thanks to new offers in the construction market. First, the locks have become more compact, secondly, manual frezer I simplified the insert.

With this tool, you can perform the necessary holes for installing the lock or loops in a couple of minutes. At the same time, the edges of the holes are perfectly smooth, without small jar.

On the this moment Installation of loops with full immersion technology into a box or without immersion is allowed. To facilitate the inserting technology, special card loops are developed and coming on sale, which allow you to spend the process very quickly without extra effort. The novelty of their design lies in the fact that they are superimposed on top of another, tightly adjacent and without forming the slightest gnesks.

It is not necessary to make samples to install such loops, and the canvas at the same time hangs very softly and conveniently.

Special attachment sets

Under certain new installation technologies for interior doors, whole fasteners are being developed that allow you to facilitate the process and make it easily fulfilled even for those who are not a professional.

These include patented SMS installation technologies, which was developed in Samara. She took into account all the complexity of the installation process and offered a whole list of principal innovations.

The technique is based on the use of a special attachment set, step by step guide To which it allows you to easily and high quality installation even to those who do it for the first time, not to mention specialists.

Each set consists of two half, one of which is attached to internal surface Box bar, and the second is on the go. When they are combined, you can affect the adjustment of the box even with the door inserted. Adjustment is carried out manually or using standard electrical instruments.

SMS kits have a submersible mount, but the box will not be drilled through that it saves decorative layer intact. In addition, in such a set there is all the elements without exception, so nothing needs to purchase anything else to install doors.

Another advantage is that it is possible to use such technology in the openings from different materials: from wood, concrete, brick, drywall, foam concrete, etc.

Thanks to the emergence of new technologies in the construction, allowing the perfectly installed doors, not only the convenience, but also the life of the product has improved. Therefore, it is still less likely when installing with old methods, but prefer new, which make it possible to make the process less time consuming and rapid.

Final stage of any overhaul In the apartment - replacement of interroom doors. Interior doors are usually an order of magnitude cheaper input, but to update the interior or a complete design change without their replacement can not do. Change them most often comprehensively, even if we are talking about a small one-two-bedroom apartment.

Technology installation of interroom doors. Video

Depending on what material do the doors and what kind of design they have, the installation technology will depend. Since the question arose about replacing interroom doors, the choice between the types of structures will be inevitable. The correct interroom door can save space in the apartment, if you give preference not by simple single-holder swing doors, and sliding, you can also consider the option to install the harmonica door.

SAMI simple design Without glasses for interior doors, it is performed from a set of canvas. Most often, the canvas are made from coniferous rocks Tree and almost all the doors of the economy class are lined with a felt plate. Fiberboard can be both profiled and simple, depending on the price category. The cheapest doors have a textured surface under painting, and models are more expensive.

Depending on the price category, it can be equipped with a door frame, loops and fittings. But most often, even in standard apartments panel housesIt accounts for a long time to customize the door under the box, because the nominal dimensions are not always followed, which is why before starting the installation of the door, you need to prepare the opening.

Preparation of facilities for installation

In the room there must be a floor, and the walls are prepared under finish finishThey must be plastered or past. Door box should be installed after all wet finishing workOtherwise, it can be a story, turn, especially at the bottom, which can deliver extra problems.

The door frame can be sold along with the door cloth, and maybe separately. In the case when the box is bought separately, it is very important to pay attention to the thickness of the door leaf and the status of the racks from which the box will be collected. The curvature and cracks are not allowed, it is also undesirable for bitch on the door frame elements.

Good loops and necessary tools

It is impossible to bypass the loop. Despite the fact that the loops on interior doors do not carry a special load, it is better to choose the models detachable and more expensive. Savings on the loops will further add trouble, and if the door is relatively heavy, it is better to install not two, but three loops. As a rule, those self-tapping screws that are sold complete with hinges are not suitable anywhere. They are disposable and made of low-quality steel. It is better to immediately replace them with proven good screws of a suitable configuration.

To install interroom doors with their own hands, the minimum set of tools will be required:

• construction level;
• drill or screwdriver;
• roulette, ruler, square, marker;
• assembly construction foam;
• set of chisels or electric toolreplacing them;
• fantasy saw or stubble with a hand saw on a tree;
• planer or mill.

The installation of the door block begins with the markup of the racks of the box. Internal size Boxes under the door should be 3-4 mm more sizes The door itself, and the distance from the lower edge of the door to the floor should be at least 10 mm. The rack is placed, after which they scream at an angle of 45 degrees fantorial saw and manual knife on wood. The assembly scheme is shown in the figure - the assembly uses self-tapping screws or wooden pins. Upper Planck The door frame is also cut down on the same principle - from the side of the castle and from the side of the loops of the gaps should be 4-5 mm.

It is more convenient to cut the loops and the castle when the box and the door are still in hand, so first you need to measure 20 cm on top and 21 from the bottom of the door and along the inside of the rack on which the loops will be mounted. The loop is attached to two self-pressing temporarily on the door frame, after which the contour of the pencil is burned. The loop can be removed and with the help of the chisel, perform a recess in the rack. The depth should be such that the loop is completely hiding in thickness.

