How to make a bench: original ideas (drawings, photo reports). Bench with your own hands. (100 step by step photos) A simple bench with a back

In order for the garden plot to be comfortable enough, it should be properly equipped. An important component are garden benches. You can make them yourself different ways and from various materials.

Bench made of concrete slabs and boards with a back

Looking at the drawings of the bench, you can find out the features of its device. You can make such a design with your own hands relatively easily, quickly and without high financial costs.

Making a bench with a backrest with your own hands step by step instructions described in great detail.

Assembly: the initial stage

After the preparatory work, the time for wood processing is coming. In order for a do-it-yourself bench with a back to serve for a long time and decorate the site, it is necessary to pre-process the materials.

wood cover antiseptic formulations and let dry. After that, you can start collecting backs.

On one of the two-meter boards, fifty centimeters are measured from the edges. At this level, the edges of the white will be located.tons of slabs. From this mark another fifteen centimeters are measured to the center of the board. Here the first boards will be attached. From the resulting marks we measure seventeen and a half centimeters - the gap between the boards of the back. Next, we measure fifteen centimeters for two more boards. Between them there should be a gap of five centimeters. All this can be seen in the drawing.

Wood glue is applied to sections of fifteen centimeters. Boards are applied to them, the length of which is sixty-five centimeters. Additionally, they are fixed with self-tapping screws.

From above, between the boards of the back, pieces of seventeen and a half centimeters are glued. In order for the parts to stick together well, they are clamped and held until the glue sets. After gluing is completed, the back is covered with an antiseptic.

Everything wooden details can be covered varnish. This will give them additional stability and attractiveness.

Assembly of the main part

It is better to collect the main part of the bench from two sides. Placed between the boards concrete plates, and threaded rods M16 fifty-five centimeters long are inserted into the drilled holes. They will need four pieces.

The rods are fastened with nuts and washers M16. Spin them at the same time different sides to make the bench level.

A simple bench with your own hands

You can make benches for giving with your own hands quickly enough if you follow the instructions. Consider four options for such garden structures.

On the drawings benches detail all its features. Making such a bench with your own hands is quite simple. The only difficult element is the concave seat.

The number of parts and their dimensions are indicated in the table.

The manufacture of benches with their own hands from wood begins with blanks the necessary details. Boards and timber are sawn into pieces of the desired length.

The manufacture of seat supports will be somewhat more difficult. You will need to markup on the blanks. Two points are marked along the edges at a distance of seven and a half centimeters from the bottom side, and in the center a point at a distance of four and a half centimeters. They are connected using a flexible plastic ruler and cut out jigsaw. Sections are treated with sandpaper.

Seat supports are attached to the two upper tsargs. One on each end and one in the middle. Next, the supports are screwed, spaced from the extreme ones by the width of the legs. All connections are made with self-tapping screws.

Boards are attached to the resulting base seats. It is desirable to deepen the hats of self-tapping screws.

Then attach legs. They are attached to the seat supports. The lower tsargs help to fix the legs.

The finished product is covered antiseptic and varnish.

Simple bench #2

To make such a garden bench with your own hands, you will need concrete flower girls and boards. Flower girls are required to create the base of the bench. Use two with rectangular base and two cubes.

In order for the base to be stable, the flower girls must be glued or connected from the inside with staples fixed with self-tapping screws. A layer of drainage and soil is poured into the tank. This increases their stability.

The seat for the bench is made of boards. To do this, they are cut into segments of the desired length. These blanks are laid so that they have a distance of half a centimeter. Then they are connected using cross bars. Planks are placed in three places: along the edges and in the middle. Corners are attached to the planks. With their help, the seat will be fixed on the flower girls.

Do-it-yourself bench with a back

Prepare the details of the bench shown in the figure. They are processed antiseptics before connection.

Then the supports are assembled from the parts. Pre-round the corners and chamfer. First, parts A and B are connected with a bolt, and then B, C and D are also connected using a bolt.

The inclination of the back is determined by part D, after which it is connected to part A. Similarly, but in a mirror image, another support is made.

After that, the back and seat are assembled. To do this, the supports are placed so that there is a distance of twenty centimeters between them. First, the front and rear bars are screwed to the supports, then all the others, and finally the stops are screwed.

At the last stage, the back of this bench is screwed.

Bench #4Another option for a simple do-it-yourself bench. Its length is one hundred and twenty centimeters. The height from the ground to the seat is fifty centimeters, the height of the back is also fifty centimeters.

The base is made from boards, whose thickness is five centimeters, and the width is from ten to twelve. One of the legs continues and is the backrest support. The supports are connected according to the “half-tree” method and fastened with bolts.

The basis for the seat is a bar fixed on self-tapping screws. The short legs on the back of the bench are colleted together to increase stability. The seat and back are sheathed with boards with a smaller thickness. The surface is painted or varnished.

A simple bench with a back for a summer cottage

The dimensions of the structure and wooden parts can be seen on drawings benches. If we consider how to make a bench with our own hands, then this option will be the most optimal in terms of the simplicity of the process and the result obtained.

Materials are best purchased already cut to size. If there is no such option, then you need to cut them yourself.

The resulting blanks polished. The ends of the boards are treated with an electric planer.

The rear legs of this simple do-it-yourself bench are also a support for the back. To create the desired level of inclination, the blanks are marked.

At a height of forty centimeters mark the place of attachment seats. Above the board is cut at an angle of twenty degrees. The cuts on the two blanks should be the same.

Gather first legs benches: the front ones are connected to the back ones with a beam. It is better to do this from above and below.

When the side parts are assembled, they can be connected to each other with seat boards. Screw the boards with self-tapping screws, leaving distances of one or two centimeters.

To strengthen the structure and increase its stability, make the lower strapping bar on the legs. Two boards are attached to the back.

Finish the work with a finish coated which will protect the product from moisture and adverse conditions.

Do-it-yourself pallet bench

Make a bench with your own hands pallets It's easy if you use your imagination. To do this, you need three or four of these wooden structures. Some will need to be cut to get additional details. The simplest do-it-yourself pallet bench design is when two pallets are attached perpendicular to each other, creating a back and seat.

So that the design does not turn out to be too cumbersome, it is better to cut the pallets to the desired dimensions. Fasten the elements with self-tapping screws. Add side details that enhance strength and make legs. All this can be seen in the photo.

Since the material of the pallets is raw, rough, it will need to be preliminarily grind. This will allow you to do without splinters.

The manufacture of benches with their own hands from pallets is being completed with varnish or paint.

Bench puzzle

You can make such a bench with your own hands, if available wide board and shovels for shovels. Figured seats are cut out of the board in the form of puzzle pieces. Legs from cuttings for shovels are attached to them. Separate stools are obtained, which are quickly assembled into one long bench. All stages of production are discussed in detail on step by step photos.

Benches from unnecessary chairs: two do-it-yourself options

First option

To create such a bench for a summer house with your own hands, you will need four old chair.

From the first two chairs filmed parts on the front of the seat.

The rest sawed off the front legs are slightly lower than the seat structure.

From the resulting details you need take off old varnish or paint. To do this, the parts are applied special agent, dissolving paint coatings. Then the softened layer can be removed with a spatula.

The racks should drill dowel holes. Holes are required on the front and end sides.

The dowels are smeared with glue and inserted into the drilled holes.

When the dowels are glued, you can collect base benches. To make the design durable, the parts are fastened with self-tapping screws. Construction surface sanded.

For seats benches choose a board that is suitable in size, saw off the excess.

If more than one is used narrow boards, then they are glued together with wood glue. For a tight connection, they are clamped with clamps and waiting for the glue to dry.

The finished seat is also glued to the base with wood glue. Heavy objects are placed on the board and clamped together with the base with clamps.

When the glue dries, cover the seat with masking tape and stain other structural elements with wood paint.

The adhesive tape is removed and the seat is processed wood stain. In conclusion, the entire bench is varnished.

Second option

To make a second garden bench with your own hands from old furniture you will need two chairs. It is better if the back and hind legs are not separated.

Two identical chairs clean up all parts of the structure except for the rear legs with a back.

take bars 5 cm wide and 3 cm thick. Two pieces are cut off, equal in length to the width of the chairs, and two pieces of the same length as the finished bench will be. From these four parts, a rectangle is assembled. It is fixed to the backs of the chairs with self-tapping screws.

Another frame is assembled in the same way. Several cross bars are attached to it. This design is attached under the seat, makes the bench more reliable and plays the role of a shelf.

If the chairs are old coating then remove it with sandpaper. After that, the surface is puttied with a special compound or coated with a primer. When the layer dries, it must be sanded with fine-grained sandpaper. At the end, the structure is covered with paint.

Do-it-yourself seat for a garden bench is made from Chipboard or plywood. A rectangle is cut out of the selected material, which is larger than the base by half a centimeter on each side. Then cut out a piece foam rubber with the same dimensions. From upholstery fabric cut out a rectangle. It should be larger than the seat by five centimeters on each side.

Foam rubber is laid on a sheet of plywood, it is covered with a cloth on top. The fabric is fastened from the inside with furniture stapler.

The seat is attached to the base with a piano loop.

Bench-swing

To make such a bench for giving with your own hands, you should prepare the necessary materials. Start manufacturing by creating basics designs. The seat bars are attached to the back bars at a selected angle.

Along the seat install additional ribs providing rigidity.

Attached to the seat planks, drilling holes in the base bars for fastening. The same goes for the back.

Armrests are installed on both sides of the seat. They can be bolted on.

The resulting bench cover wood preservatives and varnishes. It is very important to paint over everything as carefully as possible.

The bottom of the bench is reinforced with metal profile. Chains are attached to the profile, on which the swing bench will be suspended. Be sure to check the reliability of the beams on which the bench will be suspended.

log bench

To make such a bench with your own hands from wood, you will need chainsaw. A thick log one meter long is taken as the main material.

Log mark out, to get two slightly unequal parts. The back will be made from the smaller one, and the seat from the larger one.

Chainsaw log sawed along the mark. The resulting irregularities are immediately cut off with the same saw.

The cut triangular piece is cut into pieces and inserted into the holes in the seat. The back is fixed on top. The bench is almost ready. It remains only to give it a more decorative look.

Can the seat be placed on legs. To do this, recesses are made in the lower part for installing a pair of logs as legs.

Bench-transformer

Design features of the transformer can be seen in the drawings of the bench. A do-it-yourself transformer bench is made from planed boards, which is cut to the named sizes.

In sliced lumber details holes for fasteners are drilled.

At the tabletop, boards located on the edge can be made wavy.

In material intended for countertops, drill holes with a diameter of twenty-two millimeters and a depth of three centimeters. Cuttings of the same diameter will be inserted into them.

The edges of parts and edges are processed and rounded.

The assembly of all elements is carried out with screws and screws. Screws are needed with dimensions 6x70 and 6x90, screws - 8x80.

Wooden parts stain stain.

The structural parts that will move are connected by hinges.

Between the boards of the tabletop place parts of a round cutting.

Set the stop for backs.

A do-it-yourself transformer bench is covered varnish.

rocking bench

Making an original bench with a backrest with your own hands is not difficult if you have the tools and materials. First you need to consider the drawings of the bench, which contain a small amount of detail.

The side parts according to the pattern are transferred to euro plywood three centimeters thick. They are cut with a jigsaw and the ends are processed with a grinder.

To fix the connecting strips, markings are made. Then holes are drilled. After assembling the frame, the rails are fixed with self-tapping screws. The attachment points are spatulated, and the product is completely varnished.

Bench around a tree

The simplest version of such a bench - hexagonal. The size depends on the size of the tree. Measurements are made at the height of the seat. To the result obtained, another margin of fifteen to twenty centimeters is added. If you divide the result by 1.75, you get the length inside.

For cutting boards ten centimeters wide are laid in four rows at intervals of one centimeter.

The cut point is marked immediately for all rows with an angle of thirty degrees. So cut out six sets of blanks.

Legs are used with a height of sixty to seventy centimeters. They are connected by crossbars by drilling holes and using bolts with nuts.

The seat is installed so that the joints are located in the center of the ribs of the legs. Screw the outer pieces first, then the inner ones. In this way, the entire hexagonal structure is assembled around the tree.

At the end, they make a back and mount an apron. The result is a circular bench with a do-it-yourself backrest.

The finished product is processed oil impregnation.

Bench made of curved branches

A bench made of curved branches will look original. For you will need branches for the front, two legs, a horizontal top and a pair of transverse branches.

Sawing branches so that they match each other as accurately as possible. Then they are connected with metal corners.

Similarly, the back is made and connected to the front.

The finished product is placed on a flat area and the seat is assembled.

Bench options

• log bench, which goes well with surrounding nature. It consists of half a log used for the seat, and two short round logs that are legs.
  
• Beautiful wooden bench with a back and armrests, reminiscent of a sofa. Curved and carved elements make it more attractive, while left knots and bumps give the design a natural look.
  
• Bench made of wood and metal. The base of the structure is metal. The wooden parts of the seat and back are fixed to it. Due to the small thickness of the metal parts, it looks light.
  
• A bench of a simple, classical form. It is made of wooden, rather wide boards. This width allows you to comfortably sit on the bench. Armrests make the design more complete.
  
• original bench made of wood with curly details. This option is well suited for a site with a natural rural design. Carved legs and armrests, figured back - all this gives the product originality.
  
• Bench with an interesting back. The curved parts gradually deviate back, creating a unique design. The seat is slightly curved but has a more traditional look.
  
• Wood complex- a table with two benches. The design looks traditional due to the material used. original solution is the fastening of all components into a single structure.
  
• The bench is made from solid wood. cut from it one piece combining the back and seat. The legs are attached to the bottom. The log is required quite large.
  
• Bench with storage box for toys. Outwardly, it looks like an ordinary wooden bench-sofa, but under the seat it has a box in which you can put various things.
  
• Comfortable wooden bench with a simple shape. The base is made in the form of a rectangular box. The back is also simple with a straight shape. The seat is padded with soft cushions for added comfort.
  
• A wooden bench placed around a tree. It is made as if it consists of four benches, each of which has one armrest. The composition looks attractive and comfortable.
  
• Bench of a simple form from wide boards. It looks solid, but its dimensions are somewhat hidden due to the gaps between the boards and the light blue color in which it is painted.
  

One of the attributes of a garden or recreation area on suburban area- a bench, sitting on which you can read a book alone or, conversely, spend a few fun hours with friends. How to make an ordinary bench comfortable and at the same time turned into an element of garden decor? The way out is simple - a do-it-yourself bench for a summer residence. Only your own exclusive creation will fully satisfy your personal aesthetic needs.

Before you start sketching or drawing a product, you need to consider the place of its installation. The material of manufacture also depends on this. For example, in an old garden with large branchy trees, a wooden bench in a wrought-iron frame looks good (as an option - a log product on a stone base), and in a young garden - a light, even openwork bench in a romantic style.

A small white bench stands out in contrast against a dark green hedge

If it is placed in a quiet secluded corner, near or surrounded by blooming flower beds, it will become a wonderful place of solitude and relaxation, where you can spend a few pleasant minutes alone with yourself after a labor “warm-up” in the beds.

old Brick wall, a bench made of grayed wood and flowers look mysterious and romantic

Often benches are an integral part of verandas, gazebos, summer picnic areas. In this case, there should be several products designed in the same style. One example is garden table with two benches on the sides, behind which on a summer evening you can have a family tea party or fight board games.

Deliberately rough and comfortable wooden structure - a table, two benches and an armchair

It is better to install the bench in such a way that it does not offer a view of the neighbor's fence or garage, but of a pond, flower garden or. The surrounding picture should be pleasing to the eye, and not remind you that you need to refuel the car or renew the paint on the gazebo. It is also appropriate to place benches on the playground, by the pool, near the main entrance to the house.

A bench by the pond surrounded by flowers and greenery is a great place to relax and think

One of the best places is in the garden, near the beds. It is better if the bench will stand in the shade, for example, under the spreading crown of a tree or under a canopy, as it is designed to rest from physical labor - digging, weeding, watering or harvesting.

Rest in the shade of a flowering bush is a real pleasure

Can think decorative frame: a do-it-yourself garden bench looks good surrounded by low flowering bushes, specially arranged flower beds, on a small hill or on a natural stone site or.

Preparatory work is half the battle

First you need to take a piece of paper and make a sketch or drawing of the proposed product. Even at this stage, questions may arise: what height will be optimal or how many legs should the bench have? There are general standards that should be followed when drawing up a diagram:

• 400 mm - 500 mm - seat height;
• 500 mm - 550 mm - seat width;
• 350 mm - 500 mm - back height.

If you plan to create a product with a back, you should determine for yourself how the back will be attached to the seat. Depending on whether the bench is portable or not, legs are planned: for a non-portable product, they are firmly fixed in the ground.

It is not difficult to fix the legs of the bench: you need to dig holes right size and fill them with cement mortar, lowering the wooden parts there

According to the drawing, you can estimate how much material is needed for work. Usually, a product of this kind takes a minimum of financial investment: in the country there are always a lot of wooden blanks left over from the construction of a house or a bath, fasteners (self-tapping screws, nails, bolts, staples), paints and varnishes for wood processing.

If you collect the remains of wooden products and blanks from all over the country, you can come up with an unusual model

There is a utility room and the necessary tools. If the main material for manufacturing is wood, you should prepare: a plane, a saw, a jigsaw, a hammer, sandpaper, tape measure and pencil.

Making benches: six simple projects

You will never go wrong by choosing wood for work - soft, malleable in processing and at the same time durable, capable of serving for decades. Elements can be created from wood various shapes and size, curly inserts, voluminous and miniature details.

Project No. 1 - a simple bench with a back

If there are difficulties with drawing up a sketch, you can use the finished drawing of a garden bench.

All parts are cut according to the dimensions on the drawing.

This bench is traditional for city parks, similar specimens can be found at river stations, near theaters or shopping centers- in those places where you have to spend some time waiting. The advantage of this option is the ease of preparation of parts and the speed of assembly. For work, you will need thick bars for support (3 large and 3 smaller), bars or boards for the seat and back.

The color of the parts can be changed using impregnation or varnish of a darker shade.

This model is portable - it can always be rearranged to another, more comfortable spot. In order for it to always stand level and not sway, when installing the supports, it is necessary to monitor the exact location of the parts - even a slight discrepancy will cause the product to skew.

At the end of the work - and this applies to any wood product located on the street - all wooden parts must be treated with a special impregnation against mold or varnished, which also contains protective components. Treated wood resists moisture, lasts longer and looks like new for a long time.

Project No. 2 - a bench in a classic style

This option is more solid than the previous one. A bench with a rectangular seat and the same back looks great against the backdrop of a house built from any material - wood, brick, stone.

Scheme of assembly of armrests and backs of a bench in a classic style

For a change, you can change the color, choose a shade that is closer to summer cottages. The back of such a bench is a real find for those who like to dream up and translate their ideas into wood. Straight vertical bars can be replaced with crosswise slats.

This bench can easily accommodate several people.

The upper horizontal bar would look good if it was covered with elegant carvings or colorful ornaments. Armrests and legs can also be curly - but it all depends on the desire and skill of the master. To make such a bench for a summer residence, it will take only a few evenings, and you can enjoy your vacation on it for more than one year.

Project number 3 - a table with benches

The garden set for relaxing with the whole family consists of a comfortable table and two fixed benches.

A convenient and practical table with a couple of benches is useful in any country house.

All large parts (table, benches) are assembled separately, and then assembled into a single whole with the help of 4 lower bars - 2 on each side.

Assembly diagram of the whole set

The table is a tabletop with legs set crosswise.

Table assembly scheme

The benches are assembled easily, from bars or boards of various lengths.

Shop assembly scheme

At the last stage, the benches are first fixed - to give the structure stability, then - the table, exactly in the middle.

Initial assembly - connecting benches

Simple in appearance, but comfortable table will become a gathering place for family and friends in the evenings - for communication, evening tea drinking, relaxation.

Such a table with benches can be placed directly on the lawn

You can download more detailed drawings and photos of this project.

Project No. 5 - video master class

Variety of material, shapes and styles

Wood is a traditional, “warm” material for making benches, which is why products made from it are so different. Instead of machined bars, you can take natural material natural forms - and before us is not just a bench, but a real masterpiece.

The original bench is made from large pieces of sawn and processed logs.

It turns out that stone benches also exist, but they are valued rather than for functionality, but for aesthetics. You want to sit on a stone product only in the warm season, but you can constantly admire it.

A small stone bench harmoniously fits into the flower landscape

They look elegant and elegant, but only a professional blacksmith can create a bench for a garden with his own hands from metal.

Wrought iron bench among the violent colors looks more than appropriate

Combined benches and benches look interesting, built of stone and wood or decorated with textile items - capes, pillows.

Small pillows in pink and white, neatly laid out on a bench, make the garden corner cozy and homely.

That's all for today. We hope you found something useful for yourself. If you have any questions or wishes - you are welcome in the comments.

Good afternoon, today we will make a variety of benches with our own hands. I collected in this article all the SIMPLE WAYS make yourself a comfortable and beautiful bench. I will give detailed explanations and demonstrative photos, and tell you as clearly as possible how to make a bench. wooden(beams and boards) and improvised materials(pallets, pallets, old chairs, boxes, etc.). I will also give drawings, assembly diagrams, and step-by-step master classes.

Everything assembled models country benches I will post them according to their complexity - that is, we will start with the simplest and most concise ways - and end with real professional products worthy of the hand of a master. After this article, you will feel that you have become the very master who knows a lot about his business and can easily make a bench from absolutely any material, even if there is not much of it. And the bench will stand firmly on its legs and serve your family for years. And who knows, maybe you can even sell your benches to neighbors - because they will also want to have such country benches in your area. And later you will start doing it, too, according to my articles-lessons.

In this article, as well as in the following articles in this series, we will look at ...

1. benches made from old chairs.
2. Bench chaise longue in French style
3. Beautiful benches made from bed headboards.
4. Master class of an elite bench from a chest of drawers.
5. Country benches with a back - from timber and foam blocks.
6. Benches for giving - panel with support on a solid sidewall.
7. simple drawing benches from edged board- in 15 minutes.
8. Country benches with a curved side.
9. Slatted benches for giving - with a curved shape of the seat.
10. Benches with backrest and armrests - 23 models.
11. benches under a canopy or classic pergola.

So, let's figure it out. And let's start with the SIMPLE WAYS to make a country bench with your own hands.

Model #1

Bench for giving

FROM OLD CHAIRS.

Here in the photo below we see an original and very simple bench - which is easy to make with your own hands from unnecessary chairs. Everyone in the country has old shabby chairs. Once upon a time you left one chair in the rain varnish coating puffed up on them soft upholstery has long since spread into shaggy holes. It’s a pity to throw it away, you put it against the wall of the garage or in a shed - and it continues to deteriorate. Then another comrade chair was added to it - but it is still nothing, and you keep it on summer veranda. And sometimes you see shabby chairs with a warped leg at the entrance (someone took it to the trash).

All these old robbers can be given a new valiant life. Color them in daring juicy color. And cover it with a wide board - screw it onto self-tapping screws (so that they hold on to the leaky bottom of the chair, it can be strengthened wooden lining). Or screw not to the bottom but to the frame of the chair.

By the way, if you don’t have old chairs, it’s NOT a problem. Go to any flea market site - they sell a lot of old chairs for mere pennies. They are happy that they sold it. You are lucky that you found it.

If wooden chairs will have different height seats - this is easily solved by filing the legs of high chairs (or stuffing additional thick boards onto the seat frame of a low chair to raise the seat to the desired height.)

Chairs can be connected not only in the seat area - but also along their backs. Here on a step-by-step master class for making such a bench (photo below), we see how it is done:

• The attachment points along the rear line of the seat are a long wooden plank.
• The attachment points along the front line of the seat are a screed with screws (or just a butt, which is held due to the fact that the back bar prevents the chairs from dispersing).

We attach the side rails of the bench. We cut out corner groove on the handrail so that it fits into the frame of the chair back.

We sand the varnish coating from the chairs (we prepare them for painting). We prime before painting - a special primer for wood. We impregnate with a moisture resistant coating.

And attention - we add elements of strength. Bottom and top between the backs of the chairs - we nail short wooden planks-holders. They will unite the backs of the chairs - into a single common back of the country bench.

Cut out the board for the seat. Please note that special square cuts are made in it (so that the high “humps” of the chair legs pass through them.

This is how we get an elegant garden bench. It can be placed on the lawn of the garden in a place with a table - under a canopy, in a recreation area, on a veranda or terrace. And for the winter and rainy season to bring into the house.

And here is the idea of ​​​​how you can arrange chairs DIFFERENTLY under our future bench in the country - WITH A ROUND.

And you can also make a round garden bench around your favorite tree or lilac bush in your country house - also from chairs set in a circle with their backs.

Even if you found only 2 chairs at a flea market, you can still make an original bench with them - which only you will have.

Moreover, one exclusive idea is still hiding here - just for TWO chairs.

Here in the photo below we see how exactly from two old chairs you can make an elegant one with your own hands french bench.

In the photo diagram below, we see a master class - where it is shown how two backs from chairs - become side elements of the garden bench frame.

• First we do quadrangular seat frame(light wood in the photo below) - even scientifically it is called TsARGI (frame elements under the chair seat, or under the table top). We nail this frame to the lower bars of the chair back.
• And then, so that our bench does not sway back and forth, we make an additional coupler frame already in the lower part of the legs of the future laochka-goat. Scientifically, such a screed frame at the bottom of the legs is called a PRONG FRAME.
• We paint the entire product white and get a solid French bench for a beautiful holiday in the country.

If desired, a backrest can be attached to such a garden goat bench. Just nail to the side surface of the board chair frame. How it is done in the photo below.

Model #2

Country benches

FROM AN OLD BED.

And here are ways to create a beautiful bench for giving using backrests from an old bed.

One back is sawn as is in half. The halves will be used as side elements of the country bench.

Even if the back of your bed is not made of a solid shield, but is decorated with carved balusters, you can still make a bench according to this scheme.

The seat can be covered with a solid wooden shield. Or upholstered with boards-rails as in the photo below.

The second headboard can be used under the FOOT of the bench- from the front edge. How it is done in the photo below. The bottom frame of the bench can simply be tiled with edged planed board and paint. Or you can cut out a solid shield and put it on top of the frame.

You can use only one back to create a bench.

You can make a FRESH FRAME from a cut board for a country bench.

Or the frame for the seat - the frame of the bench - can be taken from the same material as the frame frame of the bed. How it is done in the photo below.

And pay attention. Here, part of the bed frame is PUSHED ON THE TOP - to increase the level of the seat.

A beautiful country bench can be made even using modules from any other furniture. For example from an old buffet. Let's say you have a sideboard, part of which is not subject to restoration (drunk guests fell and broke through the line of drawers).

Then fate itself tells you to make an exclusive bench out of it. Unusual to beat the rest of the buffet. And create cozy corner for family retreat.

And you don't want to put this designer bench out in the rain. You will find her a place of honor in your country house. And sew for her blue pillows with embroidery of snow-white patterns.

Model #3

SHIELD garden benches

OWN HANDS.

To immediately explain the term "panel board" - I'll show you this simple design- a mini-shop from cutting rooms kitchen boards. This is the classic panel structure benches. That is, the product is ASSEMBLED FROM SOLID SHIELDS.

In the photo below, the shields are connected in a groove way. The board-seat rides into the grooves on the legs-racks.

Below, the bench is made EXACTLY THE SAME - using the shield method. Only the material of the shield is more coarse and unhewn. And here they added a back - it was also cut into the grooves cut in the support shields.

• The fastening of the shields to each other can be GROOVE (as in the photo above) - where in one shield grooves are cut, and other shields enter the bottom. Such fasteners are used only in panels made from a SINGLE PIECE of WOOD. Glued boards are not suitable for this - they can delaminate in the places of their gluing.
• Also, for fastening, ADDITIONAL FASTENING ELEMENTS are used - wooden(tsargi, corner braces, prolegs), metal(corners, staples and perforated plates).

Village shops are made using the shield method. 2 side shields (these are legs) - are interconnected by a long board (this is a proleg). The board can be located in the lower part of the midsole, or in the upper part of the midsole - immediately under the seat board. In the photo below we see both of these ways of arranging the proleg under the bench.

As you understand, the shields you work with are not required to have the correct shape. It may be fragments of an old gnawed board - in which you carved flat lines support for SEAT AND BACK REST.

In the photo below, a one-piece shield plays the role of a support for both the seat board and the back board.

Here is the same principle - a solid support for the seat and back of the country bench.

And this beautiful white bench for giving is made according to the same principle. Only already from exactly sawn shields and painted.

Below we see a panel model of a bench with a back, where already 2 shields play the role of a support for the seat and back.

And these supporting SIDE PANELS are made at a slight angle of inclination. And so the bench turned out to be a seat with an inclination inward and a slightly reclined back. It is very comfortable to sit in such a bench.

And agree to do it, it is very easy to cut out such a bench with your own hands. Here the drawing does not have to be exact. Just do it to your liking. Light sidewall angle choose by eye.

• Side lean back - in the form of a long triangle (choose the angle of inclination yourself).
• Foot support for the seat - in the form of an elongated trapezoid (can be with or without tilt).
• A piece of thick timber is smoothed under the foot supports - so that the bench has a height. But if you have a wide board, then the legs will turn out higher at the bench, then it is possible without beam supports

All parts can be planted on ordinary nails.

To keep the bench from being so low(if you wish) you can make the footboards higher - put together several pieces of timber at once - put them on top of each other with a turret and fix them on the inside with a board (to keep everything together) or without a board just on nails.

And also such a bench can be PUT ON LEGS - also in the form of elongated trapeziums. Nazhki are stuffed from the inside of the seat support.

Bench SHIELDING can be KNOWN (that is, not solid, but consist of their boards, closed with each other by a bar-bridge). A simple country bench with a photo below just demonstrates this method.

And this garden bench made of thick boards is also made according to the same principle.

Model No. 4

EDGE BOARD benches

Do it yourself with your own hands.

And here's another simple model country bench. Simplicity is not only in the design, but also in the material. From one long edged board, you can make just such a garden bench quickly and easily with your own hands.

It can be supplemented with armrests, covered with a noble dark stain, or bright rich color paint.

On the sides of a country bench of this type, you can make coasters for books, beer, those things with which you like to relax in the country.

Let's look at the drawing of this country bench. We see that all the corners of the board cuts have a slope of 30 or 60 degrees. The dimensions in the drawing are in inches. One inch equals 2.54 cm.

We see the drawing from the side. The length of the back and seat is up to you.

We cut the board into the segments we need. And we assemble the bench for bolts, screws or nails.

To such a bench in the country, you can make a table for provisions. Or an ordinary shield shop.

Model No. 5

Shield benches for summer cottages

WITH CURVED SIDE SHIELD.

The shields that you cut out for the SIDES of your bench in the country can have SMOOTH ROUND LINES. Then the bench can become a real work of art - your creative work.

The seat in such a bench rests on the PLANKS stuffed under it from the inside of the sidewalls.

The back rests at the bottom - on the same bar as the seat, and at the top on a bar stuffed vertically along the back part of the curved sides.

The boards from which you cut out the curly sidewall can be processed along the edge, giving it roundness and smoothness (left photo below).

And curly sidewalls can be cut not from an ordinary shield, and from joinery with relief - the front of the cabinet or the old paneled door. Even the door handle can not be removed - but left for beauty (on the right photo of the bench below).

Model No. 6

Slatted bench for giving

How to do it yourself.

And from the carved sidewalls you can make an interesting RAIL BENCH. They get a round seat with smooth outlines and a curved back line.

In the photo below we see just such a convenient bench for giving.

The curvature of the bench is obtained due to the fact that narrow slats are stuffed AROUND THE FLEXIBLE PERIMETER of the figured side parts.

In the photo below we see a master class for making such a bench for a summer residence. In order for the slats not to bend under the weight of a seated person - for such a bench they make another frame curly element - along the center. All three parts are connected together into one common frame - simply by PUTTING THEM ON THE SLOTS OF THE LOWER RAILS (as in the photo below).

And then on this frame along its upper perimeter - we fill the rails on the screws.

If you want such a bench to be longer, then you just need to make not three curly frame models - but four, or five, or six. And of course, the stuffed slats must also be long.

Model No. 7

Quick bench -

from foam blocks with a cavity.

Foam blocks (or gas silicate blocks) are sometimes made with through holes inside. This is done to save material and also to enhance the heat-shielding properties of such a building material.

And we can use this "leaky" feature of gas silicate blocks - for the good purposes of creating a bench in the country.

To do this, we install 2 two rows of foam blocks with holes DOWN, and put more foam blocks upstairs with holes on the side. And in these holes we insert a beam of a suitable section. To make it more comfortable for the pope to sit upstairs, you can put foam pillows. It is better to choose those that are lined with waterproof fabric. Or sew it yourself from oilcloth and thick foam rubber (sold in household stores and construction stores).

You can simply hammer it with a sheathing of boards into a solid one - so that a flat seat without holes turns out.

And it’s also good to cover the foam blocks with ordinary paint - to get a bright beautiful bench.

Here are some ideas for making country benches with your own hands. But this is not all the models of wooden benches that I would like to tell you about. Therefore, wait for the continuation - we will make interesting benches from wood (beams, boards and logs).

Your professional growth will not end there...

You will see how easy and quick it is to make a real building with your own hands - a large summerhouse. How to install pillars, how to make a roof yourself (without any building education), how to cover it with a roof (polycarbonate, slate, tiles). Stay with our "Family Bunch" - and we will give you "golden hands".

Good luck with your home building.

Olga Klishevskaya, specially for the site

If did you like this article
And you want to thank our free author for this painstaking work,
then you can send any amount convenient for you
on the his personal Poison wallet - 410012568032614

Items of garden furniture are needed to equip on suburban area resting place of your choice. Photos of benches in the garden look attractive. Any master can make such furniture himself.

First you need to decide on the choice of material for the future product and choose the right design solution.

Work materials

Garden bench can be made from various materials. Each of them has its own advantages.

Plastic bench

This piece of furniture has many advantages. Plastic products affordable, they do not require special care, they are easy to disassemble and assemble. Today, plastic is presented in rich colors.

However, there are also disadvantages. The plastic item looks cheaper than wooden product. Under the influence of direct sun rays it quickly burns out, and its surface can be deformed.

Wood for garden furniture

To make original benches for summer cottages, craftsmen often use wood. Wood is easy to process, the material looks noble, and installation does not take much time.

The main requirements are the absence of defects and good drying.

stone products

The naturalness of the material is its indisputable advantage, it attracts with its natural beauty. In finished products, it looks luxurious and stylish.

Natural stone items are easy to make with your own hands. However, the material has not only advantages, but also disadvantages:

• It is unhealthy to sit on a cold stone.
• The bench is installed exclusively permanently.

What about metal?

Metal benches are a great decoration for a recreation area. The cold forging method, like the hot forging method, allows you to create beautiful designs.

In addition, metal is perfectly combined with glass or wood.

What should be the ideal shop?

Among all the requirements, the main ones can be distinguished:

• Comfort. The bench needs to be ergonomic. A bench with a back is a good option.
• The product must be capable of withstanding heavy loads. The master needs to choose exclusively quality materials and accessories.

Bench design features

A summer resident who wants to ennoble the landscape around the house should know how to make a bench with his own hands. You must first determine the dimensions.

Dimensions - 1.5 mX0.4 m, height - 0.45 m (seat) and 900 m (back). The back is made at an angle of 18 or 20 degrees. It is important to correctly execute the drawings of the bench, then the work will not argue.

The master will need to prepare the following:

• Primer, varnish;
• Special sandpaper for wood;
• Screwdriver;
• Electroplaner;
• Electric jigsaw;
• Self-tapping screws 40X40;
• Blanks for front and rear legs, as well as for backrest holders;
• wooden boards with dimensions 1500X150 and thickness from 35 mm to 40 mm.

Making a wooden structure with your own hands

It's good when you can find boards with the right dimensions on the market.

When suitable option did not appear on the construction market, the master will have to arm himself with a jigsaw in order to cut the material himself. A miter saw will help speed up the process.

Note!

Finished blanks must be processed. The surface of the boards for the backrest with the seat needs to be sanded. The ends are processed using an electric planer, best option- make them with a rounded shape.

The next step is to give the required angle of inclination, in this case we are talking about the rear legs of the bench. These elements serve as a framework. Marking is applied to the prepared parts.

We measure the height - 0.4 m. It is necessary to make a cut equal to 20 degrees to form the angle of inclination. Between the legs of the bench in front and behind the distance should be 0.28 m. A beam with a size of 0.5 m connects the legs. It is better when the strapping is performed not only from above, but also from below.

The sidewalls are connected as soon as the assembly of the main parts is completed. The boards are fastened with self-tapping screws to the strapping bars that are on top. Between the blanks leave gaps to remove moisture.

When mounting the backrest, the board that comes first is attached at a distance of 0.2 m from the seat, and the second - 0.38 m.

Note!

You can proceed to the final coating of the product. For this, impregnation with varnish for outdoor use is used. Such funds will help ensure reliable protection from any harmful actions from the outside.

How to create a metal structure?

A master can create a comfortable place for a recreation area using the cold forging technique. It is better to start with models that have angular shapes, they are easier to make.

Detailed instruction

We determine the dimensions (length - 1.5 m, height - 0.8 or 0.9 m, width - 0.4 or 0.5 m).

We make blanks for the frame from a cut pipe. It will be necessary to prepare 2 segments with dimensions of 0.4 m and 2 more fragments of 1.5 m each. We connect these parts into a rectangle and weld them. To make the structure more durable, we weld 2 stiffeners.

To make blanks for the legs, we cut the metal pipe into 4 parts, the length of each should be 0.4 m. The blanks are attached to the corners of the bench. To reinforce the legs, stiffening ribs are additionally installed.

Note!

For the manufacture of the back you will need 2 blanks. The length of one should be 1.5 m, and the other 0.44 mm. We weld the blanks for the back together and weld to the seat. We must not forget about the angle of inclination. For the rest to be comfortable, it must be at least 15 or 20 degrees.

The backrest can also be reinforced with stiffeners.

At the last stage, the seams are cleaned. The surface of the frame is coated with a primer.

If you plan to make a product with figured elements, then the implementation of such a task will require more time.

DIY shop photo

A garden bench is not just ordinary furniture designed for relaxation. With this furniture you can decorate household plot, to create whole compositions that will fit perfectly into the surrounding space of the garden or yard. It is not difficult to make a garden bench with your own hands, the main thing is to choose the design of the furniture, its location and the material from which it will be made.

Garden bench materials

Plastic

Lightweight plastic furniture has a lot of advantages: it is easy to move from place to place, it is easy to take care of it, it has an affordable price category. You can choose any color option that fits perfectly into the landscape design. Cons of plastic furniture: quickly covered with scratches, fades in the sun, looks cheap.

Tree

This material is ideal for creating furniture: it absorbs heat, looks noble, and is easy to process. For the manufacture of benches, any type of wood is suitable, the main thing is that the material is sufficiently well dried and does not have external defects.

A rock

This natural and beautiful material fits perfectly into any stylistic direction. landscape design. Stone compositions look solid, noble and unusual. But, despite many advantages, natural stone has several disadvantages. Sitting on a stone bench is not very comfortable, and it is not safe for health either. Therefore, together with the bench, it is imperative to make warm covers or pads. Stone compositions are installed permanently, they cannot be moved from place to place.

Metal

Garden benches, made by hot or cold forging, are a real decoration of a garden or a place to relax. The designs look beautiful, stylish, especially if additional decorative elements. Metal is most often combined with wood, glass or other material.

Requirements that a garden bench must meet

Convenience

First of all, you need to think about the ergonomic design of furniture for relaxation. It should be comfortable and comfortable. It is best to make furniture with a back on which you can lean back and relax.

Safety

The garden bench must be strong, carefully assembled and withstand heavy loads. For these purposes, it is best to use high-quality materials and accessories.

Resistant to changes in humidity and temperature

Since the furniture is made for the garden or courtyard, the material must withstand all climatic changes without defects and damage.

Prices for garden benches

garden benches

Bench design

The length of the seat and back will be 1500 mm. Three people can comfortably accommodate on this furniture. Seat height - 450 mm, back height - 900 mm. The back is preferably positioned at an angle of 18-20 degrees. The seat width is 400 mm.

Material and tools for making a wooden garden bench

1. Wooden boards 1500 by 150 mm, 35-40 mm thick. Three blanks for the seat and two for the back.
2. Blanks that act as legs and holders for the backrest - 900 by 150 mm, 35-40 mm thick.
3. Blanks for the front legs of the bench - 360 by 150 mm, 35-40 mm thick.
4. Beams 40 by 40 mm will be used to reinforce the design of the bench.
5. Self-tapping screws.
6. Electric jigsaw for cutting boards.
7. Electric planer for grinding the surface of boards and chamfering.
8. Screwdriver.
9. Sandpaper.
10. Lacquer and primer.

Making a wooden structure

Step 1. Boards for making benches can be purchased immediately in size, if there are none for sale, the wood will have to be cut into blanks using a jigsaw or a miter saw.

After the wood is cut into desired length, it needs to be handled carefully. The blanks for the back and seat need to be sanded. All ends of the boards also need to be processed with an electric planer, it is desirable to give them a rounded shape.

Step 2. The long rear legs of the bench, which are additionally a frame for the backrest, must be given correct angle tilt. To do this, you need to mark two wooden blanks with a length of 900 mm.

The first is the height of the bench - 400 mm. This section of the board does not need processing. Starting from the segment, you need to make a cut of 20 degrees along the rest of the board, which forms the angle of inclination of the back of the bench. The cuts on the two rear legs should be the same both in height and in the angle of inclination. Otherwise, the bench will be skewed.

Step 3 The legs are assembled first in the design of the bench. The distance between the front and rear legs is 280 mm. The legs are connected with a beam, which is cut to the entire width of the bench - by 500 mm. It is advisable to do double strapping - top and bottom.

Step 4 After the two sides of the bench are assembled, you can connect them together with boards designed for sitting. Boards are screwed with self-tapping screws to upper beams strapping. It is desirable that gaps of equal size remain between the wooden blanks - 1-2 cm. These gaps contribute to air circulation and moisture removal.

Step 5 Strengthening the structure of the bench. In order for garden furniture to be stable and durable, it is desirable to strengthen its design. For these purposes, you need to make the lower trim along the legs with the help of beams. Two blanks, having a length of 1500 mm, are screwed to the front and rear legs of the bench. If there is not enough lumber, you can use one cross-beam, which is attached to the bottom rails of the strapping.

Step 6 Bench back assembly. The bench is almost ready, left finishing touch- fastening of two boards that act as a backrest. The first board is recommended to be fixed at a distance of 200 mm from the seat. The second - at a distance of 380 mm from the seat.

Step 7 Finish coat garden furniture. To protect the wood from environmental influences, it is desirable to use varnish. Impregnation will protect the bench from moisture, mold, insect pests.

Lacquer will give the furniture a beautiful and elegant look. To give the wood a shine, you need to thoroughly polish the material, and varnish the blanks several times.

Video - Detailed instructions for making a garden bench

Video - Shop in 6 minutes

Find out a few interesting options how to do, from our new article.

DIY metal garden bench

Decorating your backyard is not only wooden furniture. Metal benches are another way to create a cozy and comfortable place to relax. To make a metal frame, it is not necessary to master the technique of hot forging.

You can apply the technology of cold forging, in which the frame of metal blanks is welded into a single structure. Can be refined during production various elements decor, unusual inserts and additions.

Tools and materials for the manufacture of a garden bench by cold forging

1. Angle grinder with discs for cutting and polishing metal.
2. with a set of electrodes.
3. Pipe bending device. This can be a mini-machine "Snail" or a bench vise with which you can bend metal according to a template. This device is necessary if a complex shape of the back with rounded edges is planned.
4. Square metal pipes (30 mm by 30 mm).
5. Decorative elements of hot forging to decorate the structure.
6. Seat and back material (wood, MDF, plywood).
7. Roulette.
8. Level.
9. Primer for metal.
10. Protective coating for wood.

Step-by-step instruction

It is quite difficult to make a complex and elaborate design of a bench without experience. But make it simple solid construction possible without difficulty.

Step 1. Develop the dimensions and dimensions of the bench. A standard-sized garden bench has a length of 1500 mm, a width of 400-500 mm, and a back height of 800-900 mm. Corner forms of furniture are the easiest to make, so for the first time it is better to try to make a model simpler with your own hands.

Step 2 Making a frame for a seat. The metal pipe needs to be cut into 4 fragments: 2 by 1500 mm and 2 by 400 mm. All details in a rectangle. To make the seat more durable, you can weld 2 additional stiffeners into the rectangular frame.

Step 3 Leg manufacturing. The metal pipe needs to be cut into 4 identical pieces of 460 mm each. These blanks need to be welded to the corners of the bench. It is recommended to weld additional stiffeners between the front and rear legs.

Step 4 Back making. Two workpieces with a length of 440 mm and one workpiece with a length of 1500 mm must be welded together. Then this design is welded to the already finished part of the bench. The back should be attached at an angle of 15-20 degrees. In this case, sitting on the bench will be comfortable.

Step 5 To make the back of the bench stronger, you can additionally strengthen its frame with stiffeners, transverse or longitudinal.

Step 6 The metal frame of the garden bench is ready. The final work is the cleaning of all welding seams, polishing the metal and coating the frame with a primer.

Step 7 Wooden back and seat. Wooden boards or beams - the most suitable material for finishing a metal bench. The wood for the back and seat must be carefully planed and polished, the chamfers are processed. The tree needs to be cut into blanks that can be mounted both along and across the back and seat. It all depends on the length of the material.

Step 8 Using an electric drill, it is required to drill holes in the metal frame of the bench for mounting the wooden trim of the bench. To connect metal and wood, it is recommended to use bolts with rounded heads and nuts.

Step 9 After the backrest and seat are bolted to metal frame, the tree needs to be stained or varnished. This will protect the material from environmental influences.

The bench for the garden is ready. Due to the fact that the metal pipe is hollow inside, the furniture is not very heavy and can be moved from place to place. Well-crafted metal and wood are easy to bear high humidity and temperature fluctuations, thanks to which a hand-made bench will serve for many years.

Video - Making a garden bench from a metal corner