It remains only to collect the door frame and consolidate it in the doorway. As a rule, interior doors are strengthened with mounting foam, but it is desirable to fix the box with large self-drawing or anchors to the wall. The box is set strictly by level and is recorded temporarily with a piece of drywall, foam plaster, boards, after which the free space is filled with foam.

The screws for fixing the box to the wall is best located on the hinge sites and on the pad to fix the lock. So the screws will not be visible, and three points are enough for durable attachment. You can hang the door and gate the space between the box and the wall. After checking the performance of the design, the box is closed by platbands that can be mounted on glue or thin nails.

The design is installed, it remains only to lubricate the loop and solve which lock will be necessary for the door. Successful to all repairs!

The interior door serves to separate space indoors, and also provides sound insulation in a private house or apartment. Besides, door leaf is an an important detail interior, therefore, it must correspond to the design style. As mounting work It is quite expensive, the question arises, how to correct the installation of interroom doors with your own hands. The answer is in the detailed step by step instructions outlined on this page.

Dimensions and equipment

According to the door opening method, there are folding, sliding and swinging. The latter are most popular because it is constructively the simplest and easy easy-to-install. They are represented by B. large quantities modifications. According to the opening method, the following distinguishes:

• double and single beds;
• levo and right-sided.

Step 3: Installation of the box and mounted canvas

The box must be installed in a pre-prepared opening. Rack with hinges must be aligned primarily using a plumb or level. It is necessary to check it from all sides. Then upper crossbar And the rack must be launched with wedges. The rack will be displayed only when it takes a vertical position.
Next fold the second rack. Be sure to check the horizontal part of the box.

Old fashion - Side racks must be drilled. To do this, in the wall initially make holes for the dowels. The box must be attached to the wall with self-draws with a length of at least 150 mm.

In order to fix the box in the opening hidden way, Metal plates can be used that are commonly used for installation. plasterboard structures. Most often, such plates are used with anchors. It is worth choosing the number of fasteners according to the expected load.

The use of such plates is non-standard way and perhaps only in absence finishing. It is recommended to stamp the wall of the wall so that fasteners are fastened.

It remains to hang the door on the frame. After that, you need to conduct final adjustment of the box. Then the rack for the lock should be fitted under the door so that it does not make it over the wall. It is worth remembering that to maintain the integrity of the box and the canvas, you must first drill several holes for screws.

Step 4: Switching

After fixing the web you need to simmer the gap between the box and the edge edges. The foam should be appropriately, along the layers, while the feed is produced from above so that it does not appear. Then the door will have to close and a certain time It is not touched to it so that the foam dried. Approximate drying time - 1 day.

If the composition accidentally hit the cloth - immediately remove it with a clean dry cloth, dried fragments are cleaned with the help of effective.

Step 5: Installation of the lock and handles in the door leaf

The most popular today are handles with a built-in lock. The order of work is as follows:

1. Make a mark on the meter from the floor. The mechanism of the handle must be applied so that in the opening from above the mark is visible.
2. Drill holes in a canvas from the end. The edges of the holes after that it is worth cutting off the chisel to align the hole.
3. Insert the mechanism into the hole. At the same time, the lock must be aligned, and after fixed using self-samples. The plank on the lock should be burned with a pencil for a break of a veneer, then the mechanism is to remove. According to the outlined circuit, you need to choose a pad to determine the thickness of the locking plate. This is done when using the chisel.
4. Drill holes for latch and handles. Need to attach a lock to the canvas with of different side, Align it and post it. The holes must be made on both sides and at the same time they should not be through.
5. Remove the resulting chips and set the handles.

Step 6: Installing Dobly Plans

Dobor is called a straight line about 2 meters, width - 250 mm, thick - no more than 3 cm. The bar should be applied during the installation of interroom doors, if the wall is thicker than the door frame.

The bar for the box is manufactured in standard width - Approximately 70 mm. It can be expanded according to the thickness of the discharge of good. This will allow you to more clearly combine the box and walls. The bar has a groove for the plank. Previously, it is necessary to measure the distance to the edge of the wall, ranging from the depth of the groove.

Dobor can be installed in different ways:

• in the groove existing in the box;
• with the cutting groove in the absence of finished;
• attaching a problem with the inside of a bar in the absence of a groove, the box is installed with the goodness;
• fastening of the goodness in the form "P";
• if the good is not too wide and there is no groove in the box, the bar is to drill and fasten to the box.

The bar is poured into several pieces of circular to get several kind of necessary dimensions. You need to cook one short bar and two vertical. Examine our simple step-by-step instructions by .

Step 7: Fasteners

During the installation of platbands, the box must be located at the level with the opening on the front side. To connect platbands, you must first apply the vertical bar to the box and put the mark above 0.5 cm, retreating from the crossbar of the box. This mark will act as the edge for the cut. In the same way, it is necessary to place a cut on the other side